GUIDE TCI LED DRIVERS 2016-17
JOLLY HC 39 - 1...10 V & PUSH Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications SELV RIPPLE FREE 3.1 DC JOLLY HC DC JOLLY HC BI Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili Rated Voltage Tensione Nominale 220 ÷ 240 V Frequency Frequenza 50...60 Hz AC Operation range Tensione di utilizzo AC 198 ÷ 264 V DC Operation range Tensione di utilizzo DC 170 ÷ 280 V (NO PUSH mode function) Power out Potenza uscita 0 ÷ 39 W Maximum current output ripple Max. ondulazione della corrente uscita ≤ 3% (1) Reference Norms Norme di riferimento: EN 50172 (VDE 0108) EN 55015 EN 61000-3-2 EN 61000-3-3 EN 61347-1 EN 61347-2-13 EN 61547 EN 62384 VDE 0710-T14 Article Code P out V out I out n° LED V out ta tc l max. h max. Articolo Codice W DC DC max. (1) max. °C °C Power Efficiency (1) Factor DC JOLLY HC MV 127021 15 42 max. 350 mA cost 12...14 55 -25...+50 80 0,95 > 90 DC JOLLY HC BI 127022 21 42 max. 500 mA cost. 12...14 23 42 max. 550 mA cost. 12 27 42 max. 650 mA cost. 10/11 29 42 max. 700 mA cost. 10/11 31 42 max. 750 mA cost. 9/10 35 42 max. 850 mA cost. 9/10 37 42 max. 900 mA cost. 9/10 -25...+45 39 37 max. 1,05 A cost. 8/9 (1) Referred to V in = 230 V, 100% load - Riferito a V in = 230 V, carico 100% Accessories not supplied - Accessori non a corredo Article - Articolo L (length) Code - Codice 1,5 m / 4 ft 485720512 Synchronization cable 4 m / 13 ft 485720513 Cavetto di sincronizzazione 50 cm / 19,68'' 485720515 20 cm / 7,87'' 485720516 REG 1-10 V (pag. 351) 123999L DCC DALI INTERFACE (pag. 328) 122099 BMU DMX INTERFACE (pag. 330) 122066 Features • Multipower driver supplied with dip-switch for the selection of the output current and voltage. • IP20 independent driver, for indoor use (DC JOLLY HC). • Class II protection against electric shock for direct or indirect contact (DC JOLLY HC). • Driver for built-in use (DC JOLLY HC BI). • It can be used for lighting equipment in protection class I and II (DC JOLLY HC BI). • Active Power Factor Corrector. • Current regulation ±5 % including temperature variations. • Input and output terminal blocks on the same side (wire cross-section up to 1,5-2,5 mm 2 / AWG15 - AWG13). • Clamping screws on primary and secondary circuits for cables with diameter: min. 3 mm - max. 8 mm (DC JOLLY HC). • Protections: - against overheating and short circuits; - against mains voltage spikes; - against overloads. • Thermal protection = C.5.a. Caratteristiche • Alimentatore multipotenza fornito di dip-switch per la selezione della corrente e della tensione in uscita. • Alimentatore indipendente IP20, per uso interno (DC JOLLY HC). • Protetto in classe II contro le scosse elettriche per contatti diretti e indiretti (DC JOLLY HC). • Alimentatore da incorporare (DC JOLLY HC BI). • Utilizzabile per apparecchi di illuminazione in classe di protezione I e II (DC JOLLY HC BI). • PFC attivo. • Corrente regolata ±5 % incluse variazioni di temperatura. • Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino a 1,5-2,5 mm 2 / AWG15 - AWG13). • Serracavo su primario e secondario per cavi di diametro: min. 3 mm - max. 8 mm (DC JOLLY HC). • Protezioni: - termica e cortocircuito; - contro le extra-tensioni di rete; - contro i sovraccarichi. • Protezione termica = C.5.a. 124 www.tci.it TCI professional LED applications
JOLLY HC 39 - 1...10 V & PUSH Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications Compatible with ZHAGA (AS1) 93,5 3,68’’ Ø72 2,83'' Weight - Peso gr. 120 / 4,20 oz. Pcs - Pezzi 50 Compatible with ZHAGA (AS1) 93,5 3,68’’ Weight - Peso gr. 100 / 3,50 oz. Pcs - Pezzi 50 57,5 2,26’’ 67 2,63’’ 57,5 2,26’’ 67 2,63’’ 103 4,06’’ 21 0,83’’ 90 3,54’’ 21 0,83’’ 3.1 Wiring diagram - Schema di collegamento (Max. LED distance on page info8 - Massima distanza LED a pagina info8) DIP-SWITCH + SYNC _ + _ SEC 1...10 V + _ + _ PUSH N PRI L Max. 10 drivers in looping connection Max. 10 alimentatori in serie SYNC SYNC LED Vin DIP-SWITCH + SYNC _ + _ SEC 1...10 V + _ + _ PUSH N PRI L Max. 10 drivers in looping connection Max. 10 alimentatori in serie SYNC LED Vin SYNC Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili DIP-SWITCH DIP-SWITCH SYNC _ + _ + + SYNC _ + _ SEC + _ LED SEC + _ LED 1...10 V + _ PUSH N PRI L PUSH Vin 1...10 V + _ PUSH N PRI L 1...10 V Vin PUSH diagram - Collegamento PUSH 1...10 V diagram - Collegamento 1...10 V Operation Mode • Light regulation 0/0,5 - 100 % by means of PUSH function, 1...10 V interface (I=1 mA) or 100 Kohm potentiometer. • Light regulation 0/0,5 - 100 % by means of PUSH function (L mains voltage: 170 Kohm): - a short push to turn on and off; - a longer push to increase or decrease light intensity; - regulation automatically stops at minimum and maximum values; - for another on, regulation or off command, release the push button and give the desired command again. • Possibility to use PUSH function to 4/5 drivers without sync cable. • Maximum length of the cables, from push button to last driver, must be max. 15 m / 49 ft. In case of applications where the cable is longer than 15 m / 49 ft, keep this separate from the 110 - 240 Volt mains cable. • ATTENTION: only use normally open push buttons with no incorporated warning light. • Specific dimming terminal connection with a 1...10 Vdc electronic potentiometer (1…10 V local dimming, double insulation required for external connection). • Max. 10 synchronised drivers of which only one can be controlled (1 Master + 9 Slaves of any JOLLY Series). • Synchronization cable is separately supplied. • Regulation is possible by means of DALI and DMX coupled with DALI/DMX INTERFACE (pages 328-330). For additional details for regulations see pages info12-14. Modalità di funzionamento • Regolazione della luminosità 0/0,5 - 100 % mediante funzione PUSH, interfaccia 1...10 V (I=1 mA) o potenziometro da 100 Kohm. • Regolazione della luminosità 0/0,5 - 100 % mediante la funzione PUSH (tensione di rete L; 170 Kohm): - una pressione breve per accendere e spegnere; - una pressione prolungata per aumentare o diminuire l’intensità luminosa; - la regolazione si ferma automaticamente ai valori minimi e massimi; - per un nuovo comando accensione, regolazione o spegnimento, rilasciare il pulsante e dare nuovamente il comando desiderato. • Possibilità di utilizzo funzione PUSH fino a 4/5 alimentatori senza cavo di sincronismo. • La lunghezza massima dei cavi, dal pulsante all’ultimo trasformatore, deve essere max. 15 m / 49 ft. In caso di applicazioni dove il cavo superi i 15 m / 49 ft, tenere lo stesso separato dal cavo di rete 110 - 240 Volt. • ATTENZIONE: usare solo pulsanti di tipo normalmente aperto privi di spia luminosa incorporata. • Provvisto di morsetto specifico per la regolazione collegando un potenziometro elettronico 1...10 Vdc (dimmerazione locale 1…10 V, per connessioni esterne all’apparecchio garantire il doppio isolamento). • Max. 10 alimentatori sincronizzati, di cui uno solo comandato da uno o più punti (1 Master + 9 Slaves qualsiasi driver della Serie JOLLY). • Cavetto per la sincronizzazione fornito separatamente. • La regolazione DALI e DMX è possibile tramite DALI/DMX INTERFACE (pagine 328-330). Per ulteriori dettagli sulle regolazioni vedi pagine info12-14. TCI professional LED applications www.tci.it 125
- Page 108 and 109: ATON 30/700-1400 Direct current ele
- Page 110 and 111: MP 32 SLIM Direct current electroni
- Page 112 and 113: MP 60 SLIM Direct current electroni
- Page 114 and 115: SMART 70 HC SLIM Direct current ele
- Page 116 and 117: MP 50/350 SLIM Direct current elect
- Page 118 and 119: MP 80/500 SLIM Direct current elect
- Page 120 and 121: MP 80/500 SLIM LS - LEDset2 Direct
- Page 122 and 123: professional led applications Made
- Page 124 and 125: MICRO JOLLY 6 - 1...10 V & PUSH Dir
- Page 126 and 127: MOONLIGHT 6 Direct current dimmable
- Page 128 and 129: RD57 - 1...10 V & PUSH Direct curre
- Page 130 and 131: MICRO MD professional led applicati
- Page 132 and 133: MINIJOLLY 20 - 1...10 V & PUSH Dire
- Page 134 and 135: MINIJOLLY DALI 20 professional led
- Page 136 and 137: MINIJOLLY LC 20 - 1...10 V & PUSH D
- Page 138 and 139: MINIJOLLY LC DALI 20 Direct current
- Page 140 and 141: MINIJOLLY HV Direct current dimmabl
- Page 142 and 143: MINIJOLED - 1...10 V & PUSH Direct
- Page 144 and 145: MINI MD Direct current dimmable (TR
- Page 146 and 147: JOLLY 25 - 1...10 V & PUSH Direct c
- Page 148 and 149: JOLLY HV 25 - 1...10 V & PUSH Direc
- Page 150 and 151: JOLLY PLUS - 1...10 V & PUSH Direct
- Page 152 and 153: JOLLY HV PLUS - 1...10 V & PUSH Dir
- Page 154 and 155: JOLLY US 32 - 1...10 V & PUSH Direc
- Page 156 and 157: JOLLY DALI 32 Direct current dimmab
- Page 160 and 161: PROFESSIONALE DALI 32 Direct curren
- Page 162 and 163: JOLLY MD 32 Direct current dimmable
- Page 164 and 165: WIDESQUARE R - 1...10 V & PUSH Dire
- Page 166 and 167: JOLLY DIN 32 Direct current dimmabl
- Page 168 and 169: MAXI JOLLY SV DALI 40 Direct curren
- Page 170 and 171: MAXI JOLLY US 50 - 1...10 V & PUSH
- Page 172 and 173: MAXI JOLLY US DALI 50 Direct curren
- Page 174 and 175: MAXI JOLLY SV - SELV 60 V - 1...10
- Page 176 and 177: MAXI JOLLY SV DALI - SELV 60 V Dire
- Page 178 and 179: MAXI JOLLY HV 50 - 1...10 V & PUSH
- Page 180 and 181: MAXI JOLLY HV DALI 50 Direct curren
- Page 182 and 183: MAXI JOLLY US TCM 50 - 1...10 V & P
- Page 184 and 185: MAXI JOLLY US DALI TCM 50 Direct cu
- Page 186 and 187: MAXI JOLLY HC 55 - 1...10 V & PUSH
- Page 188 and 189: MAXI JOLLY HC DALI 55 Direct curren
- Page 190 and 191: MAXI JOLLY HC TCM 55 - 1...10 V & P
- Page 192 and 193: MAXI JOLLY HC DALI TCM 55 Direct cu
- Page 194 and 195: MAXI JOLLY H 65 Direct current dimm
- Page 196 and 197: MAXI JOLLY DALI H 65 Direct current
- Page 198 and 199: MAXI JOLLY HTCM 65 Direct current d
- Page 200 and 201: MAXI JOLLY DALI HTCM 65 Direct curr
- Page 202 and 203: MAXI JOLLY DALI CR 50 Direct curren
- Page 204 and 205: DMX VST Direct current dimmable ele
- Page 206 and 207: RV LED professional led application
JOLLY HC 39 - 1...10 V & PUSH<br />
Direct current dimmable electronic drivers with DIP-SWITCH<br />
Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH<br />
Made in Europe<br />
professional led applications<br />
SELV<br />
RIPPLE<br />
FREE<br />
3.1<br />
DC JOLLY HC<br />
DC JOLLY HC BI<br />
Dimmable multipower <strong>LED</strong> drivers<br />
Alimentatori <strong>LED</strong> multipotenza regolabili<br />
Rated Voltage<br />
Tensione Nominale<br />
220 ÷ 240 V<br />
Frequency<br />
Frequenza<br />
50...60 Hz<br />
AC Operation range<br />
Tensione di utilizzo AC<br />
198 ÷ 264 V<br />
DC Operation range<br />
Tensione di utilizzo DC<br />
<strong>17</strong>0 ÷ 280 V<br />
(NO PUSH mode<br />
function)<br />
Power out<br />
Potenza uscita<br />
0 ÷ 39 W<br />
Maximum current<br />
output ripple<br />
Max. ondulazione<br />
della corrente uscita<br />
≤ 3% (1)<br />
Reference Norms<br />
Norme di riferimento:<br />
EN 50<strong>17</strong>2 (VDE 0108)<br />
EN 55015<br />
EN 61000-3-2<br />
EN 61000-3-3<br />
EN 61347-1<br />
EN 61347-2-13<br />
EN 61547<br />
EN 62384<br />
VDE 0710-T14<br />
Article<br />
Code P out V out I out n° <strong>LED</strong> V out ta tc l max. h max.<br />
Articolo<br />
Codice W DC<br />
DC max. (1) max. °C °C Power Efficiency (1)<br />
Factor<br />
DC JOLLY HC MV 127021 15 42 max. 350 mA cost 12...14 55 -25...+50 80 0,95 > 90<br />
DC JOLLY HC BI 127022<br />
21 42 max. 500 mA cost. 12...14<br />
23 42 max. 550 mA cost. 12<br />
27 42 max. 650 mA cost. 10/11<br />
29 42 max. 700 mA cost. 10/11<br />
31 42 max. 750 mA cost. 9/10<br />
35 42 max. 850 mA cost. 9/10<br />
37 42 max. 900 mA cost. 9/10 -25...+45<br />
39 37 max. 1,05 A cost. 8/9<br />
(1)<br />
Referred to V in<br />
= 230 V, 100% load - Riferito a V in<br />
= 230 V, carico 100%<br />
Accessories not supplied - Accessori non a corredo<br />
Article - Articolo L (length) Code - Codice<br />
1,5 m / 4 ft 485720512<br />
Synchronization cable<br />
4 m / 13 ft 485720513<br />
Cavetto di sincronizzazione 50 cm / 19,68'' 485720515<br />
20 cm / 7,87'' 485720516<br />
REG 1-10 V (pag. 351)<br />
123999L<br />
DCC DALI INTERFACE (pag. 328) 122099<br />
BMU DMX INTERFACE (pag. 330) 122066<br />
Features<br />
• Multipower driver supplied with dip-switch for the selection of<br />
the output current and voltage.<br />
• IP20 independent driver, for indoor use (DC JOLLY HC).<br />
• Class II protection against electric shock for direct or indirect<br />
contact (DC JOLLY HC).<br />
• Driver for built-in use (DC JOLLY HC BI).<br />
• It can be used for lighting equipment in protection class I and II<br />
(DC JOLLY HC BI).<br />
• Active Power Factor Corrector.<br />
• Current regulation ±5 % including temperature variations.<br />
• Input and output terminal blocks on the same side (wire<br />
cross-section up to 1,5-2,5 mm 2 / AWG15 - AWG13).<br />
• Clamping screws on primary and secondary circuits for cables<br />
with diameter: min. 3 mm - max. 8 mm (DC JOLLY HC).<br />
• Protections:<br />
- against overheating and short circuits;<br />
- against mains voltage spikes;<br />
- against overloads.<br />
• Thermal protection = C.5.a.<br />
Caratteristiche<br />
• Alimentatore multipotenza fornito di dip-switch per la selezione<br />
della corrente e della tensione in uscita.<br />
• Alimentatore indipendente IP20, per uso interno (DC JOLLY HC).<br />
• Protetto in classe II contro le scosse elettriche per contatti<br />
diretti e indiretti (DC JOLLY HC).<br />
• Alimentatore da incorporare (DC JOLLY HC BI).<br />
• Utilizzabile per apparecchi di illuminazione in classe di<br />
protezione I e II (DC JOLLY HC BI).<br />
• PFC attivo.<br />
• Corrente regolata ±5 % incluse variazioni di temperatura.<br />
• Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino<br />
a 1,5-2,5 mm 2 / AWG15 - AWG13).<br />
• Serracavo su primario e secondario per cavi di diametro:<br />
min. 3 mm - max. 8 mm (DC JOLLY HC).<br />
• Protezioni:<br />
- termica e cortocircuito;<br />
- contro le extra-tensioni di rete;<br />
- contro i sovraccarichi.<br />
• Protezione termica = C.5.a.<br />
124 www.tci.it<br />
<strong>TCI</strong> professional <strong>LED</strong> applications