GUIDE TCI LED DRIVERS 2016-17
JOLLY 25 - 1...10 V & PUSH Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications 05 SELV RIPPLE FREE 3.1 Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili Rated Voltage Tensione Nominale 110 ÷ 120 V (2) 220 ÷ 240 V Frequency Frequenza 50...60 Hz AC Operation range Tensione di utilizzo AC 99 ÷ 264 V DC Operation range Tensione di utilizzo DC 176 ÷ 264 V (NO PUSH mode function) Power Potenza 0 ÷ 25 W Maximum current output ripple Max. ondulazione della corrente uscita ≤ 3% (1) Reference Norms Norme di riferimento: EN 50172 (VDE 0108) EN 55015 EN 61000-3-2 EN 61000-3-3 EN 61347-1 EN 61347-2-13 EN 61547 EN 62384 VDE 0710-T14 Article Articolo Code Codice P out W V out DC I out DC n° LED max. (1) V out max. ta °C tc °C l max. h max. Power Efficiency (1) Factor DC JOLLY 122420 Constant current output - Uscita in corrente costante -25...+50 75 0,98 > 87 15 (15 (2) ) 43 max. 350 mA cost. 12 49 22 (15 (2) ) 43 max. 500 mA cost. 11/12 25 (15 (2) ) 36 max. 700 mA cost. 9 Constant voltage output - Uscita in tensione costante 9 (9 (2) ) 10 cost. 900 mA max. - - 10 (10 (2) ) 12 cost. 900 mA max. - - 20 (15 (2) ) 24 cost. 900 mA max. - - (1) Referred to V in = 230 V, 100% load - Riferito a V in = 230 V, carico 100% Features • Multipower driver supplied with dip-switch for the selection of the output current. • IP20 independent driver, for indoor use. • Class II protection against electric shock for direct or indirect contact. • Active Power Factor Corrector. • Current regulation ±5 % including temperature variations. • Input and output terminal blocks on the same side (wire cross-section up to 1,5 mm 2 / AWG15). • Clamping screws on primary and secondary circuits for cables with diameter: min. 3 mm - max. 8 mm. • Protections: - against overheating and short circuits; - against mains voltage spikes; - against overloads. • Thermal protection = C.5.a. Accessories not supplied - Accessori non a corredo Article - Articolo L (length) Code - Codice 1,5 m / 4 ft 485720512 Synchronization cable 4 m / 13 ft 485720513 Cavetto di sincronizzazione 50 cm / 19,68'' 485720515 20 cm / 7,87'' 485720516 REG 1-10 V (pag. 351) 123999L DCC DALI INTERFACE (pag. 328) 122099 BMU DMX INTERFACE (pag. 330) 122066 Caratteristiche • Alimentatore multipotenza fornito di dip-switch per la selezione della corrente in uscita. • Alimentatore indipendente IP20, per uso interno. • Protetto in classe II contro le scosse elettriche per contatti diretti e indiretti. • PFC attivo. • Corrente regolata ±5 % incluse variazioni di temperatura. • Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino a 1,5 mm 2 / AWG15). • Serracavo su primario e secondario per cavi di diametro: min. 3 mm - max. 8 mm. • Protezioni: - termica e cortocircuito; - contro le extra-tensioni di rete; - contro i sovraccarichi. • Protezione termica = C.5.a. 112 www.tci.it TCI professional LED applications
JOLLY 25 - 1...10 V & PUSH Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications Compatible with ZHAGA (AS1) 93,5 3,68’’ Ø72 2,83'' Weight - Peso gr. 120 / 4,20 oz. Pcs - Pezzi 50 57,5 2,26’’ 67 2,63’’ 103 4,06’’ 21 0,83’’ 3.1 Wiring diagram - Schema di collegamento (Max. LED distance on page info8 - Massima distanza LED a pagina info8) DIP-SWITCH + SYNC _ + _ SEC 1...10 V + _ + _ PUSH N PRI L Max. 10 drivers in looping connection Max. 10 alimentatori in serie SYNC SYNC LED Vin DIP-SWITCH + SYNC _ + _ SEC 1...10 V + _ + _ PUSH N PRI L Max. 10 drivers in looping connection Max. 10 alimentatori in serie SYNC LED Vin SYNC Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili DIP-SWITCH DIP-SWITCH SYNC _ + _ + + SYNC _ + _ SEC + _ LED SEC + _ LED 1...10 V + _ PUSH N PRI L PUSH Vin 1...10 V + _ PUSH N PRI L 1...10 V Vin PUSH diagram - Collegamento PUSH 1...10 V diagram - Collegamento 1...10 V Operation Mode • Light regulation 0/0,5 - 100 % by means of PUSH function, 1...10 V interface (I=0,35 mA) or 100 Kohm potentiometer. • Light regulation 0/0,5 - 100 % by means of PUSH function (L mains voltage: 170 Kohm): - a short push to turn on and off; - a longer push to increase or decrease light intensity; - regulation automatically stops at minimum and maximum values; - for another on, regulation or off command, release the push button and give the desired command again. • Possibility to use PUSH function to 4/5 drivers without sync cable. • Maximum length of the cable, from push button to last driver, must be max. 15 m / 49 ft. In case of applications where the cable is longer than 15 m / 49 ft, keep this separate from the 110 - 240 Volt mains cable. • ATTENTION: only use normally open push buttons with no incorporated warning light. • Specific dimming terminal connection with a 1...10 Vdc electronic potentiometer (1…10 V local dimming, double insulation required for external connection). • Max. 10 synchronised drivers of which only one can be controlled (1 Master + 9 Slaves). • Synchronization cable is separately supplied. For additional details for regulations see pages info12-14. Modalità di funzionamento • Regolazione della luminosità 0/0,5 - 100 % mediante funzione PUSH, interfaccia 1...10 V (I=0,35 mA) o potenziometro da 100 Kohm. • Regolazione della luminosità 0/0,5 - 100 % mediante la funzione PUSH (tensione di rete L; 170 Kohm): - una pressione breve per accendere e spegnere; - una pressione prolungata per aumentare o diminuire l’intensità luminosa; - la regolazione si ferma automaticamente ai valori minimi e massimi; - per un nuovo comando accensione, regolazione o spegnimento, rilasciare il pulsante e dare nuovamente il comando desiderato. • Possibilità di utilizzo funzione PUSH fino a 4/5 alimentatori senza cavo di sincronismo. • La lunghezza massima del cavo, dal pulsante all’ultimo trasformatore, deve essere max. 15 m / 49 ft. In caso di applicazioni dove il cavo superi i 15 m / 49 ft, tenere lo stesso separato dal cavo di rete 110 - 240 Volt. • ATTENZIONE: usare solo pulsanti di tipo normalmente aperto privi di spia luminosa incorporata. • Provvisto di morsetto specifico per la regolazione collegando un potenziometro elettronico 1...10 Vdc (dimmerazione locale 1…10 V, per connessioni esterne all’apparecchio garantire il doppio isolamento). • Max. 10 alimentatori sincronizzati, di cui uno solo comandato da uno o più punti (1 Master + 9 Slaves). • Cavetto per la sincronizzazione fornito separatamente. Per ulteriori dettagli sulle regolazioni vedi pagine info12-14. TCI professional LED applications www.tci.it 113
- Page 96 and 97: MP 55 / 120 HC Direct current elect
- Page 98 and 99: MP 65 H Direct current electronic d
- Page 100 and 101: MP 65 HTCM Direct current electroni
- Page 102 and 103: SMART 70 Direct current electronic
- Page 104 and 105: SUPERSLIM Direct current electronic
- Page 106 and 107: ATON 30/250-700 Direct current elec
- Page 108 and 109: ATON 30/700-1400 Direct current ele
- Page 110 and 111: MP 32 SLIM Direct current electroni
- Page 112 and 113: MP 60 SLIM Direct current electroni
- Page 114 and 115: SMART 70 HC SLIM Direct current ele
- Page 116 and 117: MP 50/350 SLIM Direct current elect
- Page 118 and 119: MP 80/500 SLIM Direct current elect
- Page 120 and 121: MP 80/500 SLIM LS - LEDset2 Direct
- Page 122 and 123: professional led applications Made
- Page 124 and 125: MICRO JOLLY 6 - 1...10 V & PUSH Dir
- Page 126 and 127: MOONLIGHT 6 Direct current dimmable
- Page 128 and 129: RD57 - 1...10 V & PUSH Direct curre
- Page 130 and 131: MICRO MD professional led applicati
- Page 132 and 133: MINIJOLLY 20 - 1...10 V & PUSH Dire
- Page 134 and 135: MINIJOLLY DALI 20 professional led
- Page 136 and 137: MINIJOLLY LC 20 - 1...10 V & PUSH D
- Page 138 and 139: MINIJOLLY LC DALI 20 Direct current
- Page 140 and 141: MINIJOLLY HV Direct current dimmabl
- Page 142 and 143: MINIJOLED - 1...10 V & PUSH Direct
- Page 144 and 145: MINI MD Direct current dimmable (TR
- Page 148 and 149: JOLLY HV 25 - 1...10 V & PUSH Direc
- Page 150 and 151: JOLLY PLUS - 1...10 V & PUSH Direct
- Page 152 and 153: JOLLY HV PLUS - 1...10 V & PUSH Dir
- Page 154 and 155: JOLLY US 32 - 1...10 V & PUSH Direc
- Page 156 and 157: JOLLY DALI 32 Direct current dimmab
- Page 158 and 159: JOLLY HC 39 - 1...10 V & PUSH Direc
- Page 160 and 161: PROFESSIONALE DALI 32 Direct curren
- Page 162 and 163: JOLLY MD 32 Direct current dimmable
- Page 164 and 165: WIDESQUARE R - 1...10 V & PUSH Dire
- Page 166 and 167: JOLLY DIN 32 Direct current dimmabl
- Page 168 and 169: MAXI JOLLY SV DALI 40 Direct curren
- Page 170 and 171: MAXI JOLLY US 50 - 1...10 V & PUSH
- Page 172 and 173: MAXI JOLLY US DALI 50 Direct curren
- Page 174 and 175: MAXI JOLLY SV - SELV 60 V - 1...10
- Page 176 and 177: MAXI JOLLY SV DALI - SELV 60 V Dire
- Page 178 and 179: MAXI JOLLY HV 50 - 1...10 V & PUSH
- Page 180 and 181: MAXI JOLLY HV DALI 50 Direct curren
- Page 182 and 183: MAXI JOLLY US TCM 50 - 1...10 V & P
- Page 184 and 185: MAXI JOLLY US DALI TCM 50 Direct cu
- Page 186 and 187: MAXI JOLLY HC 55 - 1...10 V & PUSH
- Page 188 and 189: MAXI JOLLY HC DALI 55 Direct curren
- Page 190 and 191: MAXI JOLLY HC TCM 55 - 1...10 V & P
- Page 192 and 193: MAXI JOLLY HC DALI TCM 55 Direct cu
- Page 194 and 195: MAXI JOLLY H 65 Direct current dimm
JOLLY 25 - 1...10 V & PUSH<br />
Direct current dimmable electronic drivers with DIP-SWITCH<br />
Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH<br />
Made in Europe<br />
professional led applications<br />
05<br />
SELV<br />
RIPPLE<br />
FREE<br />
3.1<br />
Dimmable multipower <strong>LED</strong> drivers<br />
Alimentatori <strong>LED</strong> multipotenza regolabili<br />
Rated Voltage<br />
Tensione Nominale<br />
110 ÷ 120 V (2)<br />
220 ÷ 240 V<br />
Frequency<br />
Frequenza<br />
50...60 Hz<br />
AC Operation range<br />
Tensione di utilizzo AC<br />
99 ÷ 264 V<br />
DC Operation range<br />
Tensione di utilizzo DC<br />
<strong>17</strong>6 ÷ 264 V<br />
(NO PUSH mode<br />
function)<br />
Power<br />
Potenza<br />
0 ÷ 25 W<br />
Maximum current<br />
output ripple<br />
Max. ondulazione<br />
della corrente uscita<br />
≤ 3% (1)<br />
Reference Norms<br />
Norme di riferimento:<br />
EN 50<strong>17</strong>2 (VDE 0108)<br />
EN 55015<br />
EN 61000-3-2<br />
EN 61000-3-3<br />
EN 61347-1<br />
EN 61347-2-13<br />
EN 61547<br />
EN 62384<br />
VDE 0710-T14<br />
Article<br />
Articolo<br />
Code<br />
Codice<br />
P out<br />
W<br />
V out<br />
DC<br />
I out<br />
DC<br />
n° <strong>LED</strong><br />
max. (1)<br />
V out<br />
max.<br />
ta<br />
°C<br />
tc<br />
°C l max. h max.<br />
Power Efficiency (1)<br />
Factor<br />
DC JOLLY 122420 Constant current output - Uscita in corrente costante -25...+50 75 0,98 > 87<br />
15 (15 (2) ) 43 max. 350 mA cost. 12 49<br />
22 (15 (2) ) 43 max. 500 mA cost. 11/12<br />
25 (15 (2) ) 36 max. 700 mA cost. 9<br />
Constant voltage output - Uscita in tensione costante<br />
9 (9 (2) ) 10 cost. 900 mA max. - -<br />
10 (10 (2) ) 12 cost. 900 mA max. - -<br />
20 (15 (2) ) 24 cost. 900 mA max. - -<br />
(1)<br />
Referred to V in<br />
= 230 V, 100% load - Riferito a V in<br />
= 230 V, carico 100%<br />
Features<br />
• Multipower driver supplied with dip-switch for the selection of<br />
the output current.<br />
• IP20 independent driver, for indoor use.<br />
• Class II protection against electric shock for direct or indirect<br />
contact.<br />
• Active Power Factor Corrector.<br />
• Current regulation ±5 % including temperature variations.<br />
• Input and output terminal blocks on the same side (wire<br />
cross-section up to 1,5 mm 2 / AWG15).<br />
• Clamping screws on primary and secondary circuits for cables<br />
with diameter: min. 3 mm - max. 8 mm.<br />
• Protections:<br />
- against overheating and short circuits;<br />
- against mains voltage spikes;<br />
- against overloads.<br />
• Thermal protection = C.5.a.<br />
Accessories not supplied - Accessori non a corredo<br />
Article - Articolo L (length) Code - Codice<br />
1,5 m / 4 ft 485720512<br />
Synchronization cable<br />
4 m / 13 ft 485720513<br />
Cavetto di sincronizzazione 50 cm / 19,68'' 485720515<br />
20 cm / 7,87'' 485720516<br />
REG 1-10 V (pag. 351)<br />
123999L<br />
DCC DALI INTERFACE (pag. 328) 122099<br />
BMU DMX INTERFACE (pag. 330) 122066<br />
Caratteristiche<br />
• Alimentatore multipotenza fornito di dip-switch per la selezione<br />
della corrente in uscita.<br />
• Alimentatore indipendente IP20, per uso interno.<br />
• Protetto in classe II contro le scosse elettriche per contatti diretti<br />
e indiretti.<br />
• PFC attivo.<br />
• Corrente regolata ±5 % incluse variazioni di temperatura.<br />
• Morsetti di entrata e uscita sullo stesso lato<br />
(sezione cavo fino a 1,5 mm 2 / AWG15).<br />
• Serracavo su primario e secondario per cavi di diametro:<br />
min. 3 mm - max. 8 mm.<br />
• Protezioni:<br />
- termica e cortocircuito;<br />
- contro le extra-tensioni di rete;<br />
- contro i sovraccarichi.<br />
• Protezione termica = C.5.a.<br />
112 www.tci.it<br />
<strong>TCI</strong> professional <strong>LED</strong> applications