KMR 1700 D - Kärcher
KMR 1700 D - Kärcher KMR 1700 D - Kärcher
Operating Instructions KMR 1700 D English Pull-out the oil dip rod — The oil level must be between the "Min" and the "Max" marks. — Top up the engine oil if the oil level is below the "Min" mark. — Do not fill up beyond "Max" Danger! Danger of burns! Let the engine cool-down Release the cap screw of the oilfilling opening Fill-in engine oil Oil types: See technical data Close the oil fill opening Wait at least 5 Min Check the engine oil level Replace engine oil and oil filter Engine oil replacement Provide a collecting container for at least 4 litres of oil Screw-off the drain screw in the anticlockwise direction Danger! Risk of burning if oil is hot It is essential to fit a new gasket when screwing-in the drain screw again Tighten drain plug with a torque wrench to 25 Nm Oil filter replacement Screw-off the oil filter in the anticlockwise direction Clean the supporting and sealing surfaces Wet the gasket of the new oil filter with oil before mounting Hand-tighten new oil filter Check the hydraulic oil level Open the rear engine covering Check hydraulic oil level in the top right inspection glass Notes: The hydraulic oil level must be between the "Min" and "Max" marks. See the chapter on replenishing hydraulic oil if the hydraulic oil level is below the "Min" mark. Close the rear engine cover Top-up with hydraulic oil Release the driver’s seat and pull it out downwards Unscrew 4 screws at the inspection cover Unscrew oil filler hole cap Warning! Keep oil filler hole clean 36
Operating Instructions KMR 1700 D English Pull out hydraulic oil filter Top-up with hydraulic oil Oil type: see label on the hydraulic oil container or "Technical Data" Note: Open the rear engine covering Check replenished amount at the inspection glass Note: The hydraulic oil level must be between the "Min" and "Max" marks. Screw on oil filler hole cap Screw tight inspection cover with 4 screws Mount driver’s seat Close the rear engine cover Check hydraulic system Check all hydraulic hoses and connections to make sure that they are not leaking Check degree of contamination of the hydraulic oil filter Lock the hand brake Open rear engine cowl with the unit key Start engine Check the degree of contamination of the hydraulic oil filter Notes: If the indicator on the hydraulic oil return manometer is in the red area, the hydraulic oil filter must be cleaned or replaced Please consult the Kärcher after sales service for maintenance of the hydraulics Check and overhaul the water cooler Danger! Danger of scalding due to boiling water! Let cooler cool off at least 20 Min. Check the cooling water level Open the engine bonnet Open the cooler pressure flap Note: The cooling water should reach to the bottom edge of the filling connector Top up coolant as far as bottom edge of filler neck Note: The cooling water must not contain more than 50% anti-freeze agent! Clean the cooler vanes Check the cooler hoses and connections for any leaks Clean the fan 37
- Page 1 and 2: KMR 1700 D 1.186-114.0 www.karcher.
- Page 3 and 4: Betriebsanleitung KMR 1700 D Deutsc
- Page 5 and 6: Betriebsanleitung KMR 1700 D Deutsc
- Page 7 and 8: Betriebsanleitung KMR 1700 D Deutsc
- Page 9 and 10: Betriebsanleitung KMR 1700 D Deutsc
- Page 11 and 12: Betriebsanleitung KMR 1700 D Deutsc
- Page 13 and 14: Betriebsanleitung KMR 1700 D Deutsc
- Page 15 and 16: Betriebsanleitung KMR 1700 D Deutsc
- Page 17 and 18: Betriebsanleitung KMR 1700 D Deutsc
- Page 19 and 20: Betriebsanleitung KMR 1700 D Deutsc
- Page 21 and 22: Betriebsanleitung KMR 1700 D Deutsc
- Page 23 and 24: Betriebsanleitung KMR 1700 D Deutsc
- Page 25 and 26: Betriebsanleitung KMR 1700 D Deutsc
- Page 27 and 28: Operating Instructions KMR 1700 D E
- Page 29 and 30: Operating Instructions KMR 1700 D E
- Page 31 and 32: Operating Instructions KMR 1700 D E
- Page 33 and 34: Operating Instructions KMR 1700 D E
- Page 35: Operating Instructions KMR 1700 D E
- Page 39 and 40: Operating Instructions KMR 1700 D E
- Page 41 and 42: Operating Instructions KMR 1700 D E
- Page 43 and 44: Operating Instructions KMR 1700 D E
- Page 45 and 46: Operating Instructions KMR 1700 D E
- Page 47 and 48: Operating Instructions KMR 1700 D E
- Page 49 and 50: Notice d'utilisation KMR 1700 D Fra
- Page 51 and 52: Notice d'utilisation KMR 1700 D Fra
- Page 53 and 54: Notice d'utilisation KMR 1700 D Fra
- Page 55 and 56: Notice d'utilisation KMR 1700 D Fra
- Page 57 and 58: Notice d'utilisation KMR 1700 D Fra
- Page 59 and 60: Notice d'utilisation KMR 1700 D Fra
- Page 61 and 62: Notice d'utilisation KMR 1700 D Fra
- Page 63 and 64: Notice d'utilisation KMR 1700 D Fra
- Page 65 and 66: Notice d'utilisation KMR 1700 D Fra
- Page 67 and 68: Notice d'utilisation KMR 1700 D Fra
- Page 69 and 70: Notice d'utilisation KMR 1700 D Fra
- Page 71 and 72: Notice d'utilisation KMR 1700 D Fra
- Page 73 and 74: Notice d'utilisation KMR 1700 D Fra
- Page 75 and 76: Istruzioni per l'uso KMR 1700 D Ita
- Page 77 and 78: Istruzioni per l'uso KMR 1700 D Ita
- Page 79 and 80: Istruzioni per l'uso KMR 1700 D Ita
- Page 81 and 82: Istruzioni per l'uso KMR 1700 D Ita
- Page 83 and 84: Istruzioni per l'uso KMR 1700 D Ita
- Page 85 and 86: Istruzioni per l'uso KMR 1700 D Ita
Operating Instructions <strong>KMR</strong> <strong>1700</strong> D English<br />
Pull out hydraulic oil filter<br />
Top-up with hydraulic oil<br />
Oil type: see label on the<br />
hydraulic oil container or<br />
"Technical Data"<br />
Note:<br />
Open the rear engine covering<br />
Check replenished amount at the<br />
inspection glass<br />
Note:<br />
The hydraulic oil level must be<br />
between the "Min" and "Max" marks.<br />
Screw on oil filler hole cap<br />
Screw tight inspection cover with<br />
4 screws<br />
Mount driver’s seat<br />
Close the rear engine cover<br />
Check hydraulic system<br />
Check all hydraulic hoses and<br />
connections to make sure that<br />
they are not leaking<br />
Check degree of contamination<br />
of the hydraulic oil filter<br />
Lock the hand brake<br />
Open rear engine cowl with the<br />
unit key<br />
Start engine<br />
Check the degree of<br />
contamination of the hydraulic oil<br />
filter<br />
Notes:<br />
If the indicator on the hydraulic oil<br />
return manometer is in the red area,<br />
the hydraulic oil filter must be<br />
cleaned or replaced<br />
Please consult the <strong>Kärcher</strong> after<br />
sales service for maintenance of the<br />
hydraulics<br />
Check and overhaul the<br />
water cooler<br />
Danger!<br />
Danger of scalding due to boiling<br />
water!<br />
Let cooler cool off at least<br />
20 Min.<br />
Check the cooling water level<br />
Open the engine bonnet<br />
Open the cooler pressure flap<br />
Note:<br />
The cooling water should reach to<br />
the bottom edge of the filling<br />
connector<br />
Top up coolant as far as bottom<br />
edge of filler neck<br />
Note:<br />
The cooling water must not contain<br />
more than 50% anti-freeze agent!<br />
Clean the cooler vanes<br />
Check the cooler hoses and<br />
connections for any leaks<br />
Clean the fan<br />
37