MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

More documents

Recommendations

Info

Installation<strong>2604</strong> Controller2.5. TO CONNECT ZIRCONIA (DUAL SIGNAL) PROBEA dual signal probe, such as a Zirconia probe, will normally be connected to a Dual PV Inputmodule (Code DP). The module presents two channels, A and C, where A is the voltage inputand C is the mV, thermocouple, RTD or mA input.Example 1 shown below uses the Dual PV Input module with both channels configured. Inthis configuration the module runs at 4.5Hz. The two channels are un-isolated from oneanotherbut isolated from the rest of the instrument.Example 2 uses two modules. The modules can either be two PV Input modules (code PV) ora Dual PV Input module (code DP) with Channel C configured as ‘None’ plus a PV Inputmodule. This combination runs at 9Hz and may be used if the loop is unusually fast.I/O ModuleDual PVInputTypicalusageZirconiaprobeOrderCodeDPConnections and examples of useExample 1:- Using the Dual PV Input Module.Channel C is shown configured for thermocouple.The temperature sensor of a zirconia probe isconnected to this input, terminals C & D. TheVolt Source is connected to the A channel,terminals A & D.-ZirconiaVoltsource ++-Note: The +ve of the voltsource must be connected tothe-ve of the thermocouple.ABCDTwo PVInputModulesPVExample 2:- Using Two ModulesThe temperature sensor of the zirconia probe canbe connected to the precision PV input of one I/Omodule, connections C & D, with the Volt Sourceconnected to the second module, terminals A &D.+AZirconiaBVolt+sourceC-C-DDFigure 2-19: Wiring Connections for Zirconia Probe2-24 User Guide Part No HA026491 Issue 3.0 Apr-02
<strong>2604</strong> Controller Installation2.5.1. Zirconia Probe Screening2.5.1.1. Zirconia Carbon Probe ConstructionHot EndZirconiaSensorOuter ElectrodeCeramic InsulatorInner ElectrodeOuter metallic shell of the probeScreen-Zirc. mV++Thermocouple-2.5.1.2. Screening connections when two modules are usedThe zirconia sensor wires should be screened and connected to the outer shell of the probe if itis situated in an area of high interference.A+BOuter ElectrodeInner ElectrodeScreenZirc. mV+-+Screened Cable-CDAT.C.-+BC-D2.5.1.3. Screening connections when a dual input module is usedBoth the thermocouple and the zirconia sensor wires must be screened and connected to theouter shell of the probe if it is situated in an area of high interference.Note the reverse connection of the zirconia sensor .Outer ElectrodeInner ElectrodeScreenZirc. mVT.C.+--+Screened CableScreened Compensating Cable-++-ABCDUser Guide Part No HA026491 Issue 3.0 Apr-02 2-25
Page 1 and 2: 2604 Controller ContentsMODEL 2604
Page 3 and 4: RESEARCHLETTERaReference beamHOEabO
Page 5 and 6: 2604 Controller Introduction1.2. BE
Page 9 and 10: 2604 Controller Introduction1.3.2.
Page 11: 2604 Controller Introduction1.5. I/
Page 17 and 18: 2604 Controller InstallationThe thr
Page 19 and 20: 2604 Controller Installation2.3.2.
Page 25: 2604 Controller InstallationRS485 4
Page 29 and 30: 2604 Controller InstallationRS485 2
Page 31 and 32: 2604 Controller InstallationI/O Mod
Page 33 and 34: 2604 Controller InstallationI/O Mod
Page 35: 2604 Controller InstallationTransdu
Page 39 and 40: 2604 Controller Operation3. CHAPTER
Page 41 and 42: 2604 Controller Operation3.1. POWER
Page 43 and 44: 2604 Controller Operation3.3. THE A
Page 45 and 46: 2604 Controller Operation3.5.1. To
Page 51 and 52: 2604 Controller Operation3.6.6. Par
Page 53 and 54: 2604 Controller Operation3.7.1. Loo
Page 55 and 56: 2604 Controller Operation3.12. PARA
Page 57 and 58: 2604 Controller Programmer Operatio
Page 85 and 86: 2604 Controller Alarm Operation5. C
Page 87 and 88:
2604 Controller Alarm Operation5.2.
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
2604 Controller Appendix AA. APPEND
Page 101 and 102:
2604 Controller Appendix AA.2. CONF
Page 103 and 104:
2604 Controller Safety and EMC Info
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
2604 Controller Technical Specifica
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
show all

MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

Create successful ePaper yourself

Delete template?

Save as template?