GUIDE TCI LED DRIVERS 2016-17
JOLLY SLIM 32 - 1...10 V & PUSH Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications UL-CLASS2 CSA-LVLE 05 SELV RIPPLE FREE 3.2 Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili Rated Voltage Tensione Nominale 110 ÷ 120 V (2) 220 ÷ 240 V Frequency Frequenza 50...60 Hz AC Operation range Tensione di utilizzo AC 99 ÷ 264 V DC Operation range Tensione di utilizzo DC DC 176 ÷ 280 V (NO PUSH mode function) Power Potenza 0 ÷ 32 W Maximum current output ripple Max. ondulazione della corrente uscita ≤ 3% (1) Reference Norms Norme di riferimento: CSA 22.2 no. 250.13 EN 50172 (VDE 0108) EN 55015 EN 61000-3-2 EN 61000-3-3 EN 61347-1 EN 61347-2-13 EN 61547 EN 62384 UL 1310 UL 8750 VDE 0710-T14 Article Articolo Code Codice P out W V out DC I out DC n° LED max. (1) V out max. ta °C tc °C l max. h max. Power Efficiency (1) Factor DC JOLLY SLIM 122680 Constant current output - Uscita in corrente costante -25...+50 85 0,96 >87 17 (15 (2) ) 47 max. 350 mA cost. 12 53 24 (15 (2) ) 47 max. 500 mA cost. 12 32 (15 (2) ) 47 max. 700 mA cost. 12 Constant voltage output - Uscita in tensione costante 20 (15 (2) ) 24 cost. 900 mA max. - - (1) Referred to V in = 230 V, 100% load - Riferito a V in = 230 V, carico 100% Accessories not supplied - Accessori non a corredo Article - Articolo L (length) Code - Codice 1,5 m / 4 ft 485720512 Synchronization cable 4 m / 13 ft 485720513 Cavetto di sincronizzazione 50 cm / 19,68'' 485720515 20 cm / 7,87'' 485720516 IP67 protection cover Cover di protezione IP67 180066/390 REG 1-10 V (pag. 351) 123999L DCC DALI INTERFACE (pag. 328) 122099 BMU DMX INTERFACE (pag. 330) 122066 28 1,14’’ 415 16,34’’ 460 18,11’’ Features • Multipower driver supplied with dip-switch for the selection of the output current. • Driver for built-in use. • It can be used for lighting equipment in protection class I. • Active Power Factor Corrector. • Current regulation ±5 % including temperature variations. • Input and output terminal blocks on the opposite sides (wire cross-section up to 1,5 mm 2 / AWG15). • IP67 cover available upon request (code 180066/390). • Protections: - against overheating and short circuits; - against mains voltage spikes; - against overloads. 40 1,57’’ 41 1,61’’ Cover IP67 180066/390 (upon request - a richiesta disponibile) Caratteristiche • Alimentatore multipotenza fornito di dip-switch per la selezione della corrente in uscita. • Alimentatore da incorporare. • Utilizzabile per apparecchi di illuminazione in classe di protezione I. • PFC attivo. • Corrente regolata ±5 % incluse variazioni di temperatura. • Morsetti di entrata e uscita contrapposti (sezione cavo fino a 1,5 mm 2 / AWG15). • A richiesta disponibile versione con cover di protezione IP67 (codice 180066/390). • Protezioni: - termica e cortocircuito; - contro le extra-tensioni di rete; - contro i sovraccarichi. 182 www.tci.it TCI professional LED applications
JOLLY SLIM 32 - 1...10 V & PUSH Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications Weight - Peso gr. 110 / 3,88 oz. Pcs - Pezzi 50 30 1,18'' 220 8,66'' 237 9,33'' 21 0,83'' 3.2 Wiring diagram - Schema di collegamento (Max. LED distance on page info8 - Massima distanza LED a pagina info8) V in L N PRI OPTIONAL PUSH L SYNC SYNC max. 10 alimentatori in serie + _ + _ DIP SWITCH + _ max. 10 drivers in looping connection LED V in L PRI N OPTIONAL PUSH L SYNC SYNC max. 10 alimentatori in serie + _ + _ DIP SWITCH + _ max. 10 drivers in looping connection LED Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili V in L N PRI SYNC DIP SWITCH + + _ _ LED V in L N PRI DIP SWITCH + + SYNC _ _ LED PUSH L SYNC + _ PUSH L SYNC + _ + _ REG 1...10 V PUSH diagram - Collegamento PUSH 1...10 V diagram - Collegamento 1...10 V Operation Mode • Light regulation 0/0,5 - 100 % by means of PUSH function, 1...10 V interface (I = 0,35 mA) or 100 Kohm potentiometer. • Light regulation 0/0,5 - 100 % by means of PUSH function (L mains voltage; 170 Kohm): - a short push to turn on and off; - a longer push to increase or decrease light intensity; - regulation automatically stops at minimum and maximum values; - for another on, regulation or off command, release the push button and give the desired command again. • Maximum length of the cable, from push button to last driver, must be max. 15 m / 49 ft. In case of applications where the cable is longer than 15 m / 49 ft, keep this separate from the 110 - 240 Volt mains cable. • ATTENTION: only use normally open push buttons with no incorporated warning light. • Specific dimming terminal connection with a 1...10 Vdc electronic potentiometer (1…10 V local dimming, double insulation required for external connection). • Max. 10 synchronised drivers of which only one can be controlled (1 Master + 9 Slaves). • Synchronization cable is separately supplied. For additional details for regulations see pages info12-14. Modalità di funzionamento • Regolazione della luminosità 0/0,5 - 100 % mediante funzione PUSH, interfaccia 1...10 V (I = 0,35 mA) o potenziometro da 100 Kohm. • Regolazione della luminosità 0/0,5 - 100 % mediante la funzione PUSH (tensione di rete L; 170 Kohm): - una pressione breve per accendere e spegnere; - una pressione prolungata per aumentare o diminuire l’intensità luminosa; - la regolazione si ferma automaticamente ai valori minimi e massimi; - per un nuovo comando accensione, regolazione o spegnimento, rilasciare il pulsante e dare nuovamente il comando desiderato. • La lunghezza massima del cavo, dal pulsante all’ultimo trasformatore, deve essere max. 15 m / 49 ft. In caso di applicazioni dove il cavo superi i 15 m / 49 ft, tenere lo stesso separato dal cavo di rete 110 - 240 Volt. • ATTENZIONE: usare solo pulsanti di tipo normalmente aperto privi di spia luminosa incorporata. • Provvisto di morsetto specifico per la regolazione collegando un potenziometro elettronico 1...10 Vdc (dimmerazione locale 1…10 V, per connessioni esterne all’apparecchio garantire il doppio isolamento) • Max. 10 alimentatori sincronizzati, di cui uno solo comandato da uno o più punti (1 Master + 9 Slaves). • Cavetto per la sincronizzazione fornito separatamente. Per ulteriori dettagli sulle regolazioni vedi pagine info12-14. TCI professional LED applications www.tci.it 183
- Page 166 and 167: JOLLY DIN 32 Direct current dimmabl
- Page 168 and 169: MAXI JOLLY SV DALI 40 Direct curren
- Page 170 and 171: MAXI JOLLY US 50 - 1...10 V & PUSH
- Page 172 and 173: MAXI JOLLY US DALI 50 Direct curren
- Page 174 and 175: MAXI JOLLY SV - SELV 60 V - 1...10
- Page 176 and 177: MAXI JOLLY SV DALI - SELV 60 V Dire
- Page 178 and 179: MAXI JOLLY HV 50 - 1...10 V & PUSH
- Page 180 and 181: MAXI JOLLY HV DALI 50 Direct curren
- Page 182 and 183: MAXI JOLLY US TCM 50 - 1...10 V & P
- Page 184 and 185: MAXI JOLLY US DALI TCM 50 Direct cu
- Page 186 and 187: MAXI JOLLY HC 55 - 1...10 V & PUSH
- Page 188 and 189: MAXI JOLLY HC DALI 55 Direct curren
- Page 190 and 191: MAXI JOLLY HC TCM 55 - 1...10 V & P
- Page 192 and 193: MAXI JOLLY HC DALI TCM 55 Direct cu
- Page 194 and 195: MAXI JOLLY H 65 Direct current dimm
- Page 196 and 197: MAXI JOLLY DALI H 65 Direct current
- Page 198 and 199: MAXI JOLLY HTCM 65 Direct current d
- Page 200 and 201: MAXI JOLLY DALI HTCM 65 Direct curr
- Page 202 and 203: MAXI JOLLY DALI CR 50 Direct curren
- Page 204 and 205: DMX VST Direct current dimmable ele
- Page 206 and 207: RV LED professional led application
- Page 208 and 209: SUPERSLIM 1...10 V Direct current d
- Page 210 and 211: SUPERSLIM DALI Direct current dimma
- Page 212 and 213: SUPERFLAT DALI Direct current dimma
- Page 214 and 215: ATON 30/250-700 DALI Direct current
- Page 218 and 219: JOLLY SLIM HV 32 - 1...10 V & PUSH
- Page 220 and 221: MAXI JOLLY SLIM 60 - 1...10 V & PUS
- Page 222 and 223: MAXI JOLLY SLIM DALI 60 Direct curr
- Page 224 and 225: MAXI JOLLY SLIM HV 60 - 1...10 V &
- Page 226 and 227: MAXI JOLLY SLIM HV DALI 60 Direct c
- Page 228 and 229: MAXI JOLLY SLIM DALI 60 LS - LEDset
- Page 230 and 231: T-LED 80/350 1...10V SLIM Direct cu
- Page 232 and 233: T-LED 80/500 1...10V SLIM Direct cu
- Page 234 and 235: T-LED 80/700 1...10V SLIM Direct cu
- Page 236 and 237: T-LED 80/350 DALI SLIM Direct curre
- Page 238 and 239: T-LED 80/500 DALI SLIM Direct curre
- Page 240 and 241: T-LED 80/700 DALI SLIM Direct curre
- Page 242 and 243: T-LED 90/580 DALI SLIM Direct curre
- Page 244 and 245: T-LED 80/500 DALI SLIM LS - LEDset2
- Page 246 and 247: professional led applications Made
- Page 248 and 249: SIRIO 150/200-700 Direct current di
- Page 250 and 251: SIRIO 150/300-1050 Direct current d
- Page 252 and 253: SIRIO 150/700 ST2 professional led
- Page 254 and 255: SIRIO 100 - 1...10 V & BILEVEL Dire
- Page 256 and 257: SIRIO 120/600-2100 - 1...10 V & BIL
- Page 258 and 259: SIRIO 150/200-700 - 1...10 V & BILE
- Page 260 and 261: SIRIO 150/300-1050 - 1...10 V & BIL
- Page 262 and 263: MAXI JOLLY US FP - FULL PROGRAMMABL
- Page 264 and 265: SIRIO 100/200-700 FP - FULL PROGRAM
JOLLY SLIM 32 - 1...10 V & PUSH<br />
Direct current dimmable electronic drivers with DIP-SWITCH<br />
Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH<br />
Made in Europe<br />
professional led applications<br />
Weight - Peso gr. 110 / 3,88 oz.<br />
Pcs - Pezzi 50<br />
30<br />
1,18''<br />
220<br />
8,66''<br />
237<br />
9,33''<br />
21<br />
0,83''<br />
3.2<br />
Wiring diagram - Schema di collegamento (Max. <strong>LED</strong> distance on page info8 - Massima distanza <strong>LED</strong> a pagina info8)<br />
V in<br />
L<br />
N<br />
PRI<br />
OPTIONAL<br />
PUSH L<br />
SYNC<br />
SYNC<br />
max. 10<br />
alimentatori<br />
in serie<br />
+<br />
_<br />
+<br />
_<br />
DIP SWITCH<br />
+<br />
_<br />
max. 10 drivers<br />
in looping<br />
connection<br />
<strong>LED</strong><br />
V in<br />
L<br />
PRI<br />
N<br />
OPTIONAL<br />
PUSH L<br />
SYNC<br />
SYNC<br />
max. 10<br />
alimentatori<br />
in serie<br />
+<br />
_<br />
+<br />
_<br />
DIP SWITCH<br />
+<br />
_<br />
max. 10 drivers<br />
in looping<br />
connection<br />
<strong>LED</strong><br />
Dimmable multipower <strong>LED</strong> drivers<br />
Alimentatori <strong>LED</strong> multipotenza regolabili<br />
V in<br />
L<br />
N<br />
PRI<br />
SYNC<br />
DIP SWITCH<br />
+ +<br />
_ _<br />
<strong>LED</strong><br />
V in<br />
L<br />
N<br />
PRI<br />
DIP SWITCH<br />
+ +<br />
SYNC<br />
_ _<br />
<strong>LED</strong><br />
PUSH L<br />
SYNC<br />
+<br />
_<br />
PUSH L<br />
SYNC<br />
+<br />
_<br />
+<br />
_<br />
REG 1...10 V<br />
PUSH diagram - Collegamento PUSH<br />
1...10 V diagram - Collegamento 1...10 V<br />
Operation Mode<br />
• Light regulation 0/0,5 - 100 % by means of PUSH function, 1...10 V interface<br />
(I = 0,35 mA) or 100 Kohm potentiometer.<br />
• Light regulation 0/0,5 - 100 % by means of PUSH function (L mains voltage;<br />
<strong>17</strong>0 Kohm):<br />
- a short push to turn on and off;<br />
- a longer push to increase or decrease light intensity;<br />
- regulation automatically stops at minimum and maximum values;<br />
- for another on, regulation or off command, release the push button and give<br />
the desired command again.<br />
• Maximum length of the cable, from push button to last driver, must be<br />
max. 15 m / 49 ft. In case of applications where the cable is longer than<br />
15 m / 49 ft, keep this separate from the 110 - 240 Volt mains cable.<br />
• ATTENTION: only use normally open push buttons with no incorporated<br />
warning light.<br />
• Specific dimming terminal connection with a 1...10 Vdc electronic<br />
potentiometer (1…10 V local dimming, double insulation required for external<br />
connection).<br />
• Max. 10 synchronised drivers of which only one can be controlled<br />
(1 Master + 9 Slaves).<br />
• Synchronization cable is separately supplied.<br />
For additional details for regulations see pages info12-14.<br />
Modalità di funzionamento<br />
• Regolazione della luminosità 0/0,5 - 100 % mediante funzione PUSH,<br />
interfaccia 1...10 V (I = 0,35 mA) o potenziometro da 100 Kohm.<br />
• Regolazione della luminosità 0/0,5 - 100 % mediante la funzione PUSH<br />
(tensione di rete L; <strong>17</strong>0 Kohm):<br />
- una pressione breve per accendere e spegnere;<br />
- una pressione prolungata per aumentare o diminuire l’intensità luminosa;<br />
- la regolazione si ferma automaticamente ai valori minimi e massimi;<br />
- per un nuovo comando accensione, regolazione o spegnimento, rilasciare il<br />
pulsante e dare nuovamente il comando desiderato.<br />
• La lunghezza massima del cavo, dal pulsante all’ultimo trasformatore, deve<br />
essere max. 15 m / 49 ft. In caso di applicazioni dove il cavo superi i<br />
15 m / 49 ft, tenere lo stesso separato dal cavo di rete 110 - 240 Volt.<br />
• ATTENZIONE: usare solo pulsanti di tipo normalmente aperto privi di spia<br />
luminosa incorporata.<br />
• Provvisto di morsetto specifico per la regolazione collegando un<br />
potenziometro elettronico 1...10 Vdc (dimmerazione locale 1…10 V, per<br />
connessioni esterne all’apparecchio garantire il doppio isolamento)<br />
• Max. 10 alimentatori sincronizzati, di cui uno solo comandato da uno o più<br />
punti (1 Master + 9 Slaves).<br />
• Cavetto per la sincronizzazione fornito separatamente.<br />
Per ulteriori dettagli sulle regolazioni vedi pagine info12-14.<br />
<strong>TCI</strong> professional <strong>LED</strong> applications www.tci.it<br />
183