MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k
MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k
2604 Controller Installation2.1.3. Mounting the Controller1. Prepare the panel cut-out to the size shown in Figure 2-2. Ensure that there is sufficientspacing between instruments as shown by the minimum dimensions given in Figure 2-2.Ensure also that the controller is not mounted close to any device which is likely toproduce a significant amount of heat which may affect the performance of the controller.2. Insert the controller through the panel cut-out.3. Spring the upper and lower panel retaining clips into place. Secure the controller inposition by holding it level and pushing both retaining clips forward.Note:- If the retaining clips subsequently need removing, in order to extract the controllerfrom the control panel, they can be unhooked from the side with either your fingers or ascrewdriver.Panel cut-out92 x 92 mm3.62 x 3.62 in-0+0.8-0+0.03Recommendedminimumspacing ofcontrollers10mm(0.4in)38mm(1.5in)(Not toscale)Figure 2-2: Panel Cut-out and Minimum Spacing Requirements2.1.4. Unplugging and Plugging in the ControllerIf required, the controller can be unplugged from its sleeve by easing the latching earsoutwards and pulling the controller forward out of the sleeve. When plugging the controllerback into its sleeve, ensure that the latching ears click into place.It is recommended that the power to the controller is switched off when un-plugging orplugging the controller into its sleeve. This is to prevent premature wear on the controllerconnectors when current is flowing through them.User Guide Part No HA026491 Issue 3.0 Apr-02 2-3
- Page 1 and 2: 2604 Controller ContentsMODEL 2604
- Page 3 and 4: RESEARCHLETTERaReference beamHOEabO
- Page 5 and 6: 2604 Controller Introduction1.2. BE
- Page 9 and 10: 2604 Controller Introduction1.3.2.
- Page 11: 2604 Controller Introduction1.5. I/
- Page 18 and 19: Installation2604 Controller2.3. STA
- Page 20 and 21: Installation2604 Controller2.3.3. S
- Page 22 and 23: Installation2604 Controller2.3.5. I
- Page 24 and 25: Installation2604 Controller2.4. OPT
- Page 28 and 29: Installation2604 Controller2.4.3. M
- Page 30 and 31: Installation2604 Controller2.4.4. I
- Page 32 and 33: Installation2604 ControllerI/O Modu
- Page 34 and 35: Installation2604 ControllerI/O Modu
- Page 36 and 37: Installation2604 Controller2.5. TO
- Page 38 and 39: Installation2604 Controller2-26 Use
- Page 40 and 41: Operation 2604 Controller3. Chapter
- Page 42 and 43: Operation 2604 Controller3.2. THE O
- Page 44 and 45: Operation 2604 Controller3.5. THE L
- Page 46 and 47: Operation 2604 Controller3.6. PARAM
- Page 48 and 49: Operation 2604 Controller3.6.4. To
- Page 50 and 51: Operation 2604 Controller5. Text (U
- Page 52 and 53: Operation 2604 Controller3.7. SPECI
- Page 54 and 55: Operation 2604 Controller3.8. BACKP
- Page 56 and 57: Operation 2604 Controller3-18 User
- Page 58 and 59: Programmer Operation2604 Controller
- Page 60 and 61: Programmer Operation2604 Controller
<strong>2604</strong> Controller Installation2.1.3. Mounting the Controller1. Prepare the panel cut-out to the size shown in Figure 2-2. Ensure that there is sufficientspacing between instruments as shown by the minimum dimensions given in Figure 2-2.Ensure also that the controller is not mounted close to any device which is likely toproduce a significant amount of heat which may affect the performance of the controller.2. Insert the controller through the panel cut-out.3. Spring the upper and lower panel retaining clips into place. Secure the controller inposition by holding it level and pushing both retaining clips forward.Note:- If the retaining clips subsequently need removing, in order to extract the controllerfrom the control panel, they can be unhooked from the side with either your fingers or ascrewdriver.Panel cut-out92 x 92 mm3.62 x 3.62 in-0+0.8-0+0.03Recommendedminimumspacing ofcontrollers10mm(0.4in)38mm(1.5in)(Not toscale)Figure 2-2: Panel Cut-out and Minimum Spacing Requirements2.1.4. Unplugging and Plugging in the ControllerIf required, the controller can be unplugged from its sleeve by easing the latching earsoutwards and pulling the controller forward out of the sleeve. When plugging the controllerback into its sleeve, ensure that the latching ears click into place.It is recommended that the power to the controller is switched off when un-plugging orplugging the controller into its sleeve. This is to prevent premature wear on the controllerconnectors when current is flowing through them.User Guide Part No HA026491 Issue 3.0 Apr-02 2-3