MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

More documents

Recommendations

Info

Operation 2604 Controller3-18 User Guide Part No HA026491 Issue 3.0 Apr-02
2604 Controller Programmer Operation4. CHAPTER 4 PROGRAMMER OPERATION ............. 24.1. CUSTOMISABLE PARAMETER NAMES.........................................24.2. WHAT IS SETPOINT PROGRAMMING ? ........................................34.3. SETPOINT PROGRAMMER DEFINITIONS ....................................44.3.1. Run........................................................................................................44.3.2. Hold ......................................................................................................44.3.3. Reset......................................................................................................44.3.4. Servo .....................................................................................................44.3.5. Hot Start................................................................................................44.3.6. Power Fail Recovery.............................................................................44.3.7. Holdback (Guaranteed Soak) ................................................................54.3.8. External Program Inputs........................................................................54.3.9. Wait.......................................................................................................64.4. PROGRAMMER TYPES.......................................................................74.4.1. Time To Target Programmer.................................................................74.4.2. Ramp Rate Programmer ........................................................................74.5. SEGMENT TYPES .................................................................................74.5.1. Profile....................................................................................................74.5.2. Go Back Segment..................................................................................84.5.3. End Segment .........................................................................................84.6. OTHER FEATURES NOT COVERED IN THIS USER GUIDE.......84.7. PROGRAMMER OPERATION............................................................94.7.1. To Run, Hold or Reset a Program.........................................................94.7.2. Run Parameters ...................................................................................104.8. TO CREATE OR EDIT A PROGRAM ..............................................144.8.1. To Define Parameters Common To A Program ..................................154.8.2. PROGRAM EDIT (Program Page) Parameters ..................................164.8.3. To Set Up Each Segment Of A Program.............................................184.8.4. PROGRAM EDIT(Segment Page) Parameters ...................................194.9. EXAMPLES...........................................................................................214.9.1. Program Data Entry Example in a Ramp Rate Programmer ...............214.9.2. Prog Data Entry Example - Time to Target Programmer....................234.9.3. Holdback Example..............................................................................244.9.4. Wait Example......................................................................................254.9.5. Program Names example.....................................................................27User Guide. Part No HA026491 Issue 3.0 Apr-02 4-1
Page 1 and 2:
2604 Controller ContentsMODEL 2604
Page 3 and 4:
RESEARCHLETTERaReference beamHOEabO
Page 5 and 6: 2604 Controller Introduction1.2. BE
Page 9 and 10: 2604 Controller Introduction1.3.2.
Page 11: 2604 Controller Introduction1.5. I/
Page 17 and 18: 2604 Controller InstallationThe thr
Page 19 and 20: 2604 Controller Installation2.3.2.
Page 25: 2604 Controller InstallationRS485 4
Page 29 and 30: 2604 Controller InstallationRS485 2
Page 31 and 32: 2604 Controller InstallationI/O Mod
Page 33 and 34: 2604 Controller InstallationI/O Mod
Page 35 and 36: 2604 Controller InstallationTransdu
Page 39 and 40: 2604 Controller Operation3. CHAPTER
Page 41 and 42: 2604 Controller Operation3.1. POWER
Page 43 and 44: 2604 Controller Operation3.3. THE A
Page 45 and 46: 2604 Controller Operation3.5.1. To
Page 51 and 52: 2604 Controller Operation3.6.6. Par
Page 53 and 54: 2604 Controller Operation3.7.1. Loo
Page 55: 2604 Controller Operation3.12. PARA
Page 59 and 60: 2604 Controller Programmer Operatio
Page 85 and 86: 2604 Controller Alarm Operation5. C
Page 87 and 88: 2604 Controller Alarm Operation5.2.
Page 99 and 100: 2604 Controller Appendix AA. APPEND
Page 101 and 102: 2604 Controller Appendix AA.2. CONF
Page 103 and 104: 2604 Controller Safety and EMC Info
Page 105 and 106: 2604 Controller Safety and EMC Info
Page 107 and 108:
2604 Controller Safety and EMC Info
Page 109 and 110:
2604 Controller Technical Specifica
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
show all

MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

Create successful ePaper yourself

Delete template?

Save as template?