Rod Eye Digital User Manual - Scanlaser.info
Rod Eye Digital User Manual - Scanlaser.info Rod Eye Digital User Manual - Scanlaser.info
EN 2. Laser Low Battery Warning – The laser icon is displayed when theDE battery of the laser unit is almost depleted. (This feature is laserdependent.)FR3. LED Brightness Indication – Three levels of brightness: (a) bright,IT(b) normal or (c) off – no icon.ES4. Audio Volume Indication – Four levels of volume: (a) loud, (b)PT medium, (c) soft or (d) off – no icon.NL 5. Auto Shutoff Indication – Three shutoff settings: (a) 30 minutes,DA (b) 24 hour or (c) disabled – no icon. (Shutoff settings are onlyNO shown when the detector is turned on or turned off.)SV 6. Units of Measure – Five units of measure: millimeters (mm),FIcentimeters (cm), inches (in), fractions of an inch (inch with fractionbar) or feet (ft).7. Elevation Indication – Numeric value is displayed (dependent onthe unit of measure chosen).• Dashed lines (-- -- -- --) indicate the detector is beyond the rangeto display a numeric value.• In fraction (inch) mode the top number, bottom number and barare used to form a fraction.8. Accuracy Indication – Five levels of accuracy: (a) ultra fine, (b)super fine, (c) fine, (d) medium and (e) coarse.9. Offset on-grade Indication – Indicates the detector bracket isattached to the top mounting hole. More information will be shownabove grade than below grade for special applications.10. Receiver Low Battery Warning – Four levels of battery life aredisplayed: (a) full, (b) batteries low, (c) 30 minutes remaining or (d)empty. (A full battery is only shown when the detector is turned onor turned off.)4 Rod Eye Digital
Detector Bracket {D} inside back cover1. Attachment Knob – Attaches the clamp to the back of the detector.2. Alignment Points – Aligns and secures the clamp.3. Locking Knob – Turn to tighten the locking clamp to the grade rod.4. On-Grade Reference – The top edge of the bar aligns with the ongradeposition.5. Locking Clamp – Moves to tighten onto securely onto grade rods.The clamp reverses for square or oval rods.• (a) Rectangular rods.• (b) Oval / Round rods.To change, remove the screw and turn the clamp over.6. Level Vial – The aids to keep the rod plumb when taking readings.Batteries {E} inside front coverENDEFRITESPTNLDANOSVFIReplace as shown on the picture.Special Features• Strobe Rejection – The RE Digital is designed to reject and eliminateunwanted signals from strobe lights.• Beam Finding – Passing the RE Digital through the laser beam willcause the sensor to beep twice quickly.• Out of Beam Display – If the detector is moved out of the detectorrange, the arrow display will indicate the direction to move to returnto the laser beam.• Laser Low Battery – Alerts the user when the laser’s batteries aregetting low.Rod Eye Digital5
- Page 1 and 2: Rod Eye DigitalUser ManualVersion 1
- Page 3: EnglishDeutschFrançaisItalianoEspa
- Page 7: Keypad Operation {B} inside front c
- Page 11 and 12: Menu Functions (continued)• DRO D
- Page 13 and 14: Areas of responsibilityResponsibili
- Page 15: Technical DataWorking Radius (laser
- Page 18 and 19: ENDEFRITESPTNLDANOSVFIGrundlegende
- Page 20 and 21: ENDEFRITESPTNLDANOSVFILCD-Anzeige {
- Page 22 and 23: SonderbetriebsmodiENDEFR Messwert h
- Page 24 and 25: ENDEFRITESPTNLDANOSVFIPflege und Tr
- Page 26 and 27: ENDEFRITESPTNLDANOSVFIbereit oder k
- Page 29 and 30: Manuel de l'utilisateurFrançaisCe
- Page 31 and 32: Touches {B}, au verso de la couvert
- Page 33 and 34: Fixation du détecteur {D}, au rect
- Page 35 and 36: Fonctions Menu (suite)• DRO Lectu
- Page 37 and 38: ResponsabilitéResponsabilité du f
- Page 39: Caractéristiques techniquesRayon d
- Page 45 and 46: 10. Stato della batteria del ricevi
- Page 47 and 48: Funzioni di menu (continuazione)•
- Page 49 and 50: Ambiti di responsabilitàResponsabi
- Page 51: Dati tecniciRaggio di lavoro (dipen
- Page 54 and 55: Principios básicos de operación {
- Page 56 and 57: EN • Fuera de visualización de r
Detector Bracket {D} inside back cover1. Attachment Knob – Attaches the clamp to the back of the detector.2. Alignment Points – Aligns and secures the clamp.3. Locking Knob – Turn to tighten the locking clamp to the grade rod.4. On-Grade Reference – The top edge of the bar aligns with the ongradeposition.5. Locking Clamp – Moves to tighten onto securely onto grade rods.The clamp reverses for square or oval rods.• (a) Rectangular rods.• (b) Oval / Round rods.To change, remove the screw and turn the clamp over.6. Level Vial – The aids to keep the rod plumb when taking readings.Batteries {E} inside front coverENDEFRITESPTNLDANOSVFIReplace as shown on the picture.Special Features• Strobe Rejection – The RE <strong>Digital</strong> is designed to reject and eliminateunwanted signals from strobe lights.• Beam Finding – Passing the RE <strong>Digital</strong> through the laser beam willcause the sensor to beep twice quickly.• Out of Beam Display – If the detector is moved out of the detectorrange, the arrow display will indicate the direction to move to returnto the laser beam.• Laser Low Battery – Alerts the user when the laser’s batteries aregetting low.<strong>Rod</strong> <strong>Eye</strong> <strong>Digital</strong>5