caution - Tekno Point

More documents

Recommendations

Info

SealDrain jointThe base pan holeof outdoor unitSeal♦ REFRIGERANT PIPING1. Flaringa) Cut a pipe with a pipe cutterThe b ase panof outdoor unitDrainjoin tFig. 6-3Oblique Roughness Burr90° AFig. 6-4 Fig. 6-5b) Insert a flare nut into a pipe and flare the pipe.Models of indoor Gas pipe Liquid pipe Max height drop between Flare diameter (mm)units diameter diameter indoor and outdoor units (m)Min Max3500 W Ø 3/8" 12 12,4Ø 1/4"5300 W Ø 1/2"1515,4 15,87100 W Ø 5/8" Ø 3/8"18.6 19.02. Connect the indoor unit at first, then the outdoor unit.Bend the tubing in proper way. Do not harm to them.Bend the pipe with thumbmin-radius 100mmFig. 6-6• The bending angle should not exceed 90.• Do not bend the pipe more than three times.• When connecting the flare nut, coat the flare both inside and outside with either oil or ester oil and initially tighten byhand 3 or 4 turns before tightening firmly.Fig. 6-7• Be sure to use both a spanner and torque wrench together when connecting or disconnecting pipes to /from the unit.Fig. 6-856
! CAUTIONToo large torque will harm the bell mouthing and too small will cause leakage. Please determine thetorque according to Table below.After the connecting work is finished, be sure to check that there is no gas leak.Outer diameterTightening torque N.mФ6.4 15 ~ 16 Nm (153 ~ 163 kgf cm)Ф9.5 25 ~ 26 Nm (255 ~ 265 kgf cm)Ф12.7 35 ~ 36 Nm (357 ~ 367 kgf cm)Ф1645 ~ 47 Nm (459 ~ 480 kgf cm)♦ HOW TO EXPEL THE AIR WITH A VACUUM PUMPStop valve operation introductiona) Opening stop valve1. Remove the cap and turn the valve counter clock-wise with the hexagon wrench.2. Turn it until the shaft stops. Do not apply excessive force to the stop valve. Doing so may break the valve body, asthe valve is not a backseat type. Always use the special tool.3. Make sure to tighten the cap securely.b) Closing stop valve1. Remove the cap and turn the valve clockwise with the hexagon wrench.2. Securely tighten the valve until the shaft contacts the main body seal.Make sure to tighten the cap securely. For the tightening torque, refer to the table above.! CAUTIONAlways use a charge hose for service port connection.After tightening the cap, check that no refrigerant leaks are present.service portmaintenance nutcapsealshafthexago n holeFig. 6-9• Using the vacuum pump1. Loosen and remove the maintenance nuts of stop valves A and B, and connect the charge hose of the manifold valveto the service port of stop valve A. (Be sure that stop valves A and B are both closed)2. Connect the joint of the charge hose with the vacuum pump.3. Open the Lo-lever of the manifold value completely.4. Turn on the vacuum pump. At the beginning of pumping, loosen the maintenance nut of stop valve B a little to checkwhether the air comes in (the sound of the pump changes, and the indicator of compound meter turns below zero).Then fasten the maintenance nut.5. When the pumping has finished, close the Lo-lever of the manifold valve completely and turn off the vacuum pump.Make pumping for 15 minutes or more and check that the compound meter indicates -76cmHg (-1X10 Pa).6. Loosen and remove the cap of stop valves A and B to open stop valve A and B completely, then fasten the cap.7. Disassemble the charge hose from the service port of stop valve A, and fasten the nut.In do o rOutdoorunitunit AGas side CLiq uid sideDBStop valveFig. 6-1057
Page 1:
Climatizzatore FREE MATCH CassetteM
Page 4 and 5:
I. INFORMAZIONI IMPORTANTILeggere i
Page 6 and 7: X -FA NCLOCKFANTIMERONH O U RII. DE
Page 8 and 9: ♦ COME INSERIRE/SOSTITUIRE LE BAT
Page 10 and 11: 2) Per confermare l'orario desidera
Page 12 and 13: ♦ TASTI DEL FILOCOMANDOFig. 3: Ta
Page 15 and 16: Accenderel’unitàPremere “Funct
Page 17 and 18: III. 2. CONSIGLI PER IL FUNZIONAMEN
Page 19 and 20: IV. SEZIONE DI INSTALLAZIONEIV. 1.
Page 21 and 22: III. 5. INSTALLAZIONE DELL’UNITÀ
Page 23 and 24: d) Regolare il pannello accuratamen
Page 25 and 26: Se il tubo di scarico e collegato a
Page 27 and 28: ♦ TUBAZIONI REFRIGERANTE1. Svasat
Page 29 and 30: ! CAUTELALa carica refrigerante si
Page 31 and 32: IV. 8. FUNZIONAMENTO DI PROVA• Il
Page 33 and 34: I. IMPORTANT SAFETY INFORMATIONTo p
Page 35 and 36: X -FA NCLOCKFANTIMERONH O U RII. DE
Page 37 and 38: ♦ HOW TO INSERT THE BATTERIESUse
Page 39 and 40: CAUTIONS- When you select the timer
Page 41 and 42: ♦ BUTTONS ON THE WIRED CONTROLLER
Page 43 and 44: Turn on theunit, withoutturning on
Page 45 and 46: ♦ INSTALLATION OF WIRED CONTROLLE
Page 47 and 48: ♦ THE MAINTENANCE OF THE OUTDOOR
Page 49 and 50: TIM E R O NECON OM ICALMTEMPTIMER O
Page 51 and 52: Length = H-181+Lc) Please adjust th
Page 53 and 54: - Wiring between indoor and outdoor
Page 55: IV.6. OUTDOOR UNIT INSTALLATION♦
Page 59 and 60: ♦ CONNECTION OF SIGNAL LINE OF WI
Page 61 and 62: 3. SCHEMI ELETTRICI / WIRING DIAGRA
Page 63: ■ CABLAGGI UNITÀ ESTERNA DC INVE
show all

caution - Tekno Point

Create successful ePaper yourself

Delete template?

Save as template?