CG40EK (LP) CG40EYA (TP) - Hitachi

More documents

Recommendations

Info

Fig.1-1 Fig.1-2 Fig.1-3 Fig.1-3B Fig.1-3C Fig.1-3D 3. Assembly procedures Drive shaft to engine (Fig. 1-1) Attach the engine to the clutch case (2) with the four screws or bolts (1) provided. Installation of handle (Fig. 1-2) Attach the handle to the drive shaft tube with the angle towards the engine. Adjust the location to the most comfortable position but not too close to power head before operation. Installation of handle (Fig. 1-3, 3B) Remove the handle bracket (1) from the assembly. (Fig. 1-3) Place the handles and attach the handle bracket with four bolts lightly. Adjust to appropriate position. Then fix it firmly with the bolts. Unhook the hip pad and wrap the tubed stop cords and throttle wire (1) with it. (Fig. 1-3B) NOTE for <strong>CG40EYA</strong> (<strong>TP</strong>) (Fig. 1-3C, 3D) The drive shaft and the engine of this model are pre-assembled at the factory. All you have to do is attach throttle grip on the handle with a screw and a nut and then install it on the handle brackets. Finger-tighten the knob nut securely. GB-7
Fig. 1-4 Fig. 1-5 Fig. 1-6 Throttle wire / stop cord Remove air cleaner cover. (Fig. 1-4) Connect stop cords. (Fig. 1-5) Connect throttle wire end to carburetor. (Fig.1-5) Cover throttle wire and stop cords together with protective tube provided up to air cleaner cover. (Fig. 1-6) Installation of blade guard (Fig. 1-8) NOTE! The guard bracket may come already mounted to the gear case on some models. Install the blade guard on drive shaft tube against angle transmission. Tighten the guard bracket firmly so that the blade guard does not swing or move down during operation. CAUTION! Some blade guards are equipped with sharp line limiters. Be careful with handling it. GB-8
Page 1 and 2: CG40EK (LP) CG40EYA (TP) Owner's ma
Page 3 and 4: Meanings of symbols or labels. (NOT
Page 5 and 6: Declaration of conformity We, Nikko
Page 7: 2. Warnings and safety instructions
Page 11 and 12: Fig. 1-10 Fig. 1-10B 5 17cm 17cm CH
Page 13 and 14: Fig. 2-4 Fig. 2-4B Fig. 2-4C 15m Fi
Page 15 and 16: Fig. 3-4 Fig. 3-5 Fig. 3-5B 1 2 R1-
Page 17 and 18: 6. Specifications MODEL CG40EK (LP)
Page 19 and 20: Betydelser av Symboler eller etiket
Page 21 and 22: vi,Nikko Tanaka Engineering Co., Lt
Page 23 and 24: 2. Varning och säkerhets-anvisning
Page 25 and 26: Fig. 1-4 Fig. 1-5 Fig. 1-6 Gasspjal
Page 33 and 34: 6. Tekniska data MODELL CG40EK (LP)
Page 35 and 36: Betydning af symboler og mærker. (
Page 37 and 38: Overensstemmelseserklæring Vi, Nik
Page 39 and 40: 2. Advarsler og sikkerhedsinstrukti
Page 41 and 42: Fig. 1-4 Fig. 1-5 Fig. 1-6 Kabel ti
Page 49 and 50: 6. Specifikationer MODEL CG40EK (LP
Page 51 and 52: Betydning av symboler og etiketter.
Page 53 and 54: Konformitetserklæring Vi, Nikko Ta
Page 55 and 56: 2. Advarsler og sikkerhetsinstruksj
Page 57 and 58: Fig. 1-4 Fig. 1-5 Fig. 1-6 Gass-st
Page 59 and 60:
Fig. 1-10 Fig. 1-10B 5 17cm 17cm CH
Page 61 and 62:
Fig. 2-4 Fig. 2-4B Fig. 2-4C 15m Fi
Page 63 and 64:
Fig. 3-4 Fig. 3-5 Fig. 3-5B 1 2 R1-
Page 65 and 66:
6. Tekniske data MODEL CG40EK (LP)
Page 67 and 68:
Symbolien tai tarrojen merkitys. (H
Page 69 and 70:
Vaatimustenmukaisuusilmoitus Me,Nik
Page 71 and 72:
2. Varoitukset ja turvallisuusohjee
Page 73 and 74:
kuva. 1-4 kuva. 1-5 kuva. 1-6 Kaasu
Page 75 and 76:
kuva. 1-10 kuva. 1-10B 5 17cm 17cm
Page 77 and 78:
kuva. 2-4 kuva. 2-4B kuva. 2-4C 15m
Page 79 and 80:
kuva. 3-4 kuva. 3-5 kuva. 3-5B 1 2
Page 81 and 82:
6. Tekniset tiedot MODEL CG40EK (LP
Page 83 and 84:
15m 50FT 15m 50FT
Page 85 and 86:
5 6 7 11 13 15 RU-4
Page 87 and 88:
RU-6
Page 89 and 90:
RU-8
Page 91 and 92:
5 17cm 17cm CH-100
Page 93 and 94:
15m
Page 95 and 96:
1 2 R1-1.5 mm 1.9-2.2 mm
Page 97 and 98:
MODEL CG40EK (LP) CG40EYA (TP)
show all

CG40EK (LP) CG40EYA (TP) - Hitachi

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?