Mobil luftkonditionering Mobile Air Conditioner Liikuteltava ...

More documents

Recommendations

Info

34 Foam seal Foam seal A (adhesive type) Fig. 14 Fig. 15 Fig. 16 Fig. 17 26.5"- 48" INSTALLATION IN A SLIDING SASH WINDOW 1. Cut the foam seal (adhesive type) to the proper length and attach it to the window frame. Fig. 14. 2. Attach the window slider kit to the window stool. Adjust the length of the window slider kit according to the width of window, short the adjustable window kit if the width of window is less than 27 inches. Open the window sash and place the window slider kit on the window stool. Fig. 15. 3. Cut the foam seal (adhesive type) to the proper length and attach it on the top of the window. Fig. 16. 4. Close the sliding sash securely against the window. 5. Cut the foam seal to an appropriate length and seal the open gap between the top window sash and outer window sash. Fig. 17.
Adaptor cap Fig. 18a Fig. 18b Push in Expansion plug position Hook Adaptor A Fig. 19 Fig. 20 max 120 cm min 30 cm Fig. 21 Fig. 22 EXHAUST HOSE INSTALLATION The exhaust hose and adaptor must be installed or removed in accordance with the usage mode. COOL mode Install FAN mode Remove DEHUMIDIFY mode Remove 1. Install the window Exhaust adaptor B onto the exhaust hose as shown in Fig. 18a. or Fig. 18b. Refer to the previous pages for window kit installation. 2. Place the exhaust hose against the air outlet opening hook (See Fig. 19). When installing the exhaust hose, in order to install easily, the exhaust hose should be kept straight. Do not bend the hose (See Fig. 20). The exhaust hose can be installed into the wall 1. Prepare a hole in the wall. Install the wall Exhaust adaptor A onto the wall (outside) by using 4 expansion plugs and wooden screws, be sure to fix thoroughly (See Fig. 21). 2. Attach the Exhaust hose to the Wall exhaust adaptor A. Note: Cover the hole using the adaptor cap when not in use. The duct can be compressed or extended moderately according to the installation requirement, but it is desirable to keep the duct length to a minimum. IMPORTANT: Do not over bend the duct (See Fig. 22). 35
Page 1 and 2: Modell / Malli / Model: M09CR 94 41
Page 3 and 4: SE I den här manualen finner du m
Page 5 and 6: NAMN PÅ DELAR Framsida 1 2 3 Fig.
Page 7 and 8: ANVÄNDNING KYLLÄGE • Tryck på
Page 9 and 10: 67,3 cm - 122 cm (26,5" - 48") Damm
Page 11 and 12: Tryck in Fig. 18a Fig. 18b Krok Pos
Page 13 and 14: Ta bort skruven och ta bort gallret
Page 15 and 16: FI Tästä käyttöohjeesta löydä
Page 17 and 18: OSIEN NIMET Etupuoli 1 2 3 Kuva 2 T
Page 19 and 20: KÄYTTÖ JÄÄHDYTYSTILA • Paina
Page 21 and 22: 67,3 cm - 122 cm (26,5" - 48") Pöl
Page 23 and 24: Kuva 18a Kuva 18b Työnnä Koukku S
Page 25 and 26: Irrota ruuvit ja ritilä Irrota suo
Page 27 and 28: EN In this manual you will find man
Page 29 and 30: NAME OF PARTS Front 1 2 3 Fig. 2 Re
Page 31 and 32: OPERATING INSTRUCTIONS COOL OPERATI
Page 33: 67.3 cm - 122 cm (26.5" - 48") Foam
Page 37 and 38: Remove the screw and take the air i
Page 40: MP-JA-091229 Malmbergs Elektriska A

Mobil luftkonditionering Mobile Air Conditioner Liikuteltava ...

Create successful ePaper yourself

Delete template?

Save as template?