You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
1 609 929 894 - Buch Seite 3 Mittwoch, 1. Oktober 2003 9:10 09<br />
Operating Instructions<br />
The wear of the impact striker is reduced when<br />
blank shots are avoided, and the work is not always<br />
carried out with the maximum hammer<br />
force.<br />
Safety Cover<br />
When the safety cover 7 is in the rear position,<br />
plane-parallel working is possible.<br />
Always slide the safety cover 7 over the tacker<br />
head 6 while pausing, after the work, as well as<br />
during transport and storage of the machine.<br />
Clamps for Profiled Wood or Grooves<br />
For fastening of ceiling panelling with clamps for<br />
profiled wood or grooves, only resin-covered<br />
staples with a length of <strong>19</strong> mm may be used.<br />
Hold the machine sloped at an angle of<br />
approx. 30° and press it centrally against the profiled<br />
wood clamp or groove clamp.<br />
mikosoft praha s.r.o.<br />
Fire off a test shot to determine whether or not the<br />
clamp is tacked sufficiently firm against the structural<br />
material with the selected hammer force adjustment.<br />
At the tacking location, the clamps for profiled<br />
wood or grooves may not have stiffening ribs.<br />
The ribs prevent the clamps from penetrating<br />
completely and damage the impact striker.<br />
Tacking of Wooden Laths/Strips<br />
When tacking laths/strips, begin working with a<br />
low hammer force adjustment. Otherwise traces<br />
of the impact striker can result on the surface.<br />
mikosoft praha s.r.o.<br />
10 • 1 609 929 894 • TMS • 26.09.03<br />
English - 3<br />
Seized Staples<br />
■ Before any work on the machine itself, pull<br />
the mains plug.<br />
The staples can seize up inside of the tacker<br />
head 6 e. g., when running into a hidden screw.<br />
They can be removed as follows:<br />
Remove the magazine slider 8.<br />
Loosen the screws 4. Pull away the face plate 5<br />
downwards and remove jammed or stuck staples.<br />
Reinsert the face plate 5 again. When inserting<br />
the face plate 5, pay attention that it<br />
closes off flush with the tacker head 6. Tighten<br />
the screws 4 again.<br />
Intermittent Operation<br />
The machine is designed for intermittent operation<br />
only. It heats up in continuous operation. The<br />
tacking force is reduced with increasing heating<br />
up.<br />
Pause after a maximum of 15 minutes and allow<br />
the machine to cool off.<br />
mikosoft praha s.r.o.<br />
Extension Cable<br />
In order to avoid a capacity reduction of the impact<br />
force, use an extension cable with a cross<br />
section of at least 1.5 mm 2 and a maximum<br />
length of 10 metres.<br />
Always unroll the cable drum completely.<br />
Maintenance and Cleaning<br />
■ Before any work on the machine itself, pull<br />
the mains plug.<br />
For safe and proper working, always keep<br />
☞ the machine and the ventilation slots clean.<br />
If the machine should fail despite the care taken<br />
in manufacturing and testing procedures, repair<br />
should be carried out by an after-sales service<br />
centre for Bosch power tools.<br />
In all correspondence and spare parts orders,<br />
please always include the 10-digit order number<br />
given on the nameplate of the machine.<br />
mikosoft praha s.r.o.
Change language