Download of Print - Kusters
Download of Print - Kusters
Download of Print - Kusters
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
9<br />
Failure and analysis<br />
Note: When replacing the controller, make sure insert the wire jumper into the new controller, otherwise the<br />
unit display C5 and can't be turned on(only for 9k,12k)<br />
Note: When replacing the controller, make sure insert the wire jumper into the new controller, otherwise the running indicator<br />
turns <strong>of</strong>f 3s and blink 15 times (the dual eight will display C5) but cannot turn on the unit£¨£only for 18k,24k©.<br />
The breaker trips at once when it<br />
is set to "ON".<br />
Measure insulation resistance to ground to see<br />
if there is any leakage.<br />
Trip <strong>of</strong> breaker or blow<br />
<strong>of</strong> fuse<br />
The circuit or the part <strong>of</strong> the air conditioner has<br />
The breaker trips in few minutes<br />
when it is set to "ON"<br />
malfunction. They heat and break the insulation<br />
and lead to short circuit or creepage. Measure<br />
the insulation resistance or eliminate the malfunction<br />
one by one. If the breaker itself has<br />
malfunction, then replace the breaker.<br />
No power<br />
Check power supply circuit.<br />
Air conditioner can not start up<br />
The air conditioner<br />
does not react after<br />
it is powered ( after<br />
the plug is inserted,<br />
the buzzer does<br />
not sound and the<br />
remote startup has<br />
no response)<br />
Power plug is not well plugged in and poor connection<br />
Fuse <strong>of</strong> controller burnt out<br />
The transformer connection is loose or has bad<br />
contact or the transformer has malfunction<br />
Controller is broken<br />
Check if the plug is properly plugged in and<br />
make the loose contact firm.<br />
Change controller fuse<br />
Fasten the wiring; measure the output<br />
v o l t a g e o f t h e t r a n s f o r m e r , i f i t i s<br />
incorrect, change the transformer<br />
Check remote controller<br />
The remote controller<br />
Remote controller is short <strong>of</strong> power<br />
Change batteries<br />
does not receive<br />
signals (after it is<br />
powered, the buzzer<br />
will sound, unless it<br />
has malfunction)<br />
Remote controller malfunction<br />
Receiver loose or poor connection<br />
First, press the manual switch button AUTO,<br />
if there is no response,check based on the<br />
above methods. If it runs normally after<br />
pressing the button,check again whether the<br />
installation position and the connection wire<br />
<strong>of</strong> the reception head is correct. If it is<br />
Receiver is broken<br />
correct,then replace the receiver or the remote<br />
controller.<br />
Power voltage is too low<br />
heck the voltage. If it is lower than 10£¥ <strong>of</strong> the rated voltage, check the<br />
cause, improve the power supply condition and add the stabilized voltage<br />
power supply.<br />
C o n t r o l l e r m a l f u n c t i o n ( I C 2 0 0 3 b r o k e n ,<br />
creepage <strong>of</strong> parallel capacitor <strong>of</strong> relay loop,<br />
relay is broken etc.)<br />
Change controller<br />
In cool, heat mode,the<br />
outdoor<br />
unit and compressor<br />
will not run.<br />
Wire loose or wrong connection<br />
Improper setting <strong>of</strong> temperature<br />
Correctly wire according to the drawing<br />
Adjust setting temp.