GUIDE TCI LED DRIVERS 2016-17
MP 65 H Direct current electronic drivers with DIP-SWITCH Alimentatori elettronici in corrente continua con DIP-SWITCH Made in Europe professional led applications (3) 05 SELV 2.1 RIPPLE FREE Multipower LED drivers Alimentatori LED multipotenza Rated Voltage Tensione Nominale 110 ÷ 127 V (2) 220 ÷ 240 V Frequency Frequenza 50...60 Hz AC Operation range Tensione di utilizzo AC 99 ÷ 264 V DC Operation range Tensione di utilizzo DC 176 ÷ 280 V Power Potenza 0 ÷ 65 W Maximum current output ripple Max. ondulazione della corrente uscita ≤ 3% (1) Reference Norms Norme di riferimento: CSA C22.2 NO. 250.13-14 EN 50172 (VDE 0108) EN 55015 EN 61000-3-2 EN 61000-3-3 EN 61347-1 EN 61347-2-13 EN 61547 EN 62384 UL 8750 Article Articolo MP 65 H/2 (MP 60 H/2) MP 65 HBI (MP 60 HBI) MP 65 H/2 Code Codice 127071 (ex 127070) 127051 (ex 127050) P out W V out DC I out DC n° LED max. (1) V out max. ta °C tc °C l max. Power Factor h max. Efficiency (1) 25 (25 (2) ) 10...70 350 mA cost. 20 95 -25...+50 80 0,98 >90 31 (31 (2) ) 10...70 450 mA cost. 20 35 (35 (2) ) 2...70 500 mA cost. 20 38 (38 (2) ) 2...69 550 mA cost. 20 41 (40 (2) ) 2...68 600 mA cost. 18...20 48 (40 (2) ) 2...68 700 mA cost. 18 52 (40 (2) ) 2...66 800 mA cost. 16...18 60 (40 (2) ) 2...66 900 mA cost. 16 63 (40 (2) ) 2...66 950 mA cost. 16 65 (40 (2) ) 2...62 1,05 A cost. 14 65 (40 (2) ) 2...54 1,2 A cost. 14 58Vout voltage limit settable with Dip-Switch - Poutmax=65W (1) Referred to V in = 230 V, 100% load - Riferito a V in = 230 V, carico 100% Features • Multipower driver supplied with dip-switch for the selection of the output current. • IP20 independent driver, for indoor use (MP 65 H/2). • Class I protection against electric shock for direct or indirect contact (MP 65 H/2). • Driver for built-in use (MP 65 HBI). • It can be used for lighting equipment in protection class I (MP 65 HBI). • Active Power Factor Corrector. • Auxiliary output 12 V max. 100 mA. • Current regulation ±5 % including temperature variations. • Input and output terminal blocks on the same side (wire cross-section up to 1,5 - 2,5 mm 2 / AWG15 - AWG13). • Clamping screws on primary and secondary circuits for cables with diameter: min. 3 mm - max. 8 mm (MP 65 H/2). • Driver can be secured with slot for screws. • Protections: - against overheating and short circuits; - against mains voltage spikes; - against overloads. • Thermal protection = C.5.a. MP 65 HBI Accessories not supplied - Accessori non a corredo Article - Articolo L (length) Code - Codice 6-pin cable for LED and AUX Cavo 6 poli per LED e AUX 50 cm / 19,68'' 425720017 Caratteristiche • Alimentatore multipotenza fornito di dip-switch per la selezione della corrente in uscita. • Alimentatore indipendente IP20, per uso interno (MP 65 H/2). • Protetto in classe I contro le scosse elettriche per contatti diretti e indiretti (MP 65 H/2). • Alimentatore da incorporare (MP 65 HBI). • Utilizzabile per apparecchi di illuminazione in classe di protezione I (MP 65 HBI). • PFC attivo. • Uscita ausiliare 12 V max. 100 mA. • Corrente regolata ±5 % incluse variazioni di temperatura. • Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino a 1,5 - 2,5 mm 2 / AWG15 - AWG13). • Serracavo su primario e secondario per cavi di diametro: min. 3 mm - max. 8 mm (MP 65 H/2). • Fissaggio dell’alimentatore tramite asole per viti. • Protezioni: - termica e cortocircuito; - contro le extra-tensioni di rete; - contro i sovraccarichi. • Protezione termica = C.5.a. 64 www.tci.it TCI professional LED applications
MP 65 H Direct current electronic drivers with DIP-SWITCH Alimentatori elettronici in corrente continua con DIP-SWITCH Made in Europe professional led applications Ø90 3,54’’ Weight - Peso gr. 250 / 9 oz. Pcs - Pezzi 40 Compatible with ZHAGA (AM2) Weight - Peso gr. 235 / 9 oz. Pcs - Pezzi 40 30 1,18’’ 30 118’’ 129 5,08’’ 110 4,33’’ 2.1 76 2,99’’ 63,5 2,50’’ 76 2,99’’ 115,5 4,55’’ 99 3,90’’ Wiring diagram - Schema di collegamento (Max. LED distance on page info8 - Massima distanza LED a pagina info8) 64 2,52’’ Multipower LED drivers Alimentatori LED multipotenza DIP-SWITCH 6 5 4 3 2 1 _ SEC SEC + 12Vaux + SEC _ LED SIGNAL GND PRI N L Vin TCI professional LED applications www.tci.it 65
- Page 48 and 49: 1. MWU Direct current electronic dr
- Page 50 and 51: W HPF professional led applications
- Page 52 and 53: KU2 professional led applications 1
- Page 54 and 55: DC MICRO Z professional led applica
- Page 56 and 57: Multipower LED drivers Alimentatori
- Page 58 and 59: UNIVERSALE 20 Direct current electr
- Page 60 and 61: UNIVERSALE 20 LC Direct current ele
- Page 62 and 63: UNIVERSALE 20 HC Direct current ele
- Page 64 and 65: UNIVERSALE 20 WR Direct current ele
- Page 66 and 67: MP 32 K2 Direct current electronic
- Page 68 and 69: MP 32 HV K2 Direct current electron
- Page 70 and 71: MP 39 K2 Direct current electronic
- Page 72 and 73: WIDESQUARE 30/350-700 Direct curren
- Page 74 and 75: SMARTx 26 PLUS Direct current elect
- Page 76 and 77: SMART 32 Direct current electronic
- Page 78 and 79: SMART 42 Direct current electronic
- Page 80 and 81: PROFESSIONALE 34 Direct current ele
- Page 82 and 83: PROFESSIONALE 42 Direct current ele
- Page 84 and 85: SMART 50 Direct current electronic
- Page 86 and 87: MP 50 K3 Direct current electronic
- Page 88 and 89: MP 50 SV K3 - SELV 60 V Direct curr
- Page 90 and 91: MP 50 TCM Direct current electronic
- Page 92 and 93: MP 54 BI Direct current electronic
- Page 94 and 95: MP 55 HC Direct current electronic
- Page 96 and 97: MP 55 / 120 HC Direct current elect
- Page 100 and 101: MP 65 HTCM Direct current electroni
- Page 102 and 103: SMART 70 Direct current electronic
- Page 104 and 105: SUPERSLIM Direct current electronic
- Page 106 and 107: ATON 30/250-700 Direct current elec
- Page 108 and 109: ATON 30/700-1400 Direct current ele
- Page 110 and 111: MP 32 SLIM Direct current electroni
- Page 112 and 113: MP 60 SLIM Direct current electroni
- Page 114 and 115: SMART 70 HC SLIM Direct current ele
- Page 116 and 117: MP 50/350 SLIM Direct current elect
- Page 118 and 119: MP 80/500 SLIM Direct current elect
- Page 120 and 121: MP 80/500 SLIM LS - LEDset2 Direct
- Page 122 and 123: professional led applications Made
- Page 124 and 125: MICRO JOLLY 6 - 1...10 V & PUSH Dir
- Page 126 and 127: MOONLIGHT 6 Direct current dimmable
- Page 128 and 129: RD57 - 1...10 V & PUSH Direct curre
- Page 130 and 131: MICRO MD professional led applicati
- Page 132 and 133: MINIJOLLY 20 - 1...10 V & PUSH Dire
- Page 134 and 135: MINIJOLLY DALI 20 professional led
- Page 136 and 137: MINIJOLLY LC 20 - 1...10 V & PUSH D
- Page 138 and 139: MINIJOLLY LC DALI 20 Direct current
- Page 140 and 141: MINIJOLLY HV Direct current dimmabl
- Page 142 and 143: MINIJOLED - 1...10 V & PUSH Direct
- Page 144 and 145: MINI MD Direct current dimmable (TR
- Page 146 and 147: JOLLY 25 - 1...10 V & PUSH Direct c
MP 65 H<br />
Direct current electronic drivers with DIP-SWITCH<br />
Alimentatori elettronici in corrente continua con DIP-SWITCH<br />
Made in Europe<br />
professional led applications<br />
(3)<br />
05<br />
SELV<br />
2.1<br />
RIPPLE<br />
FREE<br />
Multipower <strong>LED</strong> drivers<br />
Alimentatori <strong>LED</strong> multipotenza<br />
Rated Voltage<br />
Tensione Nominale<br />
110 ÷ 127 V (2)<br />
220 ÷ 240 V<br />
Frequency<br />
Frequenza<br />
50...60 Hz<br />
AC Operation range<br />
Tensione di utilizzo AC<br />
99 ÷ 264 V<br />
DC Operation range<br />
Tensione di utilizzo DC<br />
<strong>17</strong>6 ÷ 280 V<br />
Power<br />
Potenza<br />
0 ÷ 65 W<br />
Maximum current<br />
output ripple<br />
Max. ondulazione<br />
della corrente uscita<br />
≤ 3% (1)<br />
Reference Norms<br />
Norme di riferimento:<br />
CSA C22.2 NO. 250.13-14<br />
EN 50<strong>17</strong>2 (VDE 0108)<br />
EN 55015<br />
EN 61000-3-2<br />
EN 61000-3-3<br />
EN 61347-1<br />
EN 61347-2-13<br />
EN 61547<br />
EN 62384<br />
UL 8750<br />
Article<br />
Articolo<br />
MP 65 H/2<br />
(MP 60 H/2)<br />
MP 65 HBI<br />
(MP 60 HBI)<br />
MP 65 H/2<br />
Code<br />
Codice<br />
127071<br />
(ex 127070)<br />
127051<br />
(ex 127050)<br />
P out<br />
W<br />
V out<br />
DC<br />
I out<br />
DC<br />
n° <strong>LED</strong><br />
max. (1)<br />
V out<br />
max.<br />
ta<br />
°C<br />
tc<br />
°C l max.<br />
Power<br />
Factor<br />
h max.<br />
Efficiency (1)<br />
25 (25 (2) ) 10...70 350 mA cost. 20 95 -25...+50 80 0,98 >90<br />
31 (31 (2) ) 10...70 450 mA cost. 20<br />
35 (35 (2) ) 2...70 500 mA cost. 20<br />
38 (38 (2) ) 2...69 550 mA cost. 20<br />
41 (40 (2) ) 2...68 600 mA cost. 18...20<br />
48 (40 (2) ) 2...68 700 mA cost. 18<br />
52 (40 (2) ) 2...66 800 mA cost. 16...18<br />
60 (40 (2) ) 2...66 900 mA cost. 16<br />
63 (40 (2) ) 2...66 950 mA cost. 16<br />
65 (40 (2) ) 2...62 1,05 A cost. 14<br />
65 (40 (2) ) 2...54 1,2 A cost. 14<br />
58Vout voltage limit settable with Dip-Switch - Poutmax=65W<br />
(1)<br />
Referred to V in<br />
= 230 V, 100% load - Riferito a V in<br />
= 230 V, carico 100%<br />
Features<br />
• Multipower driver supplied with dip-switch for the selection of<br />
the output current.<br />
• IP20 independent driver, for indoor use (MP 65 H/2).<br />
• Class I protection against electric shock for direct or indirect<br />
contact (MP 65 H/2).<br />
• Driver for built-in use (MP 65 HBI).<br />
• It can be used for lighting equipment in protection class I<br />
(MP 65 HBI).<br />
• Active Power Factor Corrector.<br />
• Auxiliary output 12 V max. 100 mA.<br />
• Current regulation ±5 % including temperature variations.<br />
• Input and output terminal blocks on the same side (wire<br />
cross-section up to 1,5 - 2,5 mm 2 / AWG15 - AWG13).<br />
• Clamping screws on primary and secondary circuits for cables<br />
with diameter: min. 3 mm - max. 8 mm (MP 65 H/2).<br />
• Driver can be secured with slot for screws.<br />
• Protections:<br />
- against overheating and short circuits;<br />
- against mains voltage spikes;<br />
- against overloads.<br />
• Thermal protection = C.5.a.<br />
MP 65 HBI<br />
Accessories not supplied - Accessori non a corredo<br />
Article - Articolo L (length) Code - Codice<br />
6-pin cable for <strong>LED</strong> and AUX<br />
Cavo 6 poli per <strong>LED</strong> e AUX<br />
50 cm / 19,68'' 4257200<strong>17</strong><br />
Caratteristiche<br />
• Alimentatore multipotenza fornito di dip-switch per la selezione<br />
della corrente in uscita.<br />
• Alimentatore indipendente IP20, per uso interno (MP 65 H/2).<br />
• Protetto in classe I contro le scosse elettriche per contatti<br />
diretti e indiretti (MP 65 H/2).<br />
• Alimentatore da incorporare (MP 65 HBI).<br />
• Utilizzabile per apparecchi di illuminazione in classe di<br />
protezione I (MP 65 HBI).<br />
• PFC attivo.<br />
• Uscita ausiliare 12 V max. 100 mA.<br />
• Corrente regolata ±5 % incluse variazioni di temperatura.<br />
• Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino a<br />
1,5 - 2,5 mm 2 / AWG15 - AWG13).<br />
• Serracavo su primario e secondario per cavi di diametro:<br />
min. 3 mm - max. 8 mm (MP 65 H/2).<br />
• Fissaggio dell’alimentatore tramite asole per viti.<br />
• Protezioni:<br />
- termica e cortocircuito;<br />
- contro le extra-tensioni di rete;<br />
- contro i sovraccarichi.<br />
• Protezione termica = C.5.a.<br />
64 www.tci.it<br />
<strong>TCI</strong> professional <strong>LED</strong> applications