MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

More documents

Recommendations

Info

Safety and EMC Information<strong>2604</strong> Controller+AnalogueInputDigital InputCommonVoltageControlVoltageScreen-220K220K100R FuseResistor2.5VInstrument Ground2MW BleedResistorDigital IOComNLFigure B-1: Analogue Input and Fixed Digital I/O Equivalent CircuitB.3.5. WiringIt is important to connect the controller in accordance with the wiring data given in thishandbook. Take particular care not to connect AC supplies to the low voltage sensor input orother low level inputs and outputs. Only use copper conductors for connections (exceptthermocouple inputs) and ensure that the wiring of installations comply with all local wiringregulations. For example in the in the UK use the latest version of the IEE wiring regulations,(BS7671). In the USA use NEC Class 1 wiring methods.B.3.6. Power IsolationThe installation must include a power isolating switch or circuit breaker. This device shouldbe in close proximity to the controller, within easy reach of the operator and marked as thedisconnecting device for the instrument.B.3.7. Earth leakage currentDue to RFI Filtering there is an earth leakage current of less than 0.5mA. This may affect thedesign of an installation of multiple controllers protected by Residual Current Device, (RCD)or Ground Fault Detector, (GFD) type circuit breakers.B-4 User Guide. Part No HA026491 Issue 3.0 Apr-02
<strong>2604</strong> Controller Safety and EMC InformationB.3.8. Overcurrent protectionTo protect the internal PCB tracking within the controller against excess currents, the ACpower supply to the controller and power outputs must be wired through the fuse or circuitbreaker specified in the technical specification.B.3.9. Voltage ratingThe maximum continuous voltage applied between any of the following terminals must notexceed 264Vac:• line or neutral to any other connection;• relay or triac output to logic, dc or sensor connections;• any connection to ground.The controller should not be wired to a three phase supply with an unearthed star connection.Under fault conditions such a supply could rise above 264Vac with respect to ground and theproduct would not be safe.Voltage transients across the power supply connections, and between the power supply andground, must not exceed 2.5kV. Where occasional voltage transients over 2.5kV are expectedor measured, the power installation to both the instrument supply and load circuits shouldinclude a transient limiting device.These units will typically include gas discharge tubes and metal oxide varistors that limit andcontrol voltage transients on the supply line due to lightning strikes or inductive loadswitching. Devices are available in a range of energy ratings and should be selected to suitconditions at the installation.B.3.10. Conductive pollutionElectrically conductive pollution must be excluded from the cabinet in which the controller ismounted. For example, carbon dust is a form of electrically conductive pollution. To secure asuitable atmosphere in conditions of conductive pollution, fit an air filter to the air intake ofthe cabinet. Where condensation is likely, for example at low temperatures, include athermostatically controlled heater in the cabinet.User Guide. Part No HA026491 Issue 3.0 Apr-02 B-5
Page 1 and 2:
2604 Controller ContentsMODEL 2604
Page 3 and 4:
RESEARCHLETTERaReference beamHOEabO
Page 5 and 6:
2604 Controller Introduction1.2. BE
Page 9 and 10:
2604 Controller Introduction1.3.2.
Page 11:
2604 Controller Introduction1.5. I/
Page 17 and 18:
2604 Controller InstallationThe thr
Page 19 and 20:
2604 Controller Installation2.3.2.
Page 21 and 22:
Page 23 and 24:
Page 25:
2604 Controller InstallationRS485 4
Page 29 and 30:
2604 Controller InstallationRS485 2
Page 31 and 32:
2604 Controller InstallationI/O Mod
Page 33 and 34:
2604 Controller InstallationI/O Mod
Page 35 and 36:
2604 Controller InstallationTransdu
Page 37 and 38:
Page 39 and 40:
2604 Controller Operation3. CHAPTER
Page 41 and 42:
2604 Controller Operation3.1. POWER
Page 43 and 44:
2604 Controller Operation3.3. THE A
Page 45 and 46:
2604 Controller Operation3.5.1. To
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
2604 Controller Operation3.6.6. Par
Page 53 and 54:
2604 Controller Operation3.7.1. Loo
Page 55 and 56: 2604 Controller Operation3.12. PARA
Page 57 and 58: 2604 Controller Programmer Operatio
Page 85 and 86: 2604 Controller Alarm Operation5. C
Page 87 and 88: 2604 Controller Alarm Operation5.2.
Page 99 and 100: 2604 Controller Appendix AA. APPEND
Page 101 and 102: 2604 Controller Appendix AA.2. CONF
Page 103 and 104: 2604 Controller Safety and EMC Info
Page 105: 2604 Controller Safety and EMC Info
Page 109 and 110: 2604 Controller Technical Specifica
show all

MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

Create successful ePaper yourself

Delete template?

Save as template?