GUIDE TCI LED DRIVERS 2016-17
UNIVERSALE 20 WR Direct current electronic drivers with DIP-SWITCH Alimentatori elettronici in corrente continua con DIP-SWITCH Made in Europe professional led applications SELV 2.1 RIPPLE FREE Multipower LED drivers Alimentatori LED multipotenza Rated Voltage Tensione Nominale 110 ÷ 127 V (3) 220 ÷ 277 V Frequency Frequenza 50...60 Hz AC Operation range Tensione di utilizzo AC 198 ÷ 264 V DC Operation range Tensione di utilizzo DC 170 ÷ 280 V Power Potenza 0 ÷ 20 W Maximum current output ripple Max. ondulazione della corrente uscita ≤ 3% (1) Reference Norms Norme di riferimento: EN 50172 (VDE 0108) EN 55015 EN 60335-1 EN 61000-3-2 EN 61000-3-3 EN 61347-1 EN 61347-2-13 EN 61547 EN 62384 VDE 0710-T14 Article Articolo UNIVERSALE 20 WR UNIVERSALE 20 WR BI UNIVERSALE 20 WR Code Codice 127140 127142 P out W V out DC I out DC n° LED max. (1) V out max. ta °C tc °C l max. h max. Power Efficiency (1) Factor Constant current output - Uscita in corrente costante -25...+50 80 (2) 0,97 >88 13 (13 (3) ) 10...54 250 mA cost. 16...18 59 19 (15 (3) ) 2...54 350 mA cost. 16...18 20 (15 (3) ) 2...50 400 mA cost. 15/16 20 (15 (3) ) 2...44 450 mA cost. 12...14 20 (15 (3) ) 2...40 500 mA cost. 11/12 20 (15 (3) ) 2...37 550 mA cost. 10/11 20 (15 (3) ) 2...34 600 mA cost. 9/10 20 (15 (3) ) 2...29 700 mA cost. 8/9 Constant voltage output - Uscita in tensione costante 16 (15 (3) ) 24 cost. 700 mA max. - - (1) Referred to V in = 230 V, 100% load - Riferito a V in = 230 V, carico 100% (2) Tc = 75°C for Pout ≤16W AVAILABLE SOON Features • Multipower driver supplied with dip-switch for the selection of the output current. • IP20 independent driver, for indoor use (UNIVERSALE 20 WR). • Class II protection against electric shock for direct or indirect contact (UNIVERSALE 20 WR). • Driver for built-in use (UNIVERSALE 20 WR BI). • It can be used for lighting equipment in protection class I and II (UNIVERSALE 20 WR BI). • Active Power Factor Corrector. • Current regulation ±5 % including temperature variations. • Supplied with terminal cover and cable retainer. • Input and output terminal blocks on the same side (wire cross-section up to 1,5 mm 2 / AWG15). • Clamping screws on primary and secondary circuits for cables with diameter: min. 3 mm - max. 8 mm (UNIVERSALE 20 WR). • Driver can be secured with slot for screws. • Protections: - against overheating and short circuits; - against mains voltage spikes; - against overloads. • Thermal protection = C.5.a. • Double output impedance for use in household electrical appliances. UNIVERSALE 20 WR BI Caratteristiche • Alimentatore multipotenza fornito di dip-switch per la selezione della corrente in uscita. • Alimentatore indipendente IP20, per uso interno (UNIVERSALE 20 WR). • Protetto in classe II contro le scosse elettriche per contatti diretti e indiretti (UNIVERSALE 20 WR). • Alimentatore da incorporare (UNIVERSALE 20 WR BI). • Utilizzabile per apparecchi di illuminazione in classe di protezione I e II (UNIVERSALE 20 WR BI). • PFC attivo. • Corrente regolata ±5 % incluse variazioni di temperatura. • Fornito di coprimorsetto e serracavo. • Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino a 1,5 mm 2 / AWG15). • Serracavo su primario e secondario per cavi di diametro: min. 3 mm - max. 8 mm (UNIVERSALE 20 WR). • Fissaggio dell’alimentatore tramite asole per viti. • Protezioni: - termica e cortocircuito; - contro le extra-tensioni di rete; - contro i sovraccarichi. • Protezione termica = C.5.a. • Doppia impedenza d’uscita per l’utilizzo in apparecchi elettrodomestici. 30 www.tci.it TCI professional LED applications
UNIVERSALE 20 WR Direct current electronic drivers with DIP-SWITCH Alimentatori elettronici in corrente continua con DIP-SWITCH Made in Europe professional led applications Ø55 2,17’’ Weight - Peso gr. 108 / 3,50 oz. Pcs - Pezzi 50 Weight - Peso gr. 100 / 3,50 oz. Pcs - Pezzi 50 108 4,25’’ 108 4,25’’ 27,5 1,08’’ 52 2,05’’ 52 2,05’’ 2.1 110,4 4,35’’ 22 0,87’’ Wiring diagram - Schema di collegamento (Max. LED distance on page info8 - Massima distanza LED a pagina info8) 100 3,94’’ 92 3,62’’ 22 0,87’’ Multipower LED drivers Alimentatori LED multipotenza SEC + _ LED PRI V in TCI professional LED applications www.tci.it 31
- Page 14 and 15: Summary Sommario professional led a
- Page 16 and 17: Index in order of CODE Indice in or
- Page 18 and 19: Index in order of CODE Indice in or
- Page 20 and 21: Index in order of ARTICLE Indice in
- Page 22 and 23: Index in order of ARTICLE Indice in
- Page 24 and 25: Index in order of ARTICLE Indice in
- Page 26 and 27: Power LED Power LED professional le
- Page 28 and 29: LED choice table Tabella di scelta
- Page 30 and 31: LED choice table Tabella di scelta
- Page 32 and 33: LED choice table Tabella di scelta
- Page 34 and 35: LED choice table Tabella di scelta
- Page 36 and 37: professional led applications Made
- Page 38 and 39: BULL/U professional led application
- Page 40 and 41: STC HC professional led application
- Page 42 and 43: 1. STF/U Direct current electronic
- Page 44 and 45: DCC/U S professional led applicatio
- Page 46 and 47: DC AR professional led applications
- Page 48 and 49: 1. MWU Direct current electronic dr
- Page 50 and 51: W HPF professional led applications
- Page 52 and 53: KU2 professional led applications 1
- Page 54 and 55: DC MICRO Z professional led applica
- Page 56 and 57: Multipower LED drivers Alimentatori
- Page 58 and 59: UNIVERSALE 20 Direct current electr
- Page 60 and 61: UNIVERSALE 20 LC Direct current ele
- Page 62 and 63: UNIVERSALE 20 HC Direct current ele
- Page 66 and 67: MP 32 K2 Direct current electronic
- Page 68 and 69: MP 32 HV K2 Direct current electron
- Page 70 and 71: MP 39 K2 Direct current electronic
- Page 72 and 73: WIDESQUARE 30/350-700 Direct curren
- Page 74 and 75: SMARTx 26 PLUS Direct current elect
- Page 76 and 77: SMART 32 Direct current electronic
- Page 78 and 79: SMART 42 Direct current electronic
- Page 80 and 81: PROFESSIONALE 34 Direct current ele
- Page 82 and 83: PROFESSIONALE 42 Direct current ele
- Page 84 and 85: SMART 50 Direct current electronic
- Page 86 and 87: MP 50 K3 Direct current electronic
- Page 88 and 89: MP 50 SV K3 - SELV 60 V Direct curr
- Page 90 and 91: MP 50 TCM Direct current electronic
- Page 92 and 93: MP 54 BI Direct current electronic
- Page 94 and 95: MP 55 HC Direct current electronic
- Page 96 and 97: MP 55 / 120 HC Direct current elect
- Page 98 and 99: MP 65 H Direct current electronic d
- Page 100 and 101: MP 65 HTCM Direct current electroni
- Page 102 and 103: SMART 70 Direct current electronic
- Page 104 and 105: SUPERSLIM Direct current electronic
- Page 106 and 107: ATON 30/250-700 Direct current elec
- Page 108 and 109: ATON 30/700-1400 Direct current ele
- Page 110 and 111: MP 32 SLIM Direct current electroni
- Page 112 and 113: MP 60 SLIM Direct current electroni
UNIVERSALE 20 WR<br />
Direct current electronic drivers with DIP-SWITCH<br />
Alimentatori elettronici in corrente continua con DIP-SWITCH<br />
Made in Europe<br />
professional led applications<br />
SELV<br />
2.1<br />
RIPPLE<br />
FREE<br />
Multipower <strong>LED</strong> drivers<br />
Alimentatori <strong>LED</strong> multipotenza<br />
Rated Voltage<br />
Tensione Nominale<br />
110 ÷ 127 V (3)<br />
220 ÷ 277 V<br />
Frequency<br />
Frequenza<br />
50...60 Hz<br />
AC Operation range<br />
Tensione di utilizzo AC<br />
198 ÷ 264 V<br />
DC Operation range<br />
Tensione di utilizzo DC<br />
<strong>17</strong>0 ÷ 280 V<br />
Power<br />
Potenza<br />
0 ÷ 20 W<br />
Maximum current<br />
output ripple<br />
Max. ondulazione<br />
della corrente uscita<br />
≤ 3% (1)<br />
Reference Norms<br />
Norme di riferimento:<br />
EN 50<strong>17</strong>2 (VDE 0108)<br />
EN 55015<br />
EN 60335-1<br />
EN 61000-3-2<br />
EN 61000-3-3<br />
EN 61347-1<br />
EN 61347-2-13<br />
EN 61547<br />
EN 62384<br />
VDE 0710-T14<br />
Article<br />
Articolo<br />
UNIVERSALE 20 WR<br />
UNIVERSALE 20 WR BI<br />
UNIVERSALE 20 WR<br />
Code<br />
Codice<br />
127140<br />
127142<br />
P out<br />
W<br />
V out<br />
DC<br />
I out<br />
DC<br />
n° <strong>LED</strong><br />
max. (1)<br />
V out<br />
max.<br />
ta<br />
°C<br />
tc<br />
°C l max. h max.<br />
Power Efficiency (1)<br />
Factor<br />
Constant current output - Uscita in corrente costante -25...+50 80 (2) 0,97 >88<br />
13 (13 (3) ) 10...54 250 mA cost. 16...18 59<br />
19 (15 (3) ) 2...54 350 mA cost. 16...18<br />
20 (15 (3) ) 2...50 400 mA cost. 15/16<br />
20 (15 (3) ) 2...44 450 mA cost. 12...14<br />
20 (15 (3) ) 2...40 500 mA cost. 11/12<br />
20 (15 (3) ) 2...37 550 mA cost. 10/11<br />
20 (15 (3) ) 2...34 600 mA cost. 9/10<br />
20 (15 (3) ) 2...29 700 mA cost. 8/9<br />
Constant voltage output - Uscita in tensione costante<br />
16 (15 (3) ) 24 cost. 700 mA max. - -<br />
(1)<br />
Referred to V in<br />
= 230 V, 100% load - Riferito a V in<br />
= 230 V, carico 100%<br />
(2)<br />
Tc = 75°C for Pout ≤16W<br />
AVAILABLE SOON<br />
Features<br />
• Multipower driver supplied with dip-switch for the selection of<br />
the output current.<br />
• IP20 independent driver, for indoor use (UNIVERSALE 20 WR).<br />
• Class II protection against electric shock for direct or indirect<br />
contact (UNIVERSALE 20 WR).<br />
• Driver for built-in use (UNIVERSALE 20 WR BI).<br />
• It can be used for lighting equipment in protection class I and II<br />
(UNIVERSALE 20 WR BI).<br />
• Active Power Factor Corrector.<br />
• Current regulation ±5 % including temperature variations.<br />
• Supplied with terminal cover and cable retainer.<br />
• Input and output terminal blocks on the same side (wire<br />
cross-section up to 1,5 mm 2 / AWG15).<br />
• Clamping screws on primary and secondary circuits for cables<br />
with diameter: min. 3 mm - max. 8 mm (UNIVERSALE 20 WR).<br />
• Driver can be secured with slot for screws.<br />
• Protections:<br />
- against overheating and short circuits;<br />
- against mains voltage spikes;<br />
- against overloads.<br />
• Thermal protection = C.5.a.<br />
• Double output impedance for use in household electrical<br />
appliances.<br />
UNIVERSALE 20 WR BI<br />
Caratteristiche<br />
• Alimentatore multipotenza fornito di dip-switch per la selezione<br />
della corrente in uscita.<br />
• Alimentatore indipendente IP20, per uso interno<br />
(UNIVERSALE 20 WR).<br />
• Protetto in classe II contro le scosse elettriche per contatti<br />
diretti e indiretti (UNIVERSALE 20 WR).<br />
• Alimentatore da incorporare (UNIVERSALE 20 WR BI).<br />
• Utilizzabile per apparecchi di illuminazione in classe di<br />
protezione I e II (UNIVERSALE 20 WR BI).<br />
• PFC attivo.<br />
• Corrente regolata ±5 % incluse variazioni di temperatura.<br />
• Fornito di coprimorsetto e serracavo.<br />
• Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino<br />
a 1,5 mm 2 / AWG15).<br />
• Serracavo su primario e secondario per cavi di diametro:<br />
min. 3 mm - max. 8 mm (UNIVERSALE 20 WR).<br />
• Fissaggio dell’alimentatore tramite asole per viti.<br />
• Protezioni:<br />
- termica e cortocircuito;<br />
- contro le extra-tensioni di rete;<br />
- contro i sovraccarichi.<br />
• Protezione termica = C.5.a.<br />
• Doppia impedenza d’uscita per l’utilizzo in apparecchi<br />
elettrodomestici.<br />
30 www.tci.it<br />
<strong>TCI</strong> professional <strong>LED</strong> applications