MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

More documents

Recommendations

Info

Technical Specification<strong>2604</strong> ControllerC.4.ANALOGUE INPUTNo of inputs One fixed (Not isolated)Can be used with either floating or ground referenced transducers oflow impedance.Input range -10V to +10V linear or 0 -20 mA with burden resistor of 100W.Calibration: ±(1.5mV + 0.1% of reading)Resolution: 0.9mVDrift: < ±(0.1mV + 0.006% of reading) per °CInput Impedance: 0.46MΩ (floating input), 0.23MΩ (groundreferenced input)IsolationNot isolated from standard digital I/O . Differential type input withcommon mode range of + 42Vdc (the average voltage of the two inputswith respect to ‘Screen’ or ‘Common’ terminals should be within+42Vdc.CMRR : >110dB at 50/60Hz, >80dB at DCFunctionsProcess variable, remote setpoint, power limit, feedforward, etc.C.5.ANALOGUE INPUT MODULEAllocation Up to 4 analogue input modules can be fitted in I/O slots 1,3,4 & 6mV input100mV range - used for thermocouple, linear mV source, or 0-20mAwith 2.49Ω external burden resistor.Calibration: + 10µV + 0.2% of readingResolution: 6µVDrift: < + 0.2µV + 0.004% of reading per O CInput impedance: >10MΩ, Leakage: 10MΩ, Leakage: 69KΩPt100 input 0 to 400ohms (-200°C to +850°C), 3 matched wires - up to 22W ineach lead without errors.Calibration: ±(0.4°C + 0.15% of reading in °C)Resolution: 0.08°CDrift: < ±(0.015°C + 0.005% of reading in °C) per °CBulb current: 0.3mA.Thermocouple Internal compensation: CJC rejection ratio >25:1 typical.CJ Temperature calibration error at 25 O C:
<strong>2604</strong> Controller Technical SpecificationC.6.Allocationnot isolatedDigital inputsDigital outputsSTANDARD DIGITAL I/O1 digital input standard and 7 I/O which can be configured as inputs oroutputs plus 1 changeover relayVoltage level : input active < 2Vdc, inactive >4VdcContact closure : input active 28kohmsOpen collector, 24Vdc at 40mA drive capability, requires externalsupplyContact rating 2A at 264Vac resistiveChangeover relayFunctions Refer to Chapter 17Operations 1,000,000 operations with addition of external snubberC.7.DIGITAL INPUT MODULESModule type Triple contact input, Triple logic inputAllocation Can be fitted into slots 1, 3, 4, 5 or 6Contact closure Active 28kohmsLogic inputs Current sinking : active 10.8Vdc to 30Vdc at 2.5mAinactive -3 to 5Vdc at
Page 1 and 2:
2604 Controller ContentsMODEL 2604
Page 3 and 4:
RESEARCHLETTERaReference beamHOEabO
Page 5 and 6:
2604 Controller Introduction1.2. BE
Page 9 and 10:
2604 Controller Introduction1.3.2.
Page 11:
2604 Controller Introduction1.5. I/
Page 17 and 18:
2604 Controller InstallationThe thr
Page 19 and 20:
2604 Controller Installation2.3.2.
Page 21 and 22:
Page 23 and 24:
Page 25:
2604 Controller InstallationRS485 4
Page 29 and 30:
2604 Controller InstallationRS485 2
Page 31 and 32:
2604 Controller InstallationI/O Mod
Page 33 and 34:
2604 Controller InstallationI/O Mod
Page 35 and 36:
2604 Controller InstallationTransdu
Page 37 and 38:
Page 39 and 40:
2604 Controller Operation3. CHAPTER
Page 41 and 42:
2604 Controller Operation3.1. POWER
Page 43 and 44:
2604 Controller Operation3.3. THE A
Page 45 and 46:
2604 Controller Operation3.5.1. To
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
2604 Controller Operation3.6.6. Par
Page 53 and 54:
2604 Controller Operation3.7.1. Loo
Page 55 and 56:
2604 Controller Operation3.12. PARA
Page 57 and 58:
2604 Controller Programmer Operatio
Page 59 and 60:
2604 Controller Programmer Operatio
Page 61 and 62: 2604 Controller Programmer Operatio
Page 85 and 86: 2604 Controller Alarm Operation5. C
Page 87 and 88: 2604 Controller Alarm Operation5.2.
Page 99 and 100: 2604 Controller Appendix AA. APPEND
Page 101 and 102: 2604 Controller Appendix AA.2. CONF
Page 103 and 104: 2604 Controller Safety and EMC Info
Page 109 and 110: 2604 Controller Technical Specifica
Page 111: 2604 Controller Technical Specifica
show all

MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?