20x-1280x - Lidl Service Website

More documents

Recommendations

Info

9. Setup MicrOcular Note The MicrOcular only works without the Barlow lens supplied. Magnification setting is changed by using the MicrOcular and must be reset by focussing anew. Remove the Barlow lens (illustration 6. 3) and eyepiece currently in use from the eyepiece holders (illustration 1. 5) and replace them with the MikrOkular (microscope eyepiece) (illustration 5. 4a) and reducer lens (illustration 5. 4b) as in illustration 5 in the holders (illustration 5.5) Please do not yet connect MikrOkular and PC. Please go through the items below in sequence. 10. Installation and use of the software 10.1 Installation of the image processing software Photomizer SE 1 Insert the CD-ROM supplied in your CD or DVD drive. The installation menu opens automatically. If it doesn't, please switch to Windows Explorer and select your CD drive. Start the file “setup.exe“ by double-clicking it. 2. A choice of languages is shown. Choose your preference. Confirm it by clicking "OK". At the "Welcome" screen, click "Next">“. 4. In the next screen you will be asked for the "Destination Folder". Confirm your input with "Next>". 5. The setup status screen shows. This advises current operation status with a progress bar. This may take a few minutes. 6. The "Completed the Photomizer Setup Wizard" screen shows. Click here on "Finish". Note To use the MikrOkular long-term we recommend it always be connected to the same USB port. 10.2 MikrOkular driver installation During Photomizer SE software installation the correct driver for your operating system will be installed automatically. No manual input is needed. In rare cases the device may not be recognised by your computer. As a rule you need then only install the driver manually from the CD. If this fails please refer to the troubleshooting chapter that follows. 10.3 Troubleshooting: the device isn't recognised by the computer (USB) 1. This occurs in rare cases whith some OEM Windows Vista or XP versions. The device is not defective. Updating the notebook or PC USB driver usually suffices. 2. If not, proceed as below. (The maker cannot accept any liability whatsoever in these cases 1 ). Delete ghost devices. These are devices not actually currently connected to your computer. The reason for this is that Windows generates a system settings entry for each USB device ( e.g USB Stick) on each port. It then seeks that/those device/s each time it's started. This slows down USB device recognition and Windows booting and causes non-recognition of USB ports. Cleaning up the system environment and deleting devices that are no longer in use helps here. To do so right click WORKPLACE (COMPU- TER in Vista) and open the PROPERTIES menu. Then click the ADVANCED tab (ADVANCED SYSTEM SETTINGS in Vista) and then ENVIRONMENT VARIABLES. Choose the NEW option in ENVIRON- MENT VARIABLES. Enter the following under VARIABLE NAME. devmgr_show_nonpresent_devices Under VARIABLE VALUE enter "1". Confirm your input with OK and then reboot the computer. Change to the device manager. In the VIEW menu activate the SHOW DEVICES OPTION. The ghost devices previously not shown will now be displayed in light grey. Check the various categories including USB, memory size, etc. Only delete entries for devices you no longer use. 1 1 Source: Microsoft Knowledge Base http://support.microsoft.com/kb/315539/en System requirements: Intel X86 processor with at least 2.0 GHz speed, 200 MB hard disc space, 512 MB RAM memory, Windows XP, Vista (32-bit) or Windows 7 and a free USB port (not via a hub if possible). - 6 - 11 Using the MicrOcular 11.1 Preparation 1. Slide a specimen under your microscope and focus on it. 2. Remove the eyepiece and Barlow lens from the eyepiece support and the dust cap from your MikrOkular and install same in the eyepiece supports instead of the Barlow lens. 3. Start your PC if you haven't yet and connect your MikrOkular to the USB port of your computer. 11.2 Showing and saving MikrOkular images on your PC. 1. Start the Photomizer SE Software. 2. Click "Open camera" 3. If you have more than one device connected up select the one you want from the choice offered. Click "SoC PC-Camera" or "MikrOkular". Omit this step if you only have a single device connected up. 4. The camera image should now be visible on your screen. Focus the microscope image. 5. Click "Capture" to record an image. It will then be shown on the right. 6. Click on it to select it and then click "Transfer image". 7. This takes you to the Photomizer SE software. 8. File - Save as Tip Enlargement can be doubled by omitting the reducer lens (illustration 5.4b). Pull the MikrOkular (Ill. 5.4a) out of the reducer lens (ill. 5.4b) and remove it to do so. Then reinsert the MikrOkular in the eyepiece holders. You may need to re-focus using the focussing device (ill. 1.9). 11.3 The Photomizer SE software If you need help in the "Photomizer SE" programme click "?" and then "Open help". If you need further assistance please visit the maker's home page at www.photomizer.net
12. Care and maintenance: The microscope is a high quality optical appliance. Therefore you should make sure that dust or moisture do not come into contact with your microscope. Avoid putting fingerprints on any optical surfaces. If dust or dirt should nevertheless have gotten onto your microscope, or the accessories, you should first remove this with a soft brush. Then clean the soiled area with a soft, lint-free cloth. To remove fingerprints from the optical surfaces it is best to use a lint-free, soft cloth, to which you have applied some alcohol. After usage, you should stow the microscope and the accessories in their correct containers again. Remember: A well maintained microscope will keep its optical quality for years and thus maintain its value. 13. Troubleshooting: Error Solution No picture visible switch light on / put condenser lens in place / adjust focus Picture flickers while viewing if necessary, adjust solution of the with PC eyepiece video graphics board Software installation reports confirm by clicking “OK” “not XP approved” 14. Specifications System requirements for PC eyepiece Intel Pentium with 166 MHz or equiv. / higher, Operating System Windows ME / 2000 / XP / Vista / 7, Min. 64 MB RAM, Min. 100 MB free hard disk space Magnification table Eyepiece Objective Magnification (with Barlow lens) 5x 4x 20x 40x 5x 10x 50x 100x 5x 40x 200x 400x 16x 4x 64x 128x 16x 10x 160x 320x 16x 40x 640x 1280x LEDs: 2 pcs., type CH-HB3CO4ALD-W LED class 1 · P=64 mW · λ1=432 nm · λ2=514 nm EN 60825-1:1994 + A1:2002 + A2:2001 15. EEC conformity explanation Meade Instruments Europe GmbH & Co KG, resident in 46414 Rhede/Westf., Gutenbergstr. 2, Germany, explains the agreement with in the following specified EEC guidelines for this product: EN 61558-2-6:1997 EN 61558-1:1997 +A1 Product description: Transmission-type microscope Model: BIOLUX NV 20x-1280x Rhede, 01/04/2007 Meade Instruments Europe Helmut Ebbert Managing director - 7 - 16. SERVICE AND GUARANTEE This device is guaranteed for 5 years from the date of purchase. Please keep the receipt as proof of purchase. Our products are manufactured using the latest manufacturing techniques and undergo rigorous quality control. Service Centre Please contact the service centre for any questions regarding the product or claims. Our trained staff will be happy to help. The service hotline is listed below. If it is necessary to make a guarantee claim (repair or exchange), our service staff will supply you with the return address. Service hotline: 00800 6343 7000 Correction of defects and returns We will repair any material or manufacturing defects free of charge during the guarantee period. Excluded from the guarantee are faults due to damage caused by the user, or improper use due to non-authorised third-party attempted repairs or similar. If it is necessary to repair or exchange a product, our service centre employees will supply you with the return address. In the case of returns, please note the following: • Make sure that the article is carefully packaged. If possible use the original packaging. • Fill in the returns form and include it with a copy of your receipt and the product you are returning. Returns form Transaction no.*: .................................................................................. Product name: .................................................................................... Short description of defect: ................................................................ Surname, first name: .......................................................................... Postcode / Town: ................................................................................ Street / House no.: .............................................................................. Telephone: ............................................................................................ Date of purchase: ................................................................................ Signature: ............................................................................................ *will be supplied to you by the service centre GB IE NL BE HU PL SI DE AT CH BE
Page 1 and 2: 20x-1280x GB/IE NL/BE HU PL SI DE/A
Page 3 and 4: E H D X Fig. 1 I 1& 1) B/C 1@ Fig.
Page 5: we make it by means of a pre-treatm
Page 9 and 10: 7. Te observeren object - Aard en p
Page 11 and 12: 12. Verzorging en onderhoud: De mic
Page 13 and 14: 7. Megfigyelési tárgy - Állag é
Page 15 and 16: 12. Ápolás és karbantartás: Az
Page 17 and 18: 7. Obiekt obserwacji - Rodzaj obiek
Page 19 and 20: 12. Środki ostrożności związane
Page 21 and 22: 7. Objekt opazovanja - sestava in p
Page 23 and 24: 11.3 Programska oprema Photomizer S
Page 25 and 26: Beachten Sie: Bei veränderter Verg
Page 27 and 28: ten, zu erfassen. Dies wird dann re
Page 29 and 30: - 29 -

20x-1280x - Lidl Service Website

Create successful ePaper yourself

Delete template?

Save as template?