MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

More documents

Recommendations

Info

Appendix A<strong>2604</strong> ControllerGeneral Notes1. Loop 1 PV defaults to main input on microboard. Loop 2 and 3 PV inputs must be fittedin I/O slots 3 or 6 or be assigned to the analogue input.2. This alarm configuration refers to loop alarms only. One selection per loop is allowed.Additional alarms are available for the user to configure.3. Thermocouple and RTD inputs assume sensor min and max values with no decimal point.4. Linear inputs are ranged 0-100%, no decimal point.5. Temperature inputs will be C unless ordered by USA where F will be supplied.6. Remote setpoints assume loop min & max ranges.7. VP1 or VP2 not available with override function.8. For cascade and override inputs only.9. HR module should be used in feedback mode.A.3. QUICK START CODE EXAMPLE:SVP1/SPID/SPID/K/Z/A/S1A/1VH/2PV/2HV/3HC/3PVThis code configures the hardware specified on page A2 to be:Loop1: Valve position control, Type K input, Ch1 VP output in slot 1, 4-20mA remotesetpoint input.Loop 2: PID control, RTD input in slot 3, 0-10Vdc Ch1 output in slot 4.Loop 3: PID control, 4-20mA input in slot 6, Logic Ch1/Ch2 output in slot 5.A-4 User Guide. Part No HA026491 Issue 3.0 Apr-02
<strong>2604</strong> Controller Safety and EMC InformationB. APPENDIX B SAFETY AND EMC INFORMATION ........... 2B.1. SAFETY .......................................................................................................2B.1.1. Electromagnetic compatibility....................................................................2B.2. SERVICE AND REPAIR............................................................................2B.2.1. Electrostatic discharge precautions.............................................................2B.2.2. Cleaning......................................................................................................2B.3. INSTALLATION SAFETY REQUIREMENTS.......................................3B.3.1. Safety Symbols ...........................................................................................3B.3.2. Personnel ....................................................................................................3B.3.3. Enclosure of live parts ................................................................................3B.3.4. Isolation......................................................................................................3B.3.5. Wiring.........................................................................................................4B.3.6. Power Isolation...........................................................................................4B.3.7. Earth leakage current ..................................................................................4B.3.8. Overcurrent protection................................................................................5B.3.9. Voltage rating .............................................................................................5B.3.10. Conductive pollution ................................................................................5B.3.11. Over-temperature protection.....................................................................6B.3.12. Grounding of the temperature sensor shield .............................................6B.4. INSTALLATION REQUIREMENTS FOR EMC ...................................6B.4.1. Routing of wires .........................................................................................6User Guide. Part No HA026491 Issue 3.0 Apr-02 B-1
Page 1 and 2:
2604 Controller ContentsMODEL 2604
Page 3 and 4:
RESEARCHLETTERaReference beamHOEabO
Page 5 and 6:
2604 Controller Introduction1.2. BE
Page 9 and 10:
2604 Controller Introduction1.3.2.
Page 11:
2604 Controller Introduction1.5. I/
Page 17 and 18:
2604 Controller InstallationThe thr
Page 19 and 20:
2604 Controller Installation2.3.2.
Page 21 and 22:
Page 23 and 24:
Page 25:
2604 Controller InstallationRS485 4
Page 29 and 30:
2604 Controller InstallationRS485 2
Page 31 and 32:
2604 Controller InstallationI/O Mod
Page 33 and 34:
2604 Controller InstallationI/O Mod
Page 35 and 36:
2604 Controller InstallationTransdu
Page 37 and 38:
Page 39 and 40:
2604 Controller Operation3. CHAPTER
Page 41 and 42:
2604 Controller Operation3.1. POWER
Page 43 and 44:
2604 Controller Operation3.3. THE A
Page 45 and 46:
2604 Controller Operation3.5.1. To
Page 47 and 48:
Page 49 and 50:
Page 51 and 52: 2604 Controller Operation3.6.6. Par
Page 53 and 54: 2604 Controller Operation3.7.1. Loo
Page 55 and 56: 2604 Controller Operation3.12. PARA
Page 57 and 58: 2604 Controller Programmer Operatio
Page 85 and 86: 2604 Controller Alarm Operation5. C
Page 87 and 88: 2604 Controller Alarm Operation5.2.
Page 99 and 100: 2604 Controller Appendix AA. APPEND
Page 101: 2604 Controller Appendix AA.2. CONF
Page 105 and 106: 2604 Controller Safety and EMC Info
Page 107 and 108: 2604 Controller Safety and EMC Info
Page 109 and 110: 2604 Controller Technical Specifica
show all

MODEL 2604 CONTROLLER - USER GUIDE - d a n m a r k

Create successful ePaper yourself

Delete template?

Save as template?