MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k
MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k
Installation2604 Controller2.5. TO CONNECT ZIRCONIA (DUAL SIGNAL) PROBEA dual signal probe, such as a Zirconia probe, will normally be connected to a Dual PV Inputmodule (Code DP). The module presents two channels, A and C, where A is the voltage inputand C is the mV, thermocouple, RTD or mA input.Example 1 shown below uses the Dual PV Input module with both channels configured. Inthis configuration the module runs at 4.5Hz. The two channels are un-isolated from oneanotherbut isolated from the rest of the instrument.Example 2 uses two modules. The modules can either be two PV Input modules (code PV) ora Dual PV Input module (code DP) with Channel C configured as ‘None’ plus a PV Inputmodule. This combination runs at 9Hz and may be used if the loop is unusually fast.I/O ModuleDual PVInputTypicalusageZirconiaprobeOrderCodeDPConnections and examples of useExample 1:- Using the Dual PV Input Module.Channel C is shown configured for thermocouple.The temperature sensor of a zirconia probe isconnected to this input, terminals C & D. TheVolt Source is connected to the A channel,terminals A & D.-ZirconiaVoltsource ++-Note: The +ve of the voltsource must be connected tothe-ve of the thermocouple.ABCDTwo PVInputModulesPVExample 2:- Using Two ModulesThe temperature sensor of the zirconia probe canbe connected to the precision PV input of one I/Omodule, connections C & D, with the Volt Sourceconnected to the second module, terminals A &D.+AZirconiaBVolt+sourceC-C-DDFigure 2-19: Wiring Connections for Zirconia Probe2-24 User Guide Part No HA026491 Issue 3.0 Apr-02
2604 Controller Installation2.5.1. Zirconia Probe Screening2.5.1.1. Zirconia Carbon Probe ConstructionHot EndZirconiaSensorOuter ElectrodeCeramic InsulatorInner ElectrodeOuter metallic shell of the probeScreen-Zirc. mV++Thermocouple-2.5.1.2. Screening connections when two modules are usedThe zirconia sensor wires should be screened and connected to the outer shell of the probe if itis situated in an area of high interference.A+BOuter ElectrodeInner ElectrodeScreenZirc. mV+-+Screened Cable-CDAT.C.-+BC-D2.5.1.3. Screening connections when a dual input module is usedBoth the thermocouple and the zirconia sensor wires must be screened and connected to theouter shell of the probe if it is situated in an area of high interference.Note the reverse connection of the zirconia sensor .Outer ElectrodeInner ElectrodeScreenZirc. mVT.C.+--+Screened CableScreened Compensating Cable-++-ABCDUser Guide Part No HA026491 Issue 3.0 Apr-02 2-25
- Page 1 and 2: 2604 Controller ContentsMODEL 2604
- Page 3 and 4: RESEARCHLETTERaReference beamHOEabO
- Page 5 and 6: 2604 Controller Introduction1.2. BE
- Page 9 and 10: 2604 Controller Introduction1.3.2.
- Page 11: 2604 Controller Introduction1.5. I/
- Page 17 and 18: 2604 Controller InstallationThe thr
- Page 19 and 20: 2604 Controller Installation2.3.2.
- Page 21 and 22: 2604 Controller Installation2.3.4.
- Page 23 and 24: 2604 Controller Installation2.3.6.
- Page 25: 2604 Controller InstallationRS485 4
- Page 29 and 30: 2604 Controller InstallationRS485 2
- Page 31 and 32: 2604 Controller InstallationI/O Mod
- Page 33 and 34: 2604 Controller InstallationI/O Mod
- Page 35: 2604 Controller InstallationTransdu
- Page 39 and 40: 2604 Controller Operation3. CHAPTER
- Page 41 and 42: 2604 Controller Operation3.1. POWER
- Page 43 and 44: 2604 Controller Operation3.3. THE A
- Page 45 and 46: 2604 Controller Operation3.5.1. To
- Page 47 and 48: 2604 Controller Operation3.6.2. To
- Page 49 and 50: 2604 Controller Operation3.6.5. To
- Page 51 and 52: 2604 Controller Operation3.6.6. Par
- Page 53 and 54: 2604 Controller Operation3.7.1. Loo
- Page 55 and 56: 2604 Controller Operation3.12. PARA
- Page 57 and 58: 2604 Controller Programmer Operatio
- Page 59 and 60: 2604 Controller Programmer Operatio
- Page 61 and 62: 2604 Controller Programmer Operatio
- Page 63 and 64: 2604 Controller Programmer Operatio
- Page 65 and 66: 2604 Controller Programmer Operatio
- Page 67 and 68: 2604 Controller Programmer Operatio
- Page 69 and 70: 2604 Controller Programmer Operatio
- Page 71 and 72: 2604 Controller Programmer Operatio
- Page 73 and 74: 2604 Controller Programmer Operatio
- Page 75 and 76: 2604 Controller Programmer Operatio
- Page 77 and 78: 2604 Controller Programmer Operatio
- Page 79 and 80: 2604 Controller Programmer Operatio
- Page 81 and 82: 2604 Controller Programmer Operatio
- Page 83 and 84: 2604 Controller Programmer Operatio
- Page 85 and 86: 2604 Controller Alarm Operation5. C
Installation<strong>2604</strong> Controller2.5. TO CONNECT ZIRCONIA (DUAL SIGNAL) PROBEA dual signal probe, such as a Zirconia probe, will normally be connected to a Dual PV Inputmodule (Code DP). The module presents two channels, A and C, where A is the voltage inputand C is the mV, thermocouple, RTD or mA input.Example 1 shown below uses the Dual PV Input module with both channels configured. Inthis configuration the module runs at 4.5Hz. The two channels are un-isolated from oneanotherbut isolated from the rest of the instrument.Example 2 uses two modules. The modules can either be two PV Input modules (code PV) ora Dual PV Input module (code DP) with Channel C configured as ‘None’ plus a PV Inputmodule. This combination runs at 9Hz and may be used if the loop is unusually fast.I/O ModuleDual PVInputTypicalusageZirconiaprobeOrderCodeDPConnections and examples of useExample 1:- Using the Dual PV Input Module.Channel C is shown configured for thermocouple.The temperature sensor of a zirconia probe isconnected to this input, terminals C & D. TheVolt Source is connected to the A channel,terminals A & D.-ZirconiaVoltsource ++-Note: The +ve of the voltsource must be connected tothe-ve of the thermocouple.ABCDTwo PVInputModulesPVExample 2:- Using Two ModulesThe temperature sensor of the zirconia probe canbe connected to the precision PV input of one I/Omodule, connections C & D, with the Volt Sourceconnected to the second module, terminals A &D.+AZirconiaBVolt+sourceC-C-DDFigure 2-19: Wiring Connections for Zirconia Probe2-24 User Guide Part No HA026491 Issue 3.0 Apr-02