Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ENGLISH<br />
36<br />
Support long workpieces using any convenient means such as sawhorses<br />
or similar devices to keep the ends from dropping.<br />
Consult your dealer for further information on the appropriate accessories.<br />
Transporting (fi g. B)<br />
• To transport the saw, lower the head and depress the lock down pin<br />
(17).<br />
• Lock the table (19) into lowest position. Lock the rail lock knob with<br />
the saw head in the front position, lock the mitre arm in the far right<br />
mitre angle, slide the fence (13) completely inward and lock the bevel<br />
lever (15) with the saw head in the vertical position to make the tool<br />
as compact as possible.<br />
• Always use the hand indentations (26) shown in fi g. B to transport<br />
the saw.<br />
Always transport the machine in saw bench mode with the<br />
upper blade guard fi tted. Never carry the machine by the<br />
guard.<br />
Maintenance<br />
Your D E WALT power tool has been designed to operate over a long<br />
period of time with a minimum of maintenance. Continuous satisfactory<br />
operation depends upon proper tool care and regular cleaning.<br />
• If the saw blade does not stop in less than 10 seconds after switching<br />
off, have the machine serviced by an authorised D E WALT repair<br />
agent.<br />
Prior to maintenance always unplug the tool.<br />
Cleaning<br />
Keep the ventilation slots clear and regularly clean the housing with<br />
a soft cloth.<br />
• Regularly clean the table top.<br />
Avoid the use of cleaners or lubricants to maintain the tool. In<br />
particular spray and aerosol cleaners may chemically attack<br />
the plastic lower guard.<br />
Cleaning and maintaining the kerf plate (fi g. U)<br />
Regularly clean the area below the kerf plate.<br />
If the kerf plate is worn it must be replaced.<br />
• Remove the screws (74) holding the kerf plate (8).<br />
• Remove the kerf plate and clean the area below.<br />
• Re-install the parts of the kerf plate and the screws.<br />
• Tighten the screws hand-tight.<br />
• To adjust the kerf plate, proceed as follows:<br />
• Pull down the head until the blade just enters the saw kerf.<br />
• Adjust each part of the kerf plate to fi t closely to the teeth of the blade.<br />
• Tighten the screws.<br />
L ubrication<br />
This machine requires no additional lubrication. The bearings of the<br />
motor are pre-lubricated and watertight.<br />
• Avoid using oil or grease as this can cause clogging with sawdust<br />
and chips and create problems.<br />
• Clean the parts subject to accumulation of sawdust and chips<br />
periodically with a dry brush.<br />
Protecting the environment<br />
Separate collection. This product must not be disposed of<br />
with normal household waste.<br />
Should you fi nd one day that your D E WALT product needs replacement,<br />
or if it is of no further use to you, do not dispose of it with household<br />
waste. Make this product available for separate collection.<br />
Separate collection of used products and packaging allows<br />
materials to be recycled and used again. Re-use of recycled<br />
materials helps prevent environmental pollution and reduces<br />
the demand for raw materials.<br />
Local regulations may provide for separate collection of electrical<br />
products from the household, at municipal waste sites or by the retailer<br />
when you purchase a new product.<br />
D E WALT provides a facility for the collection and recycling of D E WALT<br />
products once they have reached the end of their working life. To take<br />
advantage of this service please return your product to any authorised<br />
repair agent who will collect them on our behalf.<br />
You can check the location of your nearest authorised repair agent by<br />
contacting your local D E WALT offi ce at the address indicated in this<br />
manual. Alternatively, a list of authorised D E WALT repair agents and full<br />
details of our after-sales service and contacts are available on the<br />
Internet at: www.2helpU.com<br />
GUARANTEE<br />
• 30 DAY NO RISK SATISFACTION GUARANTEE •<br />
If you are not completely satisfi ed with the performance of your<br />
D E WALT machine, simply return it within 30 days, complete as<br />
purchased, to the point of purchase, for a full refund or exchange.<br />
Proof of purchase must be produced.<br />
• ONE YEAR FREE SERVICE CONTRACT •<br />
If you need maintenance or service for your D E WALT machine, in the<br />
12 months following purchase, it will be undertaken free of charge at<br />
an authorized D E WALT repair agent. Proof of purchase must be<br />
produced. Includes labour and spare parts for Power Tools.<br />
Excludes accessories.<br />
• ONE YEAR WARRANTY •<br />
If your D E WALT product becomes defective due to faulty materials or<br />
workmanship within 12 months from the date of purchase,<br />
we guarantee to replace all defective parts free of charge or, at our<br />
discretion, replace the unit free of charge provided that:<br />
• The product has not been misused.<br />
• Repairs have not been attempted by unauthorized persons.<br />
• Proof of purchase date is produced.<br />
This guarantee is offered as an extra benefi t and is additional to<br />
consumers statutory rights.<br />
For the location of your nearest authorized D E WALT repair agent,<br />
please use the appropriate telephone number on the back of this<br />
manual. Alternatively, a list of authorized D E WALT repair agents and<br />
full details on our after-sales service are available on the Internet at<br />
www.2helpU.com .