GUIDE TCI LED DRIVERS 2016-17
MAXI JOLLY US DALI 50 Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications 3.1 Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili (4) DAMP LOCATION 05 RIPPLE FREE DC MAXI JOLLY US DALI Rated Voltage Tensione Nominale 110 ÷ 127 V (2) Article Articolo Code Codice P out W V out DC I out DC 220 ÷ 240 V Frequency Frequenza 50...60 Hz AC Operation range Tensione di utilizzo AC 99 ÷ 264 V DC Operation range Tensione di utilizzo DC DC 170 ÷ 280 V DC MAXI JOLLY US DALI DC MAXI JOLLY US DALI BI 122413 122464 (NO PUSH mode function) (1) Referred to V in = 230 V, 100% load - Riferito a V in = 230 V, carico 100% (3) Only for DC MAXI JOLLY US (4) PUSH with memory function available on request Power (DC MAXI JOLLY US DALI M - 122301). Potenza 0 ÷ 50 W Maximum current output ripple Max. ondulazione della corrente uscita ≤ 3% (1) Reference Norms Norme di riferimento: CSA-C22.2 n° 107.1 (2) CSA-C22.2 n° 250.13 (2) EN 50172 (VDE 0108) EN 61000-3-2 EN 61000-3-3 EN 61347-1 EN 61347-2-13 EN 61547 Features • Multipower driver supplied with dip-switch for the selection of the output current. • IP20 independent driver, for indoor use (DC MAXI JOLLY US DALI). • Class II protection against electric shock for direct or indirect contact (DC MAXI JOLLY US DALI). • Driver for built-in use (DC MAXI JOLLY US BI DALI). • It can be used for lighting equipment in protection class I and II (DC MAXI JOLLY US BI DALI). EN 62384 • Active Power Factor Corrector. EN 62386-101 • Analogical input (NTC) for thermal sensor connection. EN 62386-102 • Auxiliary output 12 V max. 100 mA. • Current regulation ±5 % including temperature variations. EN 62386-207 • Input and output terminal blocks on the same side UL 1012 (2) (wire cross-section up to 2,5 mm 2 / AWG13). • Clamping screws on primary and secondary circuits for cables with diameter: min. 3 mm - max. 8 mm (DC MAXI JOLLY US DALI). • Protections: - against overheating and short circuits; - against mains voltage spikes; - against overloads. • Thermal protection = C.5.a. • Suitable for use on normally flammable surfaces; for the 900-1050 mA selections only at ta = 40°C according to the limits of IEC/EN 60598-1. (2) n° LED max. (1) DC MAXI JOLLY US DALI BI V out max. ta °C tc °C l max. h max. Power Efficiency (1) Factor 25 (25 (2) ) 74 max. 350 mA cost 20 90 -25...+50 85 0,95 > 89 35 (35 (2) ) 72 max. 500 mA cost. 20 39 (39 (2) ) 72 max. 550 mA cost. 20 46 (40 (2) ) 72 max. 650 mA cost. 18/20 50 (40 (2) ) 71 max. 700 mA cost. 18 50 (40 (2) ) 66 max. 750 mA cost. 16/18 50 (40 (2) ) 58 max. 850 mA cost. 16/18 -25...+45 50 (40 (2) ) 55 max. 900 mA cost. 16 50 (40 (2) ) 48 max. 1,05 A cost. 14 48Vout voltage limit settable with Dip-Switch - Poutmax=50W SELV Caratteristiche • Alimentatore multipotenza fornito di dip-switch per la selezione della corrente in uscita. • Alimentatore indipendente IP20, per uso interno (DC MAXI JOLLY US DALI). • Protetto in classe II contro le scosse elettriche per contatti diretti e indiretti (DC MAXI JOLLY US DALI). • Alimentatore da incorporare (DC MAXI JOLLY US BI DALI). • Utilizzabile per apparecchi di illuminazione in classe di protezione I e II (DC MAXI JOLLY US BI DALI). • PFC attivo. • Entrata analogica (NTC) per connessione sensore termico. • Uscita ausiliare 12 V max. 100 mA. • Corrente regolata ±5 % incluse variazioni di temperatura. • Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino a 2,5 mm 2 / AWG13). • Serracavo su primario e secondario per cavi di diametro: min. 3 mm - max. 8 mm (DC MAXI JOLLY US DALI). • Protezioni: - termica e cortocircuito; - contro le extra-tensioni di rete; - contro i sovraccarichi. • Protezione termica = C.5.a. • Ideneo ad utilizzo su superfici normalmente infiammabili; per selezioni 900-1050 mA solo a ta = 40°C in accordo ai limiti della IEC/EN 60598-1. (3) SAA-141682-EA (3) Accessories not supplied - Accessori non a corredo Article - Articolo L (length) Code - Codice 1,5 m / 4 ft 485720512 Synchronization cable 4 m / 13 ft 485720513 Cavetto di sincronizzazione 50 cm / 19,68'' 485720515 20 cm / 7,87'' 485720516 REG 1-10 V (pag. 351) 123999L BMU DMX INTERFACE (pag. 328) 122066 138 www.tci.it TCI professional LED applications
MAXI JOLLY US DALI 50 Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications Compatible with ZHAGA (AM3) 111 4,37’’ Ø84 3,31’’ Weight - Peso gr. 150 / 5,3 oz. Pcs - Pezzi 50 Compatible with ZHAGA (AM3) 111 4,37’’ Weight - Peso gr. 140 / 5,3 oz. Pcs - Pezzi 50 67 2,64’’ 79 3,11’’ 79 3,11’’ 67 2,64’’ 124 4,88’’ 22 0,87’’ 124 4,88’’ 22 0,87’’ 3.1 Wiring diagram - Schema di collegamento (Max. LED distance on page info8 - Massima distanza LED a pagina info8) 6 5 4 3 2 1 _ SEC + _ + SYNC _ _ + + PUSH N PRI L V aux LED Max. 10 alimentatori in serie Max. 10 drivers in looping connection 6 5 4 3 2 1 12 V AUX 6 5 4 3 2 1 _ SEC + _ + _ + _ + V aux LED 6 5 4 3 2 1 _ + SYNC _ _ + + PUSH Vin PRI N N Vin PRI L L Vin Max. 10 alimentatori in serie Max. 10 drivers in looping connection 6 5 4 3 2 1 12 V AUX _ SEC + V aux LED Max. 10 alimentatori in serie Max. 10 drivers in looping connection 6 5 4 3 2 1 12 V AUX Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili _ SEC + _ SYNC + _ + _ + _ + NTC V aux LED THERMAL SENSOR 12 V AUX _ SEC + _ 1...10 V + _ _ + + SYNC_ _ + + NTC V aux LED 1...10 V THERMAL SENSOR 12 V AUX _ SEC + _ SYNC + _ + _ + _ + NTC V aux LED THERMAL SENSOR 12 V AUX PUSH N PRI L PUSH Vin PRI N L Vin DA DA PUSH N PRI L DALI Vin PUSH diagram - Collegamento PUSH 1...10 V PUSH diagram - Collegamento 1...10 V DALI diagram - Collegamento DALI Operation Mode • Light regulation 0/0,5 - 100 % by means of PUSH function, 1...10 V interface (I=1 mA) or 100 Kohm potentiometer and DALI. • Features DALI dimming: - memory function for sets or light groups; - recall of stored functions; - compatible with standard DALI interfaces. • Light regulation 0/0,5 - 100 % by means of PUSH function (mains voltage): - a short push to turn on and off; - a longer push to increase or decrease light intensity; - regulation automatically stops at minimum and maximum values; - for another on, regulation or off command, release the push button and give the desired command again. • Possibility to use PUSH function to 4/5 drivers without sync cable. • Maximum length of the cable, from push button to last driver, must be max. 15 m / 49 ft. In case of applications where the cable is longer than 15 m / 49 ft, keep this separate from the 110 - 240 Volt mains cable. • ATTENTION: only use normally open push buttons with no incorporated warning light. • Specific dimming terminal connection with a 1...10 Vdc electronic potentiometer (1…10 V local dimming, double insulation required for external connection). • Max. 10 drivers synchronization, is possible command only one driver (1 Master + 9 Slaves). • Synchronization cable is separately supplied. For additional details for regulations see pages info12-14. Modalità di funzionamento • Regolazione della luminosità 0/0,5 - 100 % mediante funzione PUSH, interfaccia 1...10 V (I=1 mA) o potenziometro da 100 Kohm e DALI. • Caratteristiche della regolazione DALI: - funzione di memoria per scenari o gruppi luminosi; - richiamo di funzioni memorizzate; - compatibilità con interfacce DALI standard. • Regolazione della luminosità 0/0,5 - 100 % mediante la funzione PUSH (tensione di rete): - una pressione breve per accendere e spegnere; - una pressione prolungata per aumentare o diminuire l’intensità luminosa; - la regolazione si ferma automaticamente ai valori minimi e massimi; - per un nuovo comando accensione, regolazione o spegnimento, rilasciare il pulsante e dare nuovamente il comando desiderato. • Possibilità di utilizzo funzione PUSH fino a 4/5 alimentatori senza cavo di sincronismo. • La lunghezza massima del cavo, dal pulsante all’ultimo trasformatore, deve essere max. 15 m / 49 ft. In caso di applicazioni dove il cavo superi i 15 m / 49 ft, tenere lo stesso separato dal cavo di rete 110 - 240 Volt. • ATTENZIONE: usare solo pulsanti di tipo normalmente aperto privi di spia luminosa incorporata. • Provvisto di morsetto specifico per la regolazione collegando un potenziometro elettronico 1...10 Vdc (dimmerazione locale 1…10 V, per connessioni esterne all’apparecchio garantire il doppio isolamento). • Max. 10 alimentatori sincronizzati, di cui uno solo comandato da uno o più punti (1 Master + 9 Slaves). • Cavetto per la sincronizzazione fornito separatamente. Per ulteriori dettagli sulle regolazioni vedi pagine info12-14. TCI professional LED applications www.tci.it 139
- Page 122 and 123: professional led applications Made
- Page 124 and 125: MICRO JOLLY 6 - 1...10 V & PUSH Dir
- Page 126 and 127: MOONLIGHT 6 Direct current dimmable
- Page 128 and 129: RD57 - 1...10 V & PUSH Direct curre
- Page 130 and 131: MICRO MD professional led applicati
- Page 132 and 133: MINIJOLLY 20 - 1...10 V & PUSH Dire
- Page 134 and 135: MINIJOLLY DALI 20 professional led
- Page 136 and 137: MINIJOLLY LC 20 - 1...10 V & PUSH D
- Page 138 and 139: MINIJOLLY LC DALI 20 Direct current
- Page 140 and 141: MINIJOLLY HV Direct current dimmabl
- Page 142 and 143: MINIJOLED - 1...10 V & PUSH Direct
- Page 144 and 145: MINI MD Direct current dimmable (TR
- Page 146 and 147: JOLLY 25 - 1...10 V & PUSH Direct c
- Page 148 and 149: JOLLY HV 25 - 1...10 V & PUSH Direc
- Page 150 and 151: JOLLY PLUS - 1...10 V & PUSH Direct
- Page 152 and 153: JOLLY HV PLUS - 1...10 V & PUSH Dir
- Page 154 and 155: JOLLY US 32 - 1...10 V & PUSH Direc
- Page 156 and 157: JOLLY DALI 32 Direct current dimmab
- Page 158 and 159: JOLLY HC 39 - 1...10 V & PUSH Direc
- Page 160 and 161: PROFESSIONALE DALI 32 Direct curren
- Page 162 and 163: JOLLY MD 32 Direct current dimmable
- Page 164 and 165: WIDESQUARE R - 1...10 V & PUSH Dire
- Page 166 and 167: JOLLY DIN 32 Direct current dimmabl
- Page 168 and 169: MAXI JOLLY SV DALI 40 Direct curren
- Page 170 and 171: MAXI JOLLY US 50 - 1...10 V & PUSH
- Page 174 and 175: MAXI JOLLY SV - SELV 60 V - 1...10
- Page 176 and 177: MAXI JOLLY SV DALI - SELV 60 V Dire
- Page 178 and 179: MAXI JOLLY HV 50 - 1...10 V & PUSH
- Page 180 and 181: MAXI JOLLY HV DALI 50 Direct curren
- Page 182 and 183: MAXI JOLLY US TCM 50 - 1...10 V & P
- Page 184 and 185: MAXI JOLLY US DALI TCM 50 Direct cu
- Page 186 and 187: MAXI JOLLY HC 55 - 1...10 V & PUSH
- Page 188 and 189: MAXI JOLLY HC DALI 55 Direct curren
- Page 190 and 191: MAXI JOLLY HC TCM 55 - 1...10 V & P
- Page 192 and 193: MAXI JOLLY HC DALI TCM 55 Direct cu
- Page 194 and 195: MAXI JOLLY H 65 Direct current dimm
- Page 196 and 197: MAXI JOLLY DALI H 65 Direct current
- Page 198 and 199: MAXI JOLLY HTCM 65 Direct current d
- Page 200 and 201: MAXI JOLLY DALI HTCM 65 Direct curr
- Page 202 and 203: MAXI JOLLY DALI CR 50 Direct curren
- Page 204 and 205: DMX VST Direct current dimmable ele
- Page 206 and 207: RV LED professional led application
- Page 208 and 209: SUPERSLIM 1...10 V Direct current d
- Page 210 and 211: SUPERSLIM DALI Direct current dimma
- Page 212 and 213: SUPERFLAT DALI Direct current dimma
- Page 214 and 215: ATON 30/250-700 DALI Direct current
- Page 216 and 217: JOLLY SLIM 32 - 1...10 V & PUSH Dir
- Page 218 and 219: JOLLY SLIM HV 32 - 1...10 V & PUSH
- Page 220 and 221: MAXI JOLLY SLIM 60 - 1...10 V & PUS
MAXI JOLLY US DALI 50<br />
Direct current dimmable electronic drivers with DIP-SWITCH<br />
Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH<br />
Made in Europe<br />
professional led applications<br />
Compatible with ZHAGA (AM3)<br />
111<br />
4,37’’<br />
Ø84<br />
3,31’’<br />
Weight - Peso gr. 150 / 5,3 oz.<br />
Pcs - Pezzi 50<br />
Compatible with ZHAGA (AM3)<br />
111<br />
4,37’’<br />
Weight - Peso gr. 140 / 5,3 oz.<br />
Pcs - Pezzi 50<br />
67<br />
2,64’’<br />
79<br />
3,11’’<br />
79<br />
3,11’’<br />
67<br />
2,64’’<br />
124<br />
4,88’’<br />
22<br />
0,87’’<br />
124<br />
4,88’’<br />
22<br />
0,87’’<br />
3.1<br />
Wiring diagram - Schema di collegamento (Max. <strong>LED</strong> distance on page info8 - Massima distanza <strong>LED</strong> a pagina info8)<br />
6 5 4 3 2 1<br />
_<br />
SEC<br />
+<br />
_<br />
+<br />
SYNC _ _<br />
+ +<br />
PUSH<br />
N<br />
PRI<br />
L<br />
V aux<br />
<strong>LED</strong><br />
Max. 10 alimentatori in serie<br />
Max. 10 drivers in looping connection<br />
6 5 4 3 2 1<br />
12 V AUX<br />
6 5 4 3 2 1<br />
_<br />
SEC<br />
+<br />
_<br />
+<br />
_<br />
+<br />
_<br />
+ V aux<br />
<strong>LED</strong><br />
6 5 4 3 2 1<br />
_<br />
+<br />
SYNC _ _<br />
+ +<br />
PUSH<br />
Vin PRI<br />
N<br />
N<br />
Vin PRI<br />
L<br />
L<br />
Vin<br />
Max. 10 alimentatori in serie<br />
Max. 10 drivers in looping connection<br />
6 5 4 3 2 1<br />
12 V AUX<br />
_<br />
SEC<br />
+<br />
V aux<br />
<strong>LED</strong><br />
Max. 10 alimentatori in serie<br />
Max. 10 drivers in looping connection<br />
6 5 4 3 2 1<br />
12 V AUX<br />
Dimmable multipower <strong>LED</strong> drivers<br />
Alimentatori <strong>LED</strong> multipotenza regolabili<br />
_<br />
SEC<br />
+<br />
_<br />
SYNC + _<br />
+<br />
_<br />
+<br />
_<br />
+<br />
NTC<br />
V aux<br />
<strong>LED</strong><br />
THERMAL<br />
SENSOR<br />
12 V AUX<br />
_<br />
SEC<br />
+<br />
_<br />
1...10 V<br />
+<br />
_ _<br />
+ +<br />
SYNC_<br />
_<br />
+ +<br />
NTC<br />
V aux<br />
<strong>LED</strong><br />
1...10 V<br />
THERMAL<br />
SENSOR<br />
12 V AUX<br />
_<br />
SEC<br />
+<br />
_<br />
SYNC + _<br />
+<br />
_<br />
+<br />
_<br />
+<br />
NTC<br />
V aux<br />
<strong>LED</strong><br />
THERMAL<br />
SENSOR<br />
12 V AUX<br />
PUSH<br />
N<br />
PRI<br />
L<br />
PUSH<br />
Vin<br />
PRI<br />
N<br />
L<br />
Vin<br />
DA<br />
DA<br />
PUSH<br />
N<br />
PRI<br />
L<br />
DALI<br />
Vin<br />
PUSH diagram - Collegamento PUSH<br />
1...10 V PUSH diagram - Collegamento 1...10 V<br />
DALI diagram - Collegamento DALI<br />
Operation Mode<br />
• Light regulation 0/0,5 - 100 % by means of PUSH function, 1...10 V interface<br />
(I=1 mA) or 100 Kohm potentiometer and DALI.<br />
• Features DALI dimming:<br />
- memory function for sets or light groups;<br />
- recall of stored functions;<br />
- compatible with standard DALI interfaces.<br />
• Light regulation 0/0,5 - 100 % by means of PUSH function (mains voltage):<br />
- a short push to turn on and off;<br />
- a longer push to increase or decrease light intensity;<br />
- regulation automatically stops at minimum and maximum values;<br />
- for another on, regulation or off command, release the push button<br />
and give the desired command again.<br />
• Possibility to use PUSH function to 4/5 drivers without sync cable.<br />
• Maximum length of the cable, from push button to last driver, must be<br />
max. 15 m / 49 ft. In case of applications where the cable is longer than<br />
15 m / 49 ft, keep this separate from the 110 - 240 Volt mains cable.<br />
• ATTENTION: only use normally open push buttons with no incorporated<br />
warning light.<br />
• Specific dimming terminal connection with a 1...10 Vdc electronic<br />
potentiometer (1…10 V local dimming, double insulation required for external<br />
connection).<br />
• Max. 10 drivers synchronization, is possible command only one driver<br />
(1 Master + 9 Slaves).<br />
• Synchronization cable is separately supplied.<br />
For additional details for regulations see pages info12-14.<br />
Modalità di funzionamento<br />
• Regolazione della luminosità 0/0,5 - 100 % mediante funzione PUSH,<br />
interfaccia 1...10 V (I=1 mA) o potenziometro da 100 Kohm e DALI.<br />
• Caratteristiche della regolazione DALI:<br />
- funzione di memoria per scenari o gruppi luminosi;<br />
- richiamo di funzioni memorizzate;<br />
- compatibilità con interfacce DALI standard.<br />
• Regolazione della luminosità 0/0,5 - 100 % mediante la funzione PUSH<br />
(tensione di rete):<br />
- una pressione breve per accendere e spegnere;<br />
- una pressione prolungata per aumentare o diminuire l’intensità luminosa;<br />
- la regolazione si ferma automaticamente ai valori minimi e massimi;<br />
- per un nuovo comando accensione, regolazione o spegnimento, rilasciare<br />
il pulsante e dare nuovamente il comando desiderato.<br />
• Possibilità di utilizzo funzione PUSH fino a 4/5 alimentatori senza cavo<br />
di sincronismo.<br />
• La lunghezza massima del cavo, dal pulsante all’ultimo trasformatore,<br />
deve essere max. 15 m / 49 ft. In caso di applicazioni dove il cavo superi i<br />
15 m / 49 ft, tenere lo stesso separato dal cavo di rete 110 - 240 Volt.<br />
• ATTENZIONE: usare solo pulsanti di tipo normalmente aperto privi di spia<br />
luminosa incorporata.<br />
• Provvisto di morsetto specifico per la regolazione collegando un<br />
potenziometro elettronico 1...10 Vdc (dimmerazione locale 1…10 V, per<br />
connessioni esterne all’apparecchio garantire il doppio isolamento).<br />
• Max. 10 alimentatori sincronizzati, di cui uno solo comandato da uno<br />
o più punti (1 Master + 9 Slaves).<br />
• Cavetto per la sincronizzazione fornito separatamente.<br />
Per ulteriori dettagli sulle regolazioni vedi pagine info12-14.<br />
<strong>TCI</strong> professional <strong>LED</strong> applications www.tci.it<br />
139