D21805 Euro man percussion drill_JL.indd - Service - DeWalt
D21805 Euro man percussion drill_JL.indd - Service - DeWalt
D21805 Euro man percussion drill_JL.indd - Service - DeWalt
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ENGLISH<br />
● Put the chuck key (10) into each hole in the<br />
side of the chuck and turn clockwise until tight.<br />
● To remove the bit, proceed in reverse order.<br />
Fitting the Side Handle (fig. A)<br />
The side handle (6) can be fi tted to suit both RHand<br />
LH-users.<br />
WARNING: Always use the <strong>drill</strong> with the<br />
side handle properly assembled.<br />
● Loosen the side handle.<br />
● For RH-users, slide the side handle clamp over<br />
the collar behind the chuck, handle at the left.<br />
● For LH-users, slide the side handle clamp over<br />
the colar behind the chuck, handle at the right.<br />
● Rotate the side handle to the desired position<br />
and tighten the handle.<br />
Setting the Drilling Depth (fig. C)<br />
● Insert the required <strong>drill</strong> bit into the chuck.<br />
● Slacken the side handle (6).<br />
● Fit the depth adjustment rod (7) through the<br />
hole in the side handle clamp.<br />
● Adjust the <strong>drill</strong>ing depth as shown.<br />
● Tighten the side handle.<br />
Forward/reverse Slider (fig. A)<br />
● To select forward or reverse rotation, use the<br />
forward/reverse-switch (3) (see arrow on tool).<br />
WARNING: Always wait until the motor<br />
has come to a complete standstill<br />
before changing the direction of<br />
rotation.<br />
Two Gear Selector (fig. E)<br />
Your tool is fi tted with a two gear selector (4) to<br />
vary the speed/torque ratio.<br />
● Release the variable speed switch and select<br />
the required position. This can be done either<br />
with the tool switched off or running under no<br />
load condition.<br />
Always align the selector with the arrow on the<br />
gear housing:<br />
1 low speed/high torque<br />
(<strong>drill</strong>ing large holes, driving large screws)<br />
2 high speed/low torque<br />
(<strong>drill</strong>ing smaller holes, <strong>drill</strong>ing in wood)<br />
For information on speed rates, refer to the<br />
technical data.<br />
● Do not change gears at full speed or during<br />
use.<br />
Chuck Removal (fig. F, G)<br />
● Open the chuck jaws as far as possible.<br />
● Insert a screwdriver into the chuck and remove<br />
the chuck retaining screw (12) by turning<br />
clockwise.<br />
● Tighten an Allen key into the chuck and strike it<br />
with a hammer as shown.<br />
Prior to Operation<br />
• Insert the appropriate bit.<br />
• Mark the spot where the hole is to be <strong>drill</strong>ed.<br />
OPERATION<br />
WARNING: To reduce the risk<br />
of serious personal injury, turn<br />
tool off and disconnect tool from<br />
power source before making any<br />
adjustments or removing/installing<br />
attachments or accessories.<br />
Instructions for Use<br />
WARNING: Always observe the safety<br />
instructions and applicable regulations.<br />
● Be aware of the location of pipework<br />
and wiring.<br />
● Apply only a gentle pressure to the tool.<br />
Excessive force does not speed up<br />
<strong>drill</strong>ing but decreases tool perfor<strong>man</strong>ce<br />
and may shorten tool life.<br />
Proper Hand Position (fig. A, B)<br />
WARNING: To reduce the risk of serious<br />
personal injury, ALWAYS use proper<br />
hand position as shown.<br />
WARNING: To reduce the risk of serious<br />
personal injury, ALWAYS hold securely in<br />
anticipation of a sudden reaction.<br />
Proper hand position requires one hand on the side<br />
handle (6), with the other hand on the main handle<br />
(11).<br />
Switching On and Off (fig. A)<br />
● To run the tool, press the variable speed switch<br />
(1). The pressure exerted on the variable speed<br />
switch determines the tool speed.<br />
27