KM 90/45 R - Kärcher
KM 90/45 R - Kärcher KM 90/45 R - Kärcher
sweeping pattern of Check main brush the Raise the sweep roller Raise the side broom Drive the sweeper on a flat and floor noticeably covered smooth dust or chalk with Lower the main brush and rotate briefly it Raise the sweep roller Depress pedal to raise the flap and keep it coarse-dirt depressed Back the machine away form of the sweeping pattern The a regular rectangle, that is forms Note: Due to the floating suspension of — main brush The sweeping the automatically adapts itself pattern The main brush must be replaced — and replacing Adjusting strips sealing Stand sweeper on a flat surface Raise the sweep roller Turn key switch to "0" and key remove Secure the machine against away using a wedge rolling Remove the debris container both sides of the unit from Slightly unscrew fastening of sealing strip; screw it off to front it replace Screw on new sealing strip but Align the sealing strip Set the sealing strip’s clearance the floor so that it bends to with a lag of backwards - 15 mm 10 Tighten nuts Insert the swept material container Slightly unscrew fastening of rear strip; screw it off to sealing it replace Screw on new sealing strip but Align the sealing strip Set the sealing strip’s clearance the floor so that it bends to with a lag of backwards - 15 mm 10 Tighten the screws Fit the sweeping drum Insert the swept material Screw off side panelling on both sides Unscrew front screw of side panelling Unscrew rear screws of side panelling Slightly unscrew fastening of sealing strip; unscrew it off lateral replace it to Screw on new sealing strip but Operating instructions KM 90/45 R English Front sealing strip container Side sealing strips Rear sealing strip between 50 - 70 mm wide. do not yet tighten nuts do not yet tighten the screws to wear of the bristles. when the bristles are too worn. do not yet tighten the screws 30
Slide in a spacer with a max. of 3 mm in order to thickness clearance to floor adjust Align the sealing strip so that the to the floor is a uniform clearance - 3 mm 0 Screw on side panelling Insert the swept material Danger! First dedust the filter and then briefly until the dust has wait before opening the the settled cover. filter Wear a dust protection mask working on the filter system when Observe the safety precautions Tilt the filter cover and the seat forward Manually depress filter cover and 4 screws with star grip unscrew Close filter box lid, screw it tight tilt back filter cover and Note: sure when mounting the new Make that the lamella are not filter damaged Unit cover seal 1. Filter box tunnel seal 2. Danger! engine takes approx. 3...4 s to The down after being shut off. run enter operating area during Never Turn key switch to "0" and key remove Inspect traction belt for tightness, and damage wear Operating instructions KM 90/45 R English Replace the dust filter Replacing unit cover seals Checking traction belt this period! for handling fine dust Tilt filter box lid forward Dust filter cover seal Tighten the screws container Replace lamellar filter Side brush round belt Main brush V-belt 31
- Page 1 and 2: KM 90/45 R 1.405-101 1.405-111 www.
- Page 3 and 4: Ihrer Sicherheit! 4 Zu Hinweise 4 A
- Page 5 and 6: Zur Vermeidung von — — Keine
- Page 7 and 8: Achtung! Gerät darf nur betrieben
- Page 9 and 10: Achtung! Maschine muss beim Transpo
- Page 11 and 12: Hersteller/Kärcher-Bestell-Nr. Bes
- Page 13 and 14: Heckblende demontieren Befestigung
- Page 15 and 16: Dichtleiste ausrichten Bodenabstan
- Page 17 and 18: fährt nicht Maschine Fahrpedal nic
- Page 19 and 20: your own safety! 20 For notes 20 Ge
- Page 21 and 22: features are provided for the Safet
- Page 23 and 24: the driving direction at the Select
- Page 25 and 26: y the Maintenance customer maintena
- Page 27 and 28: Note: using batteries with a liquid
- Page 29: for lowering side Stop brush the si
- Page 33 and 34: data Unit x width x height Length x
- Page 35 and 36: lire absolument avant A de l'appare
- Page 37 and 38: la première mise en Avant service
- Page 39 and 40: le rouleau de balayage Lever Tirer
- Page 41 and 42: le capot de la Ouvrir/fermer machin
- Page 43 and 44: chargement peut être contrôlé à
- Page 45 and 46: le rouleau Changer balayeur Le remp
- Page 47 and 48: Appuyer vers le bas à la main sur
- Page 49 and 50: de l'appareil Vibrations globale de
- Page 51 and 52: attentamente prima Leggere dell‘a
- Page 53 and 54: Spina di alimentazione 1. (variante
- Page 55 and 56: il rullo spazzatore Sollevare Tirar
- Page 57 and 58: Arrestare la spazzatrice su una pi
- Page 59 and 60: il cavo di Collegare alla batteria
- Page 61 and 62: abbassamento Arresto laterale spazz
- Page 63 and 64: Allentare leggermente il fissaggio
- Page 65 and 66: tecnici dell’apparecchio Dati x l
- Page 67 and 68: gebruik van het apparaat Voor lezen
- Page 69 and 70: Netstekker laadapparaat 1. (package
- Page 71 and 72: optillen Veegwals Hendel naar boven
- Page 73 and 74: Apparaatkap openen/sluiten Handschr
- Page 75 and 76: laden kan via de laadindicatie Het
- Page 77 and 78: Vervanging is noodzakelijk als —
- Page 79 and 80: Filterkastdeksel naar voren klappe
sweeping pattern of<br />
Check<br />
main brush<br />
the<br />
Raise the sweep roller<br />
<br />
Raise the side broom<br />
<br />
Drive the sweeper on a flat and<br />
<br />
floor noticeably covered<br />
smooth<br />
dust or chalk<br />
with<br />
Lower the main brush and rotate<br />
<br />
briefly it<br />
Raise the sweep roller<br />
<br />
Depress pedal to raise the<br />
<br />
flap and keep it<br />
coarse-dirt<br />
depressed<br />
Back the machine away<br />
<br />
form of the sweeping pattern<br />
The<br />
a regular rectangle, that is<br />
forms<br />
Note:<br />
Due to the floating suspension of<br />
—<br />
main brush The sweeping<br />
the<br />
automatically adapts itself<br />
pattern<br />
The main brush must be replaced<br />
—<br />
and replacing<br />
Adjusting<br />
strips<br />
sealing<br />
Stand sweeper on a flat surface<br />
<br />
Raise the sweep roller<br />
<br />
Turn key switch to "0" and<br />
<br />
key<br />
remove<br />
Secure the machine against<br />
<br />
away using a wedge<br />
rolling<br />
Remove the debris container<br />
<br />
both sides of the unit<br />
from<br />
Slightly unscrew fastening of<br />
<br />
sealing strip; screw it off to<br />
front<br />
it replace<br />
Screw on new sealing strip but<br />
<br />
Align the sealing strip<br />
<br />
Set the sealing strip’s clearance<br />
<br />
the floor so that it bends<br />
to<br />
with a lag of<br />
backwards<br />
- 15 mm<br />
10<br />
Tighten nuts<br />
<br />
Insert the swept material<br />
<br />
container<br />
Slightly unscrew fastening of rear<br />
<br />
strip; screw it off to<br />
sealing<br />
it replace<br />
Screw on new sealing strip but<br />
<br />
Align the sealing strip<br />
<br />
Set the sealing strip’s clearance<br />
<br />
the floor so that it bends<br />
to<br />
with a lag of<br />
backwards<br />
- 15 mm<br />
10<br />
Tighten the screws<br />
<br />
Fit the sweeping drum<br />
<br />
Insert the swept material<br />
<br />
Screw off side panelling on both<br />
<br />
sides<br />
Unscrew front screw of side<br />
<br />
panelling<br />
Unscrew rear screws of side<br />
<br />
panelling<br />
Slightly unscrew fastening of<br />
<br />
sealing strip; unscrew it off<br />
lateral<br />
replace it<br />
to<br />
Screw on new sealing strip but<br />
<br />
Operating instructions <strong>KM</strong> <strong>90</strong>/<strong>45</strong> R English<br />
Front sealing strip<br />
container<br />
Side sealing strips<br />
Rear sealing strip<br />
between 50 - 70 mm wide.<br />
do not yet tighten nuts<br />
do not yet tighten the screws<br />
to wear of the bristles.<br />
when the bristles are too worn.<br />
do not yet tighten the screws<br />
30