RAP 80.02 E - Festool

More documents

Recommendations

Info

6.1 Rough speeds for work with different materials a) Polishing Work Setting Distribute polish 1-2 Polishing sensitive surfaces (e.g. painted plastic parts) 3-4 High-gloss polishing 5-6 b) Sanding Work Setting Light sanding of thin topcoats 4-6 Sanding “smearing” paints / varnishes 4-6 Sanding off dry, cracked paint 6 Removing anti-fouling paint 6 Sanding out rust on varnished metal parts (6) Sanding thermoplastics 2-4 Sanding wood 6 Smoothing stained wood with sanding brush 2-4 Cleaning sandstone, concrete, shuttering material 4-6 ( ) Only conditionally suitable 7 AH-RAS 115 extractor hood 7.1 Fitting (Fig. 2) Before fitting the hood, take care to ensure that the clamping lever is in the “released” position (2.2). Press the extractor hood firmly onto the clamping neck of the rotary polisher and fasten by pushing the clamping lever forwards (2.1). Do not start work if the hood extractor hood is not safely and firmly locked onto the clamping neck. If the clamping force should deteriorate after frequent use, adjust the clamping lever: • loosen screw (4.1) on clamping lever and remove clamping lever (4.2), • tighten square-head threaded bolt (4.3) by hand, • replace clamping lever and fasten with screw. The optimum position can be determined by closing the clamping lever before tightening the screw. 7.2 Changing the position of the rotating handle The rotating additional handle can be also be fastened on the right of the extractor hood depending on the user’s personal preferences. It should be exchanged with the clamping lever. • Loosen screw (4.1) on clamping lever and remove clamping lever (4.2). • Remove square-head threaded bolt (4.3). • Loosen additional handle (5.2) with Allen key, size 6. The clamping lever and additional handle can 8 now be exchanged. Reassemble in reverse order. You can adjust the free-running of the rotating additional handle using the counternut (5.1) by clamping this against the hood with an openend spanner, size 13, before tightening the additional handle. 7.3 Changing the brush insert Press the brush insert out by inserting a screwdriver into the square hole (5.5). Place the new brush insert into the groove, adjust the radius by bending slightly and push in firmly until the insert rests on the base of the hood. The bevel of the bristles must hereby point outwards. Two different brush inserts are available: • AH-RAS D 115 Poly (Order No. 484 727), contains 2 polyamide brushes (as replacements for worn brushes). • AH-RAS D 115 Metal (Order No. 484 728), contains 1 metal brush (for use on materials which produce sparks). 7.4 Changing the sanding pad In normal cases the sanding pad (1.2) can be unscrewed from the working spindle by hand after the spindle stop (1.3) has been pressed. However, should the sanding pad sit firmly • Remove brush insert • Insert special key (5.3) through slot (5.4) into the tool’s key slot. • Press the spindle stop and loosen the tool by turning the special key. Always screw the sanding pad onto the working spindle by hand. This greatly facilitates a later loosening. 7.5 Sanding and dust extraction Connect the hose (Ø 27 mm) of a Festool dust extractor to the adapter (3.2) on the rear of the rotary polisher’s casing. The brush (3.3) can be adjusted with the rotating handle (3.4). This permits an optimum adjustment to the respective working position. Always rotate the brush in the direction of flight of the sanding dust. When sanding metals and other materials which produce sparks, a spark trap (Order No. 484 733) must be fitted between the dust extractor and rotary polisher for safety reasons.
8 Fitting tools Do not use tools whose maximum permissible speed is lower than the speed specified on the rotary polisher’s ratings plate. This is guaranteed with all original accessories from Festool. There are two types of fixtures depending on the tools used. The motor spindle is locked by pressing the spindle stop (1.3). This permits a fast and easy replacement of the tools used. 8.1 Direct fitting The sanding pad STF D80 included with the tool and the polishing drum available as an accessory, together with the individual sanding disks, all have an M14 thread. These can be screwed directly into the working spindle. 8.2 Fitting with locking nut The flexible sanding pad is fastened to the drive shaft with a locking nut and tightened with the face spanner. 9 Additional handle The additional handle (1.4) can be optionally fitted on the right or left of the rotary polisher’s transmission head. 10 PoliStick and Stickfix System All PoliStick felts are mounted on the STF D80 polishing pad. Stickfix sanding discs D115 are fastened on the Stickfix sanding pad STF D115. Only use polishing and sanding pads with undamaged Stickfix adhesive covering. Check before use whether the hook-eye fastening has been damaged by incorrect use (e.g. melted). 11 Accessories The accessory order number can be found in your Festool catalogue or on the Internet under ”www.festool.com". 9 12 Care and maintenance Always disconnect the machine at its mains plug before performing maintenance work! Keep the ventilation slots in the motor housing clean and free of obstructions at all times to ensure an adequate circulation of air. The tool is fitted with special motor brushes with an automatic cut-out. When the brushes become worn the power supply is shut off automatically and the polisher comes to a standstill. Any maintenance and repair work requiring an opening of the motor housing may only be carried out by an authorised customer service workshop. 13 Warranty Our equipment is under warranty for at least 12 months with regard to material or production faults in accordance with national legislation. In the EU countries, the warranty period is 24 months (an invoice or delivery note is required as proof of purchase). Damage resulting from, in particular, normal wear and tear, overloading, improper handling, or caused by the user or other damage caused by not following the operating instructions, or any fault acknowledged at the time of purchase, is not covered by the warranty. Complaints will only be acknowledged if the equipment has not been dismantled before being sent back to the suppliers or to an authorised Festool customer support workshop. Store the operating instructions, safety notes, spare parts list and proof of purchase in a safe place. In addition, the manufacturer’s current warranty conditions apply. Note We reserve the right to make changes to the technical data contained in this information as a result of ongoing research and development work.
Page 1 and 2: 463 304_001 RAP 80.02 E Bedienungsa
Page 4 and 5: 1 Technische Daten RAP 80.02 E Leis
Page 6 and 7: Drehen Sie den Bürstenkranz immer
Page 10 and 11: 1 Caractéristiques techniques RAP
Page 12 and 13: 7.5 Ponçage et aspiration Pour l
Page 14 and 15: 6 Trabajando con la pulidora RAP 80
Page 16 and 17: 1 Dati tecnici RAP 80.02 E Assorbim
Page 18 and 19: La spazzola (3.3) si può regolare
Page 20 and 21: Een gebrekkige electronica herkent
Page 22 and 23: 1 Teknisk data RAP 80.02 E Effektup
Page 24 and 25: När man sliper metall och andra gn
Page 26 and 27: 6 Työskentely kiillotuskoneella RA
Page 28 and 29: 1 Tekniske data RAP 80.02 E Optagen
Page 30 and 31: 8 Montering af indsatsværktøj Bru
Page 32 and 33: 6 Arbeide med RAP 80.02 E Maskinen
Page 34 and 35: 1 Dados técnicos RAP 80.02 E Potê
Page 36 and 37: Dessa forma, proporciona-se o melho
Page 38 and 39: 6 Ðàáîòà ñ RAP 80.02 E Ìà
Page 40 and 41: 1 Technické údaje RAP 80.02 E Pø
Page 42 and 43: 10 Systémy PoliStick a Stickfix V
Page 44 and 45: 6.1 Wartoœci wytyczne prêdkoœci
Page 46 and 47: 1 Mûszaki adatok RAP 80.02 E Telje
Page 48 and 49: 8 A betétszerszámok beszerelése
Page 50 and 51: 6 Åñãáóßåò ìå RAP 80.02
Page 54: Festool GmbH Postfach 1163 D- 73236

RAP 80.02 E - Festool

Create successful ePaper yourself

Delete template?

Save as template?