MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

More documents

Recommendations

Info

Technical Specification<strong>2604</strong> ControllerC. Appendix C Technical SpecificationAll figures quoted at 0 to 50 o C unless otherwise stated.C.1.Sample rateInput filteringUser calibrationSensor breakThermocoupletypesGeneralALL ANALOGUE, DUAL AND PV INPUTS9Hz (110msec.)OFF to 999.9 seconds of filter time constant (f.t.c.). Default setting is0.4 seconds unless stated otherwiseBoth the user calibration and a transducer scaling can be applied.a.c. sensor break on each input (i.e. fast responding and no dc errorswith high impedance sources).Most linearisations including K,J,T,R,B,S,N,L,PII,C,D,E withlinearisation error < ±0.2°CResolution (noise free) is quoted as a typical figure with f.t.c. set to thedefault value = 0.4 second.Resolution generally improves by a factor of two with everyquadrupling of f.t.c.Calibration is quoted as offset error + percentage error of absolutereading at ambient temperature of 25 O CDrift is quoted as extra offset and absolute reading errors per degree ofambient change from 25 O C.C-2 User Guide. Part No HA026491 Issue 3.0 Apr-02
<strong>2604</strong> Controller Technical SpecificationC.2.Allocation(isolated)mV inputPRECISION PV INPUT / MODULEOne standard and up to two additional PV input modules can be fittedin I/O slots 3 and 6Two ranges: ±40mV & ±80mV, used for thermocouple, linear mVsource or 0 - 20mA with 2.49WCalibration: ±(1.5µV + 0.05% of reading), Resolution: 0.5µV for40mV range & 1µV for 80mV rangeDrift: 100MW, Leakage: < 1nA0 - 2V input -1.4V to +2V, used for zirconiaCalibration: ±(0.5mV + 0.05% of reading)Resolution: 60µVDrift: < ±(0.05mV + 0.003% of reading) per °CInput impedance: >100MW, Leakage: < 1nA0 - 10V input -3V to +10V, used for voltage inputCalibration: ±(0.5mV + 0.1% of reading)Resolution: 180µVDrift: 40:1 typical.CJ Temperature calibration error at 25 O C:
Page 1 and 2:
2604 Controller ContentsMODEL 2604
Page 3 and 4:
RESEARCHLETTERaReference beamHOEabO
Page 5 and 6:
2604 Controller Introduction1.2. BE
Page 9 and 10:
2604 Controller Introduction1.3.2.
Page 11:
2604 Controller Introduction1.5. I/
Page 17 and 18:
2604 Controller InstallationThe thr
Page 19 and 20:
2604 Controller Installation2.3.2.
Page 21 and 22:
Page 23 and 24:
Page 25:
2604 Controller InstallationRS485 4
Page 29 and 30:
2604 Controller InstallationRS485 2
Page 31 and 32:
2604 Controller InstallationI/O Mod
Page 33 and 34:
2604 Controller InstallationI/O Mod
Page 35 and 36:
2604 Controller InstallationTransdu
Page 37 and 38:
Page 39 and 40:
2604 Controller Operation3. CHAPTER
Page 41 and 42:
2604 Controller Operation3.1. POWER
Page 43 and 44:
2604 Controller Operation3.3. THE A
Page 45 and 46:
2604 Controller Operation3.5.1. To
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
2604 Controller Operation3.6.6. Par
Page 53 and 54:
2604 Controller Operation3.7.1. Loo
Page 55 and 56:
2604 Controller Operation3.12. PARA
Page 57 and 58:
2604 Controller Programmer Operatio
Page 59 and 60: 2604 Controller Programmer Operatio
Page 85 and 86: 2604 Controller Alarm Operation5. C
Page 87 and 88: 2604 Controller Alarm Operation5.2.
Page 99 and 100: 2604 Controller Appendix AA. APPEND
Page 101 and 102: 2604 Controller Appendix AA.2. CONF
Page 103 and 104: 2604 Controller Safety and EMC Info
Page 109: 2604 Controller Technical Specifica
Page 113 and 114: 2604 Controller Technical Specifica
show all

MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?