Manual utilizator Slope - GeoStru Software
Manual utilizator Slope - GeoStru Software Manual utilizator Slope - GeoStru Software
67 Slope Coeficientii de sigurantã minimi impusi de normativã se regãsesc în tabel: Modalitatea de cedare Cedare la întindere a barei de otel Coeficient de sigurantã minim (normativã) f max =0,5 fy Smulgere/pullout mortar barã 3 Cedare la forfecare a terenului adiacent 2 Rezistenta la întindere a barei de otel f y = 460 Mpa (tensione limitã de curgere otel); Φf y = 0,5 f y = 230 Mpa (efort maxim de întindere al otelului). Forta de întindere maximã a barei de otel T a = (Φ x f y ) x (d - 4) 2 × / 4 Tintuire/ Nailings Lungime barã (m) Diametr u barã (mm) Distanta orizontal ã între bare (m) Forta pe metru de lungime (KN) Forta cerutã (KN) Forta de tractiune maximã admisibil ã (KN) Check (Ta>Tr) E 8,0 25 2,0 8,0 16,0 79,66 ok D 8,0 25 2,0 15,0 30,0 79,66 ok C 8,0 25 2,0 20,0 40,0 79,66 ok B 12,0 32 2,0 50,0 100,0 141,62 ok A 12,0 32 2,0 55,0 110,0 141,62 ok T abe l de c alc ul a re zist e nt e i la înt inde re a bare i de ot e l Smulgere între bara de otel si mortar f c u =32Mpa, rezistenta cubicã a mortarului la 28 de zile =0.5 pentru bare de tip 2 (deformabile) SF= 3, coeficient de sigurantã Forta maximã admisibilã între mortar si bara de otel: [ β (f c u ) 1 /2 ] × × (d - 4) × Le / SF © GeoStru Software-Slope 8.0.1
SLOPE 68 Le= lungimea efectivã a barei (lungime mortar) Tintuir e/ Nailing s Lungi me barã (m) Diamet ru barã (mm) Distant a orizont alã între bare (m) Lungim e liberã La (m) Lungim e efectiv ã (m) Forta pe metru de lungim e (KN) Forta cerutã (KN) Forta de întinde re maxim ã admisi bilã (KN) Check (Tmax >Tr) E 8,0 25 2,0 4,70 3,30 8,0 16,0 205,26 ok D 8,0 25 2,0 4,20 3,80 15,0 30,0 236,36 ok C 8,0 25 2,0 3,70 4,30 20,0 40,0 267,46 ok B 12,0 32 2,0 3,80 8,20 50,0 100,0 680,06 ok A 12,0 32 2,0 2,30 9,70 55,0 110,0 804,46 ok V e rific are la sm ulge re înt re bara de ot e l si m ort ar Lipsa de aderentã între mortar si teren Tf= ( D c '+ 2 D K σ v ' tanφ) Le (Forta mobilizata intre mortar si teren) K = 1 - ( / 90) (1-K ο) = 1 - ( / 90) (sinφ), factor de inclinatie Granit complet descompus (CDG) cu K = 0.897 T f = ( D c '+ 2 DK σ v 'tanφ) Le = (1.571 + 0.14σ' v ) × Le= (1.571+ 0.140 σ' v ) Tintuiri/Nailings Zona rezistentã Adâncimea punctului mediu a lungimii Lungime efectivã strat CDG (m) efective Strat CDG Le CDG WATER E 3,30 3,40 0,00 D 3,80 5,30 0,00 C 4,30 7,20 0,00 B 8,20 9,70 1,40 A 9,70 9,40 3,00 Carac t e rist ic i ge om e t ric e ale bare lor de ot e l Tintuiri/ Tensiune Rezistenta Rezistenta Forta F.O.S. Check © GeoStru Software-Slope 8.0.1
- Page 19 and 20: UTILITY 16 Alt + S Alt + M Alt + C
- Page 21 and 22: NORMATIVE 18 different combinations
- Page 23 and 24: NORMATIVE 20 Structure Partial fact
- Page 25 and 26: NORMATIVE 22 strips and rafts. 2. S
- Page 27 and 28: NORMATIVE 24 state, a settlement ca
- Page 29 and 30: NORMATIVE 26 experience. 6.5.3 Slid
- Page 31 and 32: NORMATIVE 28 2.A presumed bearing p
- Page 33 and 34: NORMATIVE 30 distribution of loads
- Page 35 and 36: NORMATIVE 32 Ground type A B C D E
- Page 37 and 38: NORMATIVE 34 3. The reference peak
- Page 39 and 40: NORMATIVE 36 T B is the lower limit
- Page 41 and 42: NORMATIVE 38 Figure 3.2 - Re c om m
- Page 43 and 44: NORMATIVE 40 5. The elastic displac
- Page 45 and 46: NORMATIVE 42 4.For the horizontal c
- Page 47 and 48: NORMATIVE 44 than the value of a g
- Page 49 and 50: NORMATIVE 46 5.The design seismic i
- Page 51 and 52: SLOPE 48 sustinere din pãmânt arm
- Page 53 and 54: SLOPE 50 Exe m plu de fisie r ge ne
- Page 55 and 56: SLOPE 52 Adâncime BedRock: Adânci
- Page 57 and 58: SLOPE 54 numãrului de lovituri si
- Page 59 and 60: SLOPE 56 4.9 Caracteristici geotehn
- Page 61 and 62: SLOPE 58 Densitatea relativã: pent
- Page 63 and 64: SLOPE 60 3. Deplasati-vã cu mouse-
- Page 65 and 66: SLOPE 62 4.12.2 Siruri de piloti Se
- Page 67 and 68: SLOPE 64 Note despre lucrãri Pentr
- Page 69: SLOPE 66 medie a armãturii/ranfors
- Page 73 and 74: SLOPE 70 4.12.5 Pãmânt armat Se p
- Page 75 and 76: SLOPE 72 iesi din comandã apãsati
- Page 77 and 78: SLOPE 74 Pentru a calibra imaginea
- Page 79 and 80: SLOPE 76 valoare parametrului ales
- Page 81 and 82: SLOPE 78 forfecare ( ) si comparate
- Page 83 and 84: SLOPE 80 raportul de calcul. Slope
- Page 85 and 86: SLOPE 82 alegerea acestei comenzi d
- Page 87 and 88: SLOPE 84 în care tubul este imers
- Page 89 and 90: SLOPE 86 4.17 Suprapresiuni interst
- Page 91 and 92: SLOPE 88 obtinutã din încercãri
- Page 93 and 94: SLOPE 90 functie de indicele de pla
- Page 95 and 96: SLOPE 92 4.17.3 Calculul NL Calculu
- Page 97 and 98: SLOPE 94 - T M AX este întreaga du
- Page 99 and 100: SLOPE 96 criteriului de cedare Coul
- Page 101 and 102: SLOPE 98 normale totale sunt unifor
- Page 103 and 104: SLOPE 100 Ac t iuni pe fâsia i c o
- Page 105 and 106: SLOPE 102 Calc ulul fac t orului de
- Page 107 and 108: SLOPE 104 actioneazã pe suprafata
- Page 109 and 110: SLOPE 106 Se presupune cã în abse
- Page 111 and 112: SLOPE 108 Ac t iuni pe fâsia i c o
- Page 113 and 114: SLOPE 110 Ac t iuni pe fâsia i c o
- Page 115 and 116: SLOPE 112 - Ky sunt luate ca orizon
- Page 117 and 118: SLOPE 114 4.18.2.2 FEM Pentru bazel
- Page 119 and 120: SLOPE 116 118(12), 1889-1905 [26] C
SLOPE 68<br />
Le= lungimea efectivã a barei (lungime mortar)<br />
Tintuir<br />
e/<br />
Nailing<br />
s<br />
Lungi<br />
me<br />
barã<br />
(m)<br />
Diamet<br />
ru barã<br />
(mm)<br />
Distant<br />
a<br />
orizont<br />
alã<br />
între<br />
bare<br />
(m)<br />
Lungim<br />
e<br />
liberã<br />
La<br />
(m)<br />
Lungim<br />
e<br />
efectiv<br />
ã<br />
(m)<br />
Forta<br />
pe<br />
metru<br />
de<br />
lungim<br />
e<br />
(KN)<br />
Forta<br />
cerutã<br />
(KN)<br />
Forta<br />
de<br />
întinde<br />
re<br />
maxim<br />
ã<br />
admisi<br />
bilã<br />
(KN)<br />
Check<br />
(Tmax<br />
>Tr)<br />
E 8,0 25 2,0 4,70 3,30 8,0 16,0 205,26 ok<br />
D 8,0 25 2,0 4,20 3,80 15,0 30,0 236,36 ok<br />
C 8,0 25 2,0 3,70 4,30 20,0 40,0 267,46 ok<br />
B 12,0 32 2,0 3,80 8,20 50,0 100,0 680,06 ok<br />
A 12,0 32 2,0 2,30 9,70 55,0 110,0 804,46 ok<br />
V e rific are la sm ulge re înt re bara de ot e l si m ort ar<br />
Lipsa de aderentã între mortar si teren<br />
Tf= ( D c '+ 2 D K σ v<br />
' tanφ) Le (Forta mobilizata intre mortar si teren)<br />
K = 1 - ( / 90) (1-K ο) = 1 - ( / 90) (sinφ), factor de inclinatie<br />
Granit complet descompus (CDG) cu K = 0.897<br />
T f = ( D c '+ 2 DK σ v<br />
'tanφ) Le = (1.571 + 0.14σ' v<br />
) × Le= (1.571+<br />
0.140 σ' v<br />
)<br />
Tintuiri/Nailings<br />
Zona rezistentã<br />
Adâncimea punctului mediu a lungimii<br />
Lungime efectivã<br />
strat CDG (m)<br />
efective<br />
Strat CDG<br />
Le<br />
CDG<br />
WATER<br />
E 3,30 3,40 0,00<br />
D 3,80 5,30 0,00<br />
C 4,30 7,20 0,00<br />
B 8,20 9,70 1,40<br />
A 9,70 9,40 3,00<br />
Carac t e rist ic i ge om e t ric e ale bare lor de ot e l<br />
Tintuiri/ Tensiune Rezistenta Rezistenta Forta F.O.S. Check<br />
© <strong>GeoStru</strong> <strong>Software</strong>-<strong>Slope</strong> 8.0.1