rozdzielnice dwujęzyczne
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Konserwacja i czci zamienne
Maintenance
5
and Spare Parts
5.16.2 Jakie s minimalne wartoci rezystancji izolacji? 5.16.2 Which minimum insulation resistance must be available?
W celu wyeliminowania wpływu pojemnoci reaktancji pomiary naley
dokonywa przy napiciu stałym.
Wartoci pomiarów napicia izolacji oraz minimalnej rezystancji
izolacji zamieszczone s w poniszej tabeli.
In order to exclude the influence of the capacitive reactance, the
measurements must be performed with DC voltage.
For the values of the measuring voltage and the minimum insulation
resistance, please refer to the table below.
Pomiary ochronne i napicia znamionowe
Protective measure and rated voltage
Napicie bezpieczestwa, funkcjonalne /
niskie napicie z izolacj bezpieczestwa /
Safety extra-low voltage, functional extra-low
voltage with safe isolation
Separacja ochronna /
Protective separation
Napicie znamionowe ≤ 500 V, oraz napicie
ochronne bez izolacji bezpieczestwa /
Rated voltage ≤ 500 V, and functional extralow
voltage without safe isolation
Napicie znamionowe > 500 V, ≤ 1000 V /
Rated voltage > 500 V, ≤ 1000 V
Napicie obwodu pomiarowego
AC [V]
Measuring-circuit voltage AC [V]
250 ≥ 0,25
500 ≥ 1
500 ≥ 0,5
1000 ≥ 1
Minimalna warto rezystancji izolacji [MΩ]
Minimum insulation voltage value [MΩ]
5.16.3 Wymagana dokładno pomiarów. 5.16.3 Required measuring accuracy
Błd pomiarowy nie moe przekroczy ±30%. Warto ta zgodna z
norm DIN VDE 0413 cz 1 wydaje si za dua. Z rysunku powyszego
wynika, e rezystancja izolacji składa si z wielu czynników
składowych, które z kolei zale od innych. Powoduje to du zmienno
wartoci tej rezystancji.
The operating error within the marked measuring range must not
exceed ± 30 % with respect to the value reading. This error range
permitted by DIN VDE 0413 part 1 initially seems to be very high.
From the equivalent circuit diagram above, however, it becomes
obvious that the insulation resistance is composed of a fixed
component and four other components which may vary according
to different parameters. This results in the large variation range.
5.16.4 Pomiary minimalne (przy dokładnoci ±30%!) 5.16.4 Minimum readings (Note recommended operating
error of - 30 %!)
Pomiary ochronne lub napicie znamionowe
Najnisze napicie 0,36
Napicie znamionowe ≤ 500 V 0,7
Napicie znamionowe ≥ 500V, ≤ 1000V 1,4
Uwaga:
Rezystancja [MΩ]
Ocena wyników pomiarów powinna take uwzgldnia cało-
ciowy stan systemu!
Protective measure or rated voltage
Extra-low voltage 0.36
Rated voltage ≤ 500 V 0.7
Rated voltage ≥ 500V, ≤ 1000V 1.4
Remark:
Reading [MΩ]
The assessment of the measured values has to take into account
the overall condition of the system!
5.16.5 Pojemnoci obwodów 5.16.5 Capacitive charges
Dla dłuszych linii kablowych naley odczeka, a kabel osignie
swoj pojemno, a wskanik urzdzenia pomiarowego ustali si.
Naładowany odwód, po pomiarach powinien by
rozłczony w celu ochrony przed poraeniem.
For longer leads and cables, first allow the capacitive charging
process to be completed and the indicator of the measuring device
to come to a standstill before performing the reading.
If a capacitive charging process was observed,
the leads must be discharged after measurement
in order to prevent electric shock.
96
MNS DTR / MNS Service