GUIDE TCI LED DRIVERS 2016-17
SMART 50 Direct current electronic drivers with DIP-SWITCH Alimentatori elettronici in corrente continua con DIP-SWITCH Made in Europe professional led applications 05 (2) SELV 2.1 Multipower LED drivers Alimentatori LED multipotenza Rated Voltage Tensione Nominale 220 ÷ 240 V Frequency Frequenza 50...60 Hz AC Operation range Tensione di utilizzo AC 198 ÷ 264 V DC Operation range Tensione di utilizzo DC 170 ÷ 280 V Power Potenza 3,5 ÷ 50 W Typical ripple at max output current Ondulazione tipica alla massima corrente uscita ± 20 % (1) Reference Norms Norme di riferimento: EN 50172 (VDE 0108) EN 55015 EN 61000-3-2 EN 61347-1 EN 61347-2-13 EN 61547 Article Articolo SMART 50 Code Codice P out W V out DC I out DC n° LED max. (1) V out max. ta °C tc °C l max. Power Factor h max. Efficiency (1) SMART 50 (2) 122220 27 10...78 350 mA cost. 25 90 -25...+50 90 0,95 > 90 SMART 50 BI 122219 31 10...78 400 mA cost. 25 35 10...78 450 mA cost. 24 39 10...78 500 mA cost. 22 43 10...78 550 mA cost. 22 47 10...78 600 mA cost. 20 50 10...77 650 mA cost. 20 50 10...71 700 mA cost. 18 50 10...66 750 mA cost. 17 -25...+45 50 10...62 800 mA cost. 16 50 10...59 850 mA cost. 15 50 10...55 900 mA cost. 14 50 10...53 950 mA cost. 13 50 10...50 1000 mA cost. 12 50 10...48 1050 mA cost. 12 (1) Referred to V in = 230 V, 100% load - Riferito a V in = 230 V, carico 100% Features • Multipower driver supplied with dip-switch for the selection of the output current. • IP20 independent driver, for indoor use (SMART 50). • Class I protection against electric shock for direct or indirect contact (SMART 50). • Driver for built-in use (SMART 50 BI). • Active Power Factor Corrector. • It can be used for lighting equipment in protection class I. • Analogical input (NTC) for thermal sensor connection. • Current regulation ±5 % including temperature variations. • Input and output terminal blocks on the same side (wire cross-section up to 1,5 mm 2 / AWG15). • Clamping screws on primary and secondary circuits for cables with diameter: min. 2 mm - max. 9 mm (SMART 50). • Driver can be secured with slot for screws. • Protections: - against overheating and short circuits; - against mains voltage spikes; - against overloads. • Thermal protection = C.5.a. SMART 50 BI Caratteristiche • Alimentatore multipotenza fornito di dip-switch per la selezione della corrente in uscita. • Alimentatore indipendente IP20, per uso interno (SMART 50). • Protetto in classe I contro le scosse elettriche per contatti diretti e indiretti (SMART 50). • Alimentatore da incorporare (SMART 50 BI). • PFC attivo. • Utilizzabile per apparecchi di illuminazione in classe di protezione I. • Entrata analogica (NTC) per connessione sensore termico. • Corrente regolata ±5 % incluse variazioni di temperatura. • Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino a 1,5 mm 2 / AWG15). • Serracavo su primario e secondario per cavi di diametro: min. 2 mm - max. 9 mm (SMART 50). • Fissaggio dell’alimentatore tramite asole per viti. • Protezioni: - termica e cortocircuito; - contro le extra-tensioni di rete; - contro i sovraccarichi. • Protezione termica = C.5.a. 50 www.tci.it TCI professional LED applications
SMART 50 Direct current electronic drivers with DIP-SWITCH Alimentatori elettronici in corrente continua con DIP-SWITCH Made in Europe professional led applications Ø90 3,54’’ Weight - Peso gr. 250 / 9 oz. Pcs - Pezzi 40 Compatible with ZHAGA (AM2) Weight - Peso gr. 235 / 9 oz. Pcs - Pezzi 40 30 1,18’’ 30 118’’ 129 5,08’’ 110 4,33’’ 2.1 76 2,99’’ 63,5 2,50’’ 76 2,99’’ 115,5 4,55’’ 99 3,90’’ Wiring diagram - Schema di collegamento (Max. LED distance on page info8 - Massima distanza LED a pagina info8) 64 2,52’’ Multipower LED drivers Alimentatori LED multipotenza DIP-SWITCH 4 3 2 1 SEC + _ LED NTC + _ THERMAL SENSOR PRI N L Vin TCI professional LED applications www.tci.it 51
- Page 34 and 35: LED choice table Tabella di scelta
- Page 36 and 37: professional led applications Made
- Page 38 and 39: BULL/U professional led application
- Page 40 and 41: STC HC professional led application
- Page 42 and 43: 1. STF/U Direct current electronic
- Page 44 and 45: DCC/U S professional led applicatio
- Page 46 and 47: DC AR professional led applications
- Page 48 and 49: 1. MWU Direct current electronic dr
- Page 50 and 51: W HPF professional led applications
- Page 52 and 53: KU2 professional led applications 1
- Page 54 and 55: DC MICRO Z professional led applica
- Page 56 and 57: Multipower LED drivers Alimentatori
- Page 58 and 59: UNIVERSALE 20 Direct current electr
- Page 60 and 61: UNIVERSALE 20 LC Direct current ele
- Page 62 and 63: UNIVERSALE 20 HC Direct current ele
- Page 64 and 65: UNIVERSALE 20 WR Direct current ele
- Page 66 and 67: MP 32 K2 Direct current electronic
- Page 68 and 69: MP 32 HV K2 Direct current electron
- Page 70 and 71: MP 39 K2 Direct current electronic
- Page 72 and 73: WIDESQUARE 30/350-700 Direct curren
- Page 74 and 75: SMARTx 26 PLUS Direct current elect
- Page 76 and 77: SMART 32 Direct current electronic
- Page 78 and 79: SMART 42 Direct current electronic
- Page 80 and 81: PROFESSIONALE 34 Direct current ele
- Page 82 and 83: PROFESSIONALE 42 Direct current ele
- Page 86 and 87: MP 50 K3 Direct current electronic
- Page 88 and 89: MP 50 SV K3 - SELV 60 V Direct curr
- Page 90 and 91: MP 50 TCM Direct current electronic
- Page 92 and 93: MP 54 BI Direct current electronic
- Page 94 and 95: MP 55 HC Direct current electronic
- Page 96 and 97: MP 55 / 120 HC Direct current elect
- Page 98 and 99: MP 65 H Direct current electronic d
- Page 100 and 101: MP 65 HTCM Direct current electroni
- Page 102 and 103: SMART 70 Direct current electronic
- Page 104 and 105: SUPERSLIM Direct current electronic
- Page 106 and 107: ATON 30/250-700 Direct current elec
- Page 108 and 109: ATON 30/700-1400 Direct current ele
- Page 110 and 111: MP 32 SLIM Direct current electroni
- Page 112 and 113: MP 60 SLIM Direct current electroni
- Page 114 and 115: SMART 70 HC SLIM Direct current ele
- Page 116 and 117: MP 50/350 SLIM Direct current elect
- Page 118 and 119: MP 80/500 SLIM Direct current elect
- Page 120 and 121: MP 80/500 SLIM LS - LEDset2 Direct
- Page 122 and 123: professional led applications Made
- Page 124 and 125: MICRO JOLLY 6 - 1...10 V & PUSH Dir
- Page 126 and 127: MOONLIGHT 6 Direct current dimmable
- Page 128 and 129: RD57 - 1...10 V & PUSH Direct curre
- Page 130 and 131: MICRO MD professional led applicati
- Page 132 and 133: MINIJOLLY 20 - 1...10 V & PUSH Dire
SMART 50<br />
Direct current electronic drivers with DIP-SWITCH<br />
Alimentatori elettronici in corrente continua con DIP-SWITCH<br />
Made in Europe<br />
professional led applications<br />
Ø90<br />
3,54’’<br />
Weight - Peso gr. 250 / 9 oz.<br />
Pcs - Pezzi 40<br />
Compatible with ZHAGA (AM2)<br />
Weight - Peso gr. 235 / 9 oz.<br />
Pcs - Pezzi 40<br />
30<br />
1,18’’<br />
30<br />
118’’<br />
129<br />
5,08’’<br />
110<br />
4,33’’<br />
2.1<br />
76<br />
2,99’’<br />
63,5<br />
2,50’’<br />
76<br />
2,99’’<br />
115,5<br />
4,55’’ 99<br />
3,90’’<br />
Wiring diagram - Schema di collegamento (Max. <strong>LED</strong> distance on page info8 - Massima distanza <strong>LED</strong> a pagina info8)<br />
64<br />
2,52’’<br />
Multipower <strong>LED</strong> drivers<br />
Alimentatori <strong>LED</strong> multipotenza<br />
DIP-SWITCH<br />
4<br />
3<br />
2<br />
1<br />
SEC<br />
+ _<br />
<strong>LED</strong><br />
NTC<br />
+<br />
_<br />
THERMAL<br />
SENSOR<br />
PRI<br />
N<br />
L<br />
Vin<br />
<strong>TCI</strong> professional <strong>LED</strong> applications www.tci.it<br />
51