GUIDE TCI LED DRIVERS 2016-17
T-LED 80/350 1...10V SLIM Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications 05 RIPPLE FREE 3.2 Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili Rated Voltage Tensione Nominale 220 ÷ 240 V Frequency Frequenza 50...60 Hz AC Operation range Tensione di utilizzo AC 198 ÷ 264 V DC Operation range Tensione di utilizzo DC DC 176 ÷ 280 V (NO PUSH mode function) Power Potenza 4 ÷ 80 W Maximum current output ripple Max. ondulazione della corrente uscita ≤ 3% (1) Reference Norms Norme di riferimento: EN 50172 (VDE 0108) EN 55015 EN 61000-3-2 EN 61000-3-3 EN 61347-1 EN 61347-2-13 EN 61547 EN 62384 EN 62386 Article Articolo Code Codice P out W V out DC I out DC n° LED max. (1) V out max. ta °C tc °C l Power Factor h max. Efficiency (1) T-LED 80/350 1-10V SLIM 127080 35 30...250 140 mA cost. 80 300 -25...+55 80 0,95 (2) >93 38 30...250 155 mA cost. 80 42,5 30...250 170 mA cost. 80 46 30...250 185 mA cost. 80 50 30...250 200 mA cost. 80 53,5 30...250 215 mA cost. 80 57,5 30...250 230 mA cost. 80 61 30...250 245 mA cost. 80 65 30...250 260 mA cost. 80 68,5 30...250 275 mA cost. 80 72,5 30...250 290 mA cost. 80 76 30...250 305 mA cost. 75 80 30...250 320 mA cost. 75 80 30...235 335 mA cost. 70 80 30...228 350 mA cost. 70 (1) Referred to V in = 230 V, 100% load - Riferito a V in = 230 V, carico 100% (2) Pout>35W Features • Multipower driver supplied with dip-switch for the selection of the output current. • Driver for built-in use. • It can be used for lighting equipment in protection class I. • Active Power Factor Corrector. • Analogic input for thermal sensor connection. • Current regulation ±5 % including temperature variations. • Output is not isolated from the input. • Stand-by power less than 0,5 W. • Input and output terminal blocks on the opposite sides (wire cross-section up to 1,5 mm 2 / AWG15). • Protections: - against overheating and short circuits; - against mains voltage spikes; - against overloads. • Thermal protection = C.5.e. Caratteristiche • Alimentatore multipotenza fornito di dip-switch per la selezione della corrente in uscita. • Alimentatore da incorporare. • Utilizzabile per apparecchi di illuminazione in classe di protezione I. • PFC attivo. • Entrata analogica per sensore termico. • Corrente regolata ±5 % incluse variazioni di temperatura. • Uscita non isolata dall’ingresso. • Consumo in stand-by minore di 0,5 W. • Morsetti di entrata e uscita contrapposti (sezione cavo fino a 1,5 mm 2 / AWG15). • Protezioni: - termica e cortocircuito; - contro le extra-tensioni di rete; - contro i sovraccarichi. • Protezione termica = C.5.e. 196 www.tci.it TCI professional LED applications
T-LED 80/350 1...10V SLIM Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications Weight - Peso gr. 215 / 7,5 oz. Pcs - Pezzi 70 Compatible with ZHAGA (BL3/ZS7 H5D/ ZS7 H7D) 30 1,18’’ 350 13,78’’ 360 14,17’’ 21 0,83’’ 3.2 Wiring diagram - Schema di collegamento (Max. LED distance at page info8 - Massima distanza LED a pagina info8) Vin PUSH _ + 1-10 V PUSH L N PRI PUSH diagram - Collegamento PUSH 1 4 SEC + _ NTC SEC + _ LED 1-10 V Vin _ 1-10 V + PUSH L N PRI 1...10 V diagram - Collegamento 1...10 V 1 4 SEC + _ NTC + SEC _ LED Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili Operation Mode • Light regulation 10-100% by means of 1-10V (I=1mA) and 0/10-100% by means of PUSH function. • Specific dimming terminal connection with a 1...10 Vdc electronic potentiometer (1…10 V local dimming, double insulation required for external connection). • Light regulation 0/10 - 100 % by means of PUSH function (mains voltage): - a short push to turn on and off; - a longer push to increase or decrease light intensity; - regulation automatically stops at minimum and maximum values; - for another on, regulation or off command, release the push button and give the desired command again. • Possibility to use PUSH function to 4/5 drivers. • Maximum length of the cable, from push button to last driver, must be max. 15 m / 49 ft. In case of applications where the cable is longer than 15 m / 49 ft, keep this separate from the mains cable. • ATTENTION: only use normally open push buttons with no incorporated warning light. For additional details for regulations see pages info12-14. Modalità di funzionamento • Regolazione della luminosità 10-100 % mediante funzione 1-10 V (I=1 mA) e 0/10-100 % mediante funzione PUSH. • Provvisto di morsetto specifico per la regolazione collegando un potenziometro elettronico 1...10 Vdc (dimmerazione locale 1…10 V, per connessioni esterne all’apparecchio garantire il doppio isolamento). • Regolazione della luminosità 0/10 - 100% mediante la funzione PUSH (tensione di rete): - una pressione breve per accendere e spegnere; - una pressione prolungata per aumentare o diminuire l’intensità luminosa; - la regolazione si ferma automaticamente ai valori minimi e massimi; - per un nuovo comando accensione, regolazione o spegnimento, rilasciare il pulsante e dare nuovamente il comando desiderato. • Possibilità di utilizzo funzione PUSH fino a 4/5 alimentatori. • La lunghezza massima del cavo, dal pulsante all’ultimo trasformatore, deve essere max. 15 m / 49 ft. In caso di applicazioni dove il cavo superi i 15 m / 49 ft, tenere lo stesso separato dal cavo di rete. • ATTENZIONE: usare solo pulsanti di tipo normalmente aperto privi di spia luminosa incorporata. Per ulteriori dettagli sulle regolazioni vedi pagine info12-14. TCI professional LED applications www.tci.it 197
- Page 180 and 181: MAXI JOLLY HV DALI 50 Direct curren
- Page 182 and 183: MAXI JOLLY US TCM 50 - 1...10 V & P
- Page 184 and 185: MAXI JOLLY US DALI TCM 50 Direct cu
- Page 186 and 187: MAXI JOLLY HC 55 - 1...10 V & PUSH
- Page 188 and 189: MAXI JOLLY HC DALI 55 Direct curren
- Page 190 and 191: MAXI JOLLY HC TCM 55 - 1...10 V & P
- Page 192 and 193: MAXI JOLLY HC DALI TCM 55 Direct cu
- Page 194 and 195: MAXI JOLLY H 65 Direct current dimm
- Page 196 and 197: MAXI JOLLY DALI H 65 Direct current
- Page 198 and 199: MAXI JOLLY HTCM 65 Direct current d
- Page 200 and 201: MAXI JOLLY DALI HTCM 65 Direct curr
- Page 202 and 203: MAXI JOLLY DALI CR 50 Direct curren
- Page 204 and 205: DMX VST Direct current dimmable ele
- Page 206 and 207: RV LED professional led application
- Page 208 and 209: SUPERSLIM 1...10 V Direct current d
- Page 210 and 211: SUPERSLIM DALI Direct current dimma
- Page 212 and 213: SUPERFLAT DALI Direct current dimma
- Page 214 and 215: ATON 30/250-700 DALI Direct current
- Page 216 and 217: JOLLY SLIM 32 - 1...10 V & PUSH Dir
- Page 218 and 219: JOLLY SLIM HV 32 - 1...10 V & PUSH
- Page 220 and 221: MAXI JOLLY SLIM 60 - 1...10 V & PUS
- Page 222 and 223: MAXI JOLLY SLIM DALI 60 Direct curr
- Page 224 and 225: MAXI JOLLY SLIM HV 60 - 1...10 V &
- Page 226 and 227: MAXI JOLLY SLIM HV DALI 60 Direct c
- Page 228 and 229: MAXI JOLLY SLIM DALI 60 LS - LEDset
- Page 232 and 233: T-LED 80/500 1...10V SLIM Direct cu
- Page 234 and 235: T-LED 80/700 1...10V SLIM Direct cu
- Page 236 and 237: T-LED 80/350 DALI SLIM Direct curre
- Page 238 and 239: T-LED 80/500 DALI SLIM Direct curre
- Page 240 and 241: T-LED 80/700 DALI SLIM Direct curre
- Page 242 and 243: T-LED 90/580 DALI SLIM Direct curre
- Page 244 and 245: T-LED 80/500 DALI SLIM LS - LEDset2
- Page 246 and 247: professional led applications Made
- Page 248 and 249: SIRIO 150/200-700 Direct current di
- Page 250 and 251: SIRIO 150/300-1050 Direct current d
- Page 252 and 253: SIRIO 150/700 ST2 professional led
- Page 254 and 255: SIRIO 100 - 1...10 V & BILEVEL Dire
- Page 256 and 257: SIRIO 120/600-2100 - 1...10 V & BIL
- Page 258 and 259: SIRIO 150/200-700 - 1...10 V & BILE
- Page 260 and 261: SIRIO 150/300-1050 - 1...10 V & BIL
- Page 262 and 263: MAXI JOLLY US FP - FULL PROGRAMMABL
- Page 264 and 265: SIRIO 100/200-700 FP - FULL PROGRAM
- Page 266 and 267: SIRIO 150/200-700 FP - FULL PROGRAM
- Page 268 and 269: SIRIO 150/300-1050 FP - FULL PROGRA
- Page 270 and 271: POLARIS 150/200-700 FP - FULL PROGR
- Page 272 and 273: POLARIS 150/300-1050 FP - FULL PROG
- Page 274 and 275: DALI PROGRAMMER USB-DALI signal con
- Page 276 and 277: JOLLY AND MAXI JOLLY WITH CONFORMAL
- Page 278 and 279: 244 www.tci.it TCI professional LED
T-<strong>LED</strong> 80/350 1...10V SLIM<br />
Direct current dimmable electronic drivers with DIP-SWITCH<br />
Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH<br />
Made in Europe<br />
professional led applications<br />
05<br />
RIPPLE<br />
FREE<br />
3.2<br />
Dimmable multipower <strong>LED</strong> drivers<br />
Alimentatori <strong>LED</strong> multipotenza regolabili<br />
Rated Voltage<br />
Tensione Nominale<br />
220 ÷ 240 V<br />
Frequency<br />
Frequenza<br />
50...60 Hz<br />
AC Operation range<br />
Tensione di utilizzo AC<br />
198 ÷ 264 V<br />
DC Operation range<br />
Tensione di utilizzo DC<br />
DC <strong>17</strong>6 ÷ 280 V<br />
(NO PUSH mode<br />
function)<br />
Power<br />
Potenza<br />
4 ÷ 80 W<br />
Maximum current<br />
output ripple<br />
Max. ondulazione<br />
della corrente uscita<br />
≤ 3% (1)<br />
Reference Norms<br />
Norme di riferimento:<br />
EN 50<strong>17</strong>2 (VDE 0108)<br />
EN 55015<br />
EN 61000-3-2<br />
EN 61000-3-3<br />
EN 61347-1<br />
EN 61347-2-13<br />
EN 61547<br />
EN 62384<br />
EN 62386<br />
Article<br />
Articolo<br />
Code<br />
Codice<br />
P out<br />
W<br />
V out<br />
DC<br />
I out<br />
DC<br />
n° <strong>LED</strong><br />
max. (1)<br />
V out<br />
max.<br />
ta<br />
°C<br />
tc<br />
°C<br />
l<br />
Power<br />
Factor<br />
h max.<br />
Efficiency (1)<br />
T-<strong>LED</strong> 80/350 1-10V SLIM 127080 35 30...250 140 mA cost. 80 300 -25...+55 80 0,95 (2) >93<br />
38 30...250 155 mA cost. 80<br />
42,5 30...250 <strong>17</strong>0 mA cost. 80<br />
46 30...250 185 mA cost. 80<br />
50 30...250 200 mA cost. 80<br />
53,5 30...250 215 mA cost. 80<br />
57,5 30...250 230 mA cost. 80<br />
61 30...250 245 mA cost. 80<br />
65 30...250 260 mA cost. 80<br />
68,5 30...250 275 mA cost. 80<br />
72,5 30...250 290 mA cost. 80<br />
76 30...250 305 mA cost. 75<br />
80 30...250 320 mA cost. 75<br />
80 30...235 335 mA cost. 70<br />
80 30...228 350 mA cost. 70<br />
(1)<br />
Referred to V in<br />
= 230 V, 100% load - Riferito a V in<br />
= 230 V, carico 100%<br />
(2)<br />
Pout>35W<br />
Features<br />
• Multipower driver supplied with dip-switch for the selection<br />
of the output current.<br />
• Driver for built-in use.<br />
• It can be used for lighting equipment in protection class I.<br />
• Active Power Factor Corrector.<br />
• Analogic input for thermal sensor connection.<br />
• Current regulation ±5 % including temperature variations.<br />
• Output is not isolated from the input.<br />
• Stand-by power less than 0,5 W.<br />
• Input and output terminal blocks on the opposite sides<br />
(wire cross-section up to 1,5 mm 2 / AWG15).<br />
• Protections:<br />
- against overheating and short circuits;<br />
- against mains voltage spikes;<br />
- against overloads.<br />
• Thermal protection = C.5.e.<br />
Caratteristiche<br />
• Alimentatore multipotenza fornito di dip-switch per la selezione<br />
della corrente in uscita.<br />
• Alimentatore da incorporare.<br />
• Utilizzabile per apparecchi di illuminazione in classe di<br />
protezione I.<br />
• PFC attivo.<br />
• Entrata analogica per sensore termico.<br />
• Corrente regolata ±5 % incluse variazioni di temperatura.<br />
• Uscita non isolata dall’ingresso.<br />
• Consumo in stand-by minore di 0,5 W.<br />
• Morsetti di entrata e uscita contrapposti<br />
(sezione cavo fino a 1,5 mm 2 / AWG15).<br />
• Protezioni:<br />
- termica e cortocircuito;<br />
- contro le extra-tensioni di rete;<br />
- contro i sovraccarichi.<br />
• Protezione termica = C.5.e.<br />
196 www.tci.it<br />
<strong>TCI</strong> professional <strong>LED</strong> applications