GUIDE TCI LED DRIVERS 2016-17
MINIJOLED - 1...10 V & PUSH Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications SELV RIPPLE FREE 3.1 Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili Rated Voltage Tensione Nominale 110 ÷ 240 V Frequency Frequenza 50...60 Hz AC Operation range Tensione di utilizzo AC 99 ÷ 264 V DC Operation range Tensione di utilizzo DC 176 ÷ 280 V (NO PUSH mode function) Power Potenza 0 ÷ 10 W Maximum current output ripple Max. ondulazione della corrente uscita ≤ 3% (1) Reference Norms Norme di riferimento: EN 50172 (VDE 0108) EN 55015 EN 60335-1 EN 61000-3-2 EN 61000-3-3 EN 61347-1 EN 61347-2-13 EN 61547 EN 62384 VDE 0710-T14 Article Articolo Code Codice P out W V out DC I out DC V out max. ta °C tc °C l Power Factor h max. Efficiency (1) DC MINIJOLED 127104 2,2 4...27 80 mA cost. 11/28 -25...+50 70 0,90 C (2) >83 2,7 4...27 100 mA cost. 3,3 4...27 120 mA cost. 3,8 4...27 140 mA cost. 4,3 4...27 160 mA cost. 4,9 4...27 180 mA cost. 5,4 4...27 200 mA cost. 6 4...27 220 mA cost. 6,5 4...27 240 mA cost. 7 4...27 260 mA cost. 7,6 4...27 280 mA cost. 8,1 4...27 300 mA cost. 8,7 4...27 320 mA cost. 9,2 4...27 340 mA cost. 9,7 4...27 360 mA cost. 10,3 4...27 380 mA cost. (1) Referred to V in = 230 V, 100% load - Riferito a V in = 230 V, carico 100% (2) Pout > 1 W @110 Vin (2) Pout > 4 W @240 Vin AVAILABLE SOON Features • OLED Multipower driver supplied with dip-switch for the selection of the output current. • IP20 independent driver, for indoor use. • Class II protection against electric shock for direct or indirect contact. • Active Power Factor Corrector. • Current regulation ±5 % including temperature variations. • Input and output terminal blocks on the same side (wire cross-section up to 1,5 mm 2 / AWG15). • Clamping screws on primary and secondary circuits for cables with diameter: min. 3 mm - max. 8 mm. • Protections: - against overheating and short circuits; - against mains voltage spikes; - against overloads. • Thermal protection = C.5.a. Accessories not supplied - Accessori non a corredo Article - Articolo Code - Codice REG 1-10 V (pag. 351) 123999L Caratteristiche • Alimentatore multipotenza per OLED fornito di dip-switch per la selezione della corrente in uscita. • Alimentatore indipendente IP20, per uso interno. • Protetto in classe II contro le scosse elettriche per contatti diretti e indiretti. • PFC attivo. • Corrente regolata ±5 % incluse variazioni di temperatura. • Morsetti di entrata e uscita sullo stesso lato (sezione cavo fino a 1,5 mm 2 / AWG15). • Serracavo su primario e secondario per cavi di diametro: min. 3 mm - max. 8 mm. • Protezioni: - termica e cortocircuito; - contro le extra-tensioni di rete; - contro i sovraccarichi. • Protezione termica = C.5.a. 108 www.tci.it TCI professional LED applications
MINIJOLED - 1...10 V & PUSH Direct current dimmable electronic drivers with DIP-SWITCH Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH Made in Europe professional led applications 108 4,25’’ Ø55 2,17’’ Weight - Peso gr. 108 / 3,50 oz. Pcs - Pezzi 50 27,5 1,08’’ 52 2,05’’ 110,4 4,35’’ 22 0,87’’ 3.1 Wiring diagram - Schema di collegamento (Max. LED distance on page info8 - Massima distanza LED a pagina info8) DIP-SWITCH 4 3 2 JP1 SYNC + SEC _ + 1...10 V _ PUSH N PRI L 1 LED PUSH N L DIP-SWITCH 1...10 V 4 3 2 JP1 + SEC _ + _ PUSH N PRI L 1 SYNC LED 1...10 V N L Dimmable multipower LED drivers Alimentatori LED multipotenza regolabili PUSH diagram - Collegamento PUSH 1...10 V diagram - Collegamento 1...10 V Operation Mode •OLED voltage can be selected: - JP1 ON : OLED voltage 4...10 V; - JP1 OFF: OLED voltage 14...27 V. • Light regulation 0/0,5 - 100 % by means of PUSH function, 1...10 V interface (I=0,35 mA) or 100 Kohm potentiometer. • Light regulation 0/0,5 - 100 % by mains of PUSH function (L mains voltage: 170 Kohm): - a short push to turn on and off; - a longer push to increase or decrease light intensity; - regulation automatically stops at minimum and maximum values; - for another on, regulation or off command, release the push button and give the desired command again. • Maximum length of the cable, from push button to last driver, must be max. 15 m / 49 ft. In case of applications where the cable is longer than 15 m / 49 ft, keep this separate from the 110 - 240 Volt mains cable. • ATTENTION: only use normally open push buttons with no incorporated warning light. • Specific dimming terminal connection with a 1...10 Vdc electronic potentiometer (1…10 V local dimming, double insulation required for external connection). For additional details for regulations see pages info12-14. Modalità di funzionamento • Possibilità di selezionare la tensione di OLED: - JP1 ON : tensione OLED 4...10 V; - JP1 OFF: tensione OLED 14...27 V. • Regolazione della luminosità 0/0,5 - 100 % mediante funzione PUSH, Interfaccia 1...10 V (I=0,35 mA) o potenziometro da 100 Kohm. • Regolazione della luminosità 0/0,5 - 100 % mediante la funzione PUSH (tensione di rete L; 170 Kohm): - una pressione breve per accendere e spegnere; - una pressione prolungata per aumentare o diminuire l’intensità luminosa; - la regolazione si ferma automaticamente ai valori minimi e massimi; - per un nuovo comando accensione, regolazione o spegnimento, rilasciare il pulsante e dare nuovamente il comando desiderato. • La lunghezza massima del cavo, dal pulsante all’ultimo trasformatore, deve essere max. 15 m / 49 ft. In caso di applicazioni dove il cavo superi i 15 m / 49 ft, tenere lo stesso separato dal cavo di rete 110 - 240 Volt. • ATTENZIONE: usare solo pulsanti di tipo normalmente aperto privi di spia luminosa incorporata. • Provvisto di morsetto specifico per la regolazione collegando un potenziometro elettronico 1...10 Vdc (dimmerazione locale 1…10 V, per connessioni esterne all’apparecchio garantire il doppio isolamento). Per ulteriori dettagli sulle regolazioni vedi pagine info12-14. TCI professional LED applications www.tci.it 109
- Page 92 and 93: MP 54 BI Direct current electronic
- Page 94 and 95: MP 55 HC Direct current electronic
- Page 96 and 97: MP 55 / 120 HC Direct current elect
- Page 98 and 99: MP 65 H Direct current electronic d
- Page 100 and 101: MP 65 HTCM Direct current electroni
- Page 102 and 103: SMART 70 Direct current electronic
- Page 104 and 105: SUPERSLIM Direct current electronic
- Page 106 and 107: ATON 30/250-700 Direct current elec
- Page 108 and 109: ATON 30/700-1400 Direct current ele
- Page 110 and 111: MP 32 SLIM Direct current electroni
- Page 112 and 113: MP 60 SLIM Direct current electroni
- Page 114 and 115: SMART 70 HC SLIM Direct current ele
- Page 116 and 117: MP 50/350 SLIM Direct current elect
- Page 118 and 119: MP 80/500 SLIM Direct current elect
- Page 120 and 121: MP 80/500 SLIM LS - LEDset2 Direct
- Page 122 and 123: professional led applications Made
- Page 124 and 125: MICRO JOLLY 6 - 1...10 V & PUSH Dir
- Page 126 and 127: MOONLIGHT 6 Direct current dimmable
- Page 128 and 129: RD57 - 1...10 V & PUSH Direct curre
- Page 130 and 131: MICRO MD professional led applicati
- Page 132 and 133: MINIJOLLY 20 - 1...10 V & PUSH Dire
- Page 134 and 135: MINIJOLLY DALI 20 professional led
- Page 136 and 137: MINIJOLLY LC 20 - 1...10 V & PUSH D
- Page 138 and 139: MINIJOLLY LC DALI 20 Direct current
- Page 140 and 141: MINIJOLLY HV Direct current dimmabl
- Page 144 and 145: MINI MD Direct current dimmable (TR
- Page 146 and 147: JOLLY 25 - 1...10 V & PUSH Direct c
- Page 148 and 149: JOLLY HV 25 - 1...10 V & PUSH Direc
- Page 150 and 151: JOLLY PLUS - 1...10 V & PUSH Direct
- Page 152 and 153: JOLLY HV PLUS - 1...10 V & PUSH Dir
- Page 154 and 155: JOLLY US 32 - 1...10 V & PUSH Direc
- Page 156 and 157: JOLLY DALI 32 Direct current dimmab
- Page 158 and 159: JOLLY HC 39 - 1...10 V & PUSH Direc
- Page 160 and 161: PROFESSIONALE DALI 32 Direct curren
- Page 162 and 163: JOLLY MD 32 Direct current dimmable
- Page 164 and 165: WIDESQUARE R - 1...10 V & PUSH Dire
- Page 166 and 167: JOLLY DIN 32 Direct current dimmabl
- Page 168 and 169: MAXI JOLLY SV DALI 40 Direct curren
- Page 170 and 171: MAXI JOLLY US 50 - 1...10 V & PUSH
- Page 172 and 173: MAXI JOLLY US DALI 50 Direct curren
- Page 174 and 175: MAXI JOLLY SV - SELV 60 V - 1...10
- Page 176 and 177: MAXI JOLLY SV DALI - SELV 60 V Dire
- Page 178 and 179: MAXI JOLLY HV 50 - 1...10 V & PUSH
- Page 180 and 181: MAXI JOLLY HV DALI 50 Direct curren
- Page 182 and 183: MAXI JOLLY US TCM 50 - 1...10 V & P
- Page 184 and 185: MAXI JOLLY US DALI TCM 50 Direct cu
- Page 186 and 187: MAXI JOLLY HC 55 - 1...10 V & PUSH
- Page 188 and 189: MAXI JOLLY HC DALI 55 Direct curren
- Page 190 and 191: MAXI JOLLY HC TCM 55 - 1...10 V & P
MINIJO<strong>LED</strong> - 1...10 V & PUSH<br />
Direct current dimmable electronic drivers with DIP-SWITCH<br />
Alimentatori elettronici regolabili in corrente continua con DIP-SWITCH<br />
Made in Europe<br />
professional led applications<br />
108<br />
4,25’’<br />
Ø55<br />
2,<strong>17</strong>’’<br />
Weight - Peso gr. 108 / 3,50 oz.<br />
Pcs - Pezzi 50<br />
27,5<br />
1,08’’<br />
52<br />
2,05’’<br />
110,4<br />
4,35’’<br />
22<br />
0,87’’<br />
3.1<br />
Wiring diagram - Schema di collegamento (Max. <strong>LED</strong> distance on page info8 - Massima distanza <strong>LED</strong> a pagina info8)<br />
DIP-SWITCH<br />
4 3 2<br />
JP1 SYNC<br />
+<br />
SEC _<br />
+ 1...10 V _<br />
PUSH<br />
N<br />
PRI<br />
L<br />
1<br />
<strong>LED</strong><br />
PUSH<br />
N<br />
L<br />
DIP-SWITCH<br />
1...10 V<br />
4 3 2<br />
JP1<br />
+<br />
SEC _<br />
+ _<br />
PUSH<br />
N<br />
PRI<br />
L<br />
1<br />
SYNC<br />
<strong>LED</strong><br />
1...10 V<br />
N<br />
L<br />
Dimmable multipower <strong>LED</strong> drivers<br />
Alimentatori <strong>LED</strong> multipotenza regolabili<br />
PUSH diagram - Collegamento PUSH<br />
1...10 V diagram - Collegamento 1...10 V<br />
Operation Mode<br />
•O<strong>LED</strong> voltage can be selected:<br />
- JP1 ON : O<strong>LED</strong> voltage 4...10 V;<br />
- JP1 OFF: O<strong>LED</strong> voltage 14...27 V.<br />
• Light regulation 0/0,5 - 100 % by means of PUSH function, 1...10 V interface<br />
(I=0,35 mA) or 100 Kohm potentiometer.<br />
• Light regulation 0/0,5 - 100 % by mains of PUSH function<br />
(L mains voltage: <strong>17</strong>0 Kohm):<br />
- a short push to turn on and off;<br />
- a longer push to increase or decrease light intensity;<br />
- regulation automatically stops at minimum and maximum values;<br />
- for another on, regulation or off command, release the push button and give<br />
the desired command again.<br />
• Maximum length of the cable, from push button to last driver, must be<br />
max. 15 m / 49 ft. In case of applications where the cable is longer than<br />
15 m / 49 ft, keep this separate from the 110 - 240 Volt mains cable.<br />
• ATTENTION: only use normally open push buttons with no incorporated<br />
warning light.<br />
• Specific dimming terminal connection with a 1...10 Vdc electronic<br />
potentiometer (1…10 V local dimming, double insulation required for external<br />
connection).<br />
For additional details for regulations see pages info12-14.<br />
Modalità di funzionamento<br />
• Possibilità di selezionare la tensione di O<strong>LED</strong>:<br />
- JP1 ON : tensione O<strong>LED</strong> 4...10 V;<br />
- JP1 OFF: tensione O<strong>LED</strong> 14...27 V.<br />
• Regolazione della luminosità 0/0,5 - 100 % mediante funzione PUSH,<br />
Interfaccia 1...10 V (I=0,35 mA) o potenziometro da 100 Kohm.<br />
• Regolazione della luminosità 0/0,5 - 100 % mediante la funzione PUSH<br />
(tensione di rete L; <strong>17</strong>0 Kohm):<br />
- una pressione breve per accendere e spegnere;<br />
- una pressione prolungata per aumentare o diminuire l’intensità luminosa;<br />
- la regolazione si ferma automaticamente ai valori minimi e massimi;<br />
- per un nuovo comando accensione, regolazione o spegnimento, rilasciare il<br />
pulsante e dare nuovamente il comando desiderato.<br />
• La lunghezza massima del cavo, dal pulsante all’ultimo trasformatore,<br />
deve essere max. 15 m / 49 ft. In caso di applicazioni dove il cavo superi i<br />
15 m / 49 ft, tenere lo stesso separato dal cavo di rete 110 - 240 Volt.<br />
• ATTENZIONE: usare solo pulsanti di tipo normalmente aperto privi di spia<br />
luminosa incorporata.<br />
• Provvisto di morsetto specifico per la regolazione collegando un<br />
potenziometro elettronico 1...10 Vdc (dimmerazione locale 1…10 V, per<br />
connessioni esterne all’apparecchio garantire il doppio isolamento).<br />
Per ulteriori dettagli sulle regolazioni vedi pagine info12-14.<br />
<strong>TCI</strong> professional <strong>LED</strong> applications www.tci.it<br />
109