MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

More documents

Recommendations

Info

Programmer Operation<strong>2604</strong> ControllerThe above five parameters are repeated for PSP2 and PSP3 if they are configuredSeg DurationDuration for Time to Targetprogrammerd : h : m : sWait Event Wait if selected event is true No waitEvent AEvent BEvent CProg User Val 1 Allows a programmer uservalue to be chosen.Only appears if Prog UserVal 1 is configuredProg User Val 2Allows a programmer uservalue to be chosen.Only appears if Prog UserVal 2 is configuredPID Set Selects a set of PID values PID Set 1toPID Set 3Prog DO ValuesGo Back SegGo Back CyclesSets programmer eventoutputs on or offAllows repeat segments to beset up within a profile. Goback defines the point in theprogram where the repeatsegments are entered.Sets up the number of timesthe segments are repeatedNo Wait0 to 100 0 L10 to 100 0 L11 tonumber ofsegmentsL1. Doesnot appearfor RampRateProgrammeror EndsegmentL1. Onlyshown if waiteventsconfiguredL3. Onlyshown if PIDsetsconfiguredL1. Onlyshown ifDoutconfiguredL1. Onlyshown ifsegment.type is GoBack1 to 999 1 L1. Onlyshown ifsegment.type is GoBack4-20 User Guide Part No HA026491 Issue 3.0 Apr-02
<strong>2604</strong> Controller Programmer Operation4.9. EXAMPLES4.9.1. Program Data Entry Example in a Ramp Rate ProgrammerDo This The Display You Should See Additional Notes1. Select the PROGRAMEDIT (Segment Page)P:PROGRAM EDITvSegment Page2. Press to select EditPrg: 13. Press or to selectthe program to be edited4. Press to selectSegment Number5. Press or to selectsegment (1)6. Press to selectSegment Type7. Press or to selectProfile8. Press to select PSP1Type 19. Press or to selectRamp10. Press to select PSP1TargetEdit Prg: 1Program 1S:Segment Numberv1S:Segment TypevProfileS:PSP1 TypevRampS:PSP1 Targetv40The name of the programmay have beencustomisedIf this is a new program,the message‘Create Prog 1?’ will bedisplayed.Press to confirmSelect:-Profile for a normalsegmentEnd for an end segmentGoBack to repeatsegments in the programSelect:-Ramp to ramp the setpointup or downDwell to dwellStep to jump from thecurrent setpoint to a newtargetThe setpoint will ramp to4011. Press or to setthe setpoint which to rampto12. Press to select PSP1Rate13. Press or to setthe rate at which you wishto ramp to setpointS:PSP1 Ratev1The setpoint will ramp to 40at the rate of 1 unit per sec,min or hour.If PSP1 Type = DwellThis parameter is Dwell TmIf PSP1 Type = StepThis parameter is omittedUser Guide. Part No HA026491 Issue 3.0 Apr-02 4-21
Page 1 and 2:
2604 Controller ContentsMODEL 2604
Page 3 and 4:
RESEARCHLETTERaReference beamHOEabO
Page 5 and 6:
2604 Controller Introduction1.2. BE
Page 9 and 10:
2604 Controller Introduction1.3.2.
Page 11:
2604 Controller Introduction1.5. I/
Page 17 and 18:
2604 Controller InstallationThe thr
Page 19 and 20:
2604 Controller Installation2.3.2.
Page 21 and 22:
Page 23 and 24:
Page 25: 2604 Controller InstallationRS485 4
Page 29 and 30: 2604 Controller InstallationRS485 2
Page 31 and 32: 2604 Controller InstallationI/O Mod
Page 33 and 34: 2604 Controller InstallationI/O Mod
Page 35 and 36: 2604 Controller InstallationTransdu
Page 37 and 38: 2604 Controller Installation2.5.1.
Page 39 and 40: 2604 Controller Operation3. CHAPTER
Page 41 and 42: 2604 Controller Operation3.1. POWER
Page 43 and 44: 2604 Controller Operation3.3. THE A
Page 45 and 46: 2604 Controller Operation3.5.1. To
Page 51 and 52: 2604 Controller Operation3.6.6. Par
Page 53 and 54: 2604 Controller Operation3.7.1. Loo
Page 55 and 56: 2604 Controller Operation3.12. PARA
Page 57 and 58: 2604 Controller Programmer Operatio
Page 75: 2604 Controller Programmer Operatio
Page 85 and 86: 2604 Controller Alarm Operation5. C
Page 87 and 88: 2604 Controller Alarm Operation5.2.
Page 99 and 100: 2604 Controller Appendix AA. APPEND
Page 101 and 102: 2604 Controller Appendix AA.2. CONF
Page 103 and 104: 2604 Controller Safety and EMC Info
Page 109 and 110: 2604 Controller Technical Specifica
show all

MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

Create successful ePaper yourself

Delete template?

Save as template?