REGOLATORE CONTROLLER ATR121 ATR141 Manuale User ...
REGOLATORE CONTROLLER ATR121 ATR141 Manuale User ... REGOLATORE CONTROLLER ATR121 ATR141 Manuale User ...
Sensor : PT100 PT/NI100/1K PTC/NTC 6 7 8 9 10 11 12 RS485 PT/NI100/1K PTC/NTC 6 7 8 9 10 11 12 RS485 PT/NI100/1K PTC/NTC 6 7 8 9 10 11 12 RS485 Controller SLAVE 1 Mod. : ATR121-AT Controller SLAVE 2 Mod. : ATR121-AT Controller SLAVE 254 Mod. : ATR121-AT PERSONAL COMPUTER Serial line RS 485 Serial line RS 232 Converter Rs232 / Rs485 Automatic direction Mod. : PIX-RECORDER Use shielded cable 1 twisted pair. According to EIA RS-485. Suggested cable: Belden 9841. AN-0020-3704 30
22 CONFIGURATION MEMORANDUM Date: Model ATR121/141: Installer: Plant: Notes: Par. Description Default Prom. Select type of command output Sensor Type Visualization of decimal point Lower limit of setpoint 0 Upper limit of setpoint 31 ATR121 ATR141 999 1750 Lower limit only for V/I V/mA 0 Upper limit only for V/I V/mA 999 Latch On Function Offset calibration 0.0 Gain calibration 0 Type of action Type of contact for control output in case of anomaly Select state of OUT1 Hysteresis dead/band 0 Proportional band 0 Integral time 0 Derivative time 0 Proportional cycle time 10 Type of alarm Contact alarm OUT State of contact for alarm output in case of anomaly State of the LED Alarms hysteresis 0
- Page 1 and 2: REGOLATORE CONTROLLER ATR121 ATR141
- Page 3 and 4: 26 CAMBIO DEL SETPOINT ............
- Page 5 and 6: 3 CHANGE OF SETPOINT VALUE To modif
- Page 7 and 8: Serial communication A AD T T RS485
- Page 9 and 10: 9 ELECTRICAL WIRINGS Although this
- Page 11 and 12: Capacity 8V / 20mA for models A-B-C
- Page 13 and 14: Comparison value Hysteresis Operati
- Page 15 and 16: To assure optimal working of the un
- Page 17 and 18: 15 Proportional band Width of the p
- Page 19 and 20: Fahrenheit ATR141 30 ATR121 ATR141
- Page 21 and 22: has been modified. Display alternat
- Page 23 and 24: 18 FUNCTION NEUTRAL ZONE The Neutra
- Page 25 and 26: MODBUS ADDRESS DESCRIPTION READ/ WR
- Page 27 and 28: 2016 2017 2018 2019 2020 2021 2022
- Page 29: 21 SUPERVISORY SYSTEM WITH CONTROLL
- Page 33 and 34: 24 SEZIONE UTENTE 25 VISUALIZZATORI
- Page 35 and 36: Termocoppia aperta o temperatura fu
- Page 37 and 38: Protezione dati Parametri sotto pas
- Page 39 and 40: 12…24Vac ±10% 50Hz/60Hz 12…35V
- Page 41 and 42: Comunicazione compatibile RS485 con
- Page 43 and 44: 2 3 SET Incrementare la prima cifra
- Page 45 and 46: 8 ATR121 ATR141 Funzione Latch On (
- Page 47 and 48: L’intervento dell’allarme è as
- Page 49 and 50: 31 ATR121 Indirizzi slave 1-254 ATR
- Page 51 and 52: per selezionare . 40 FUNZIONE LATCH
- Page 53 and 54: morta” (vedi figura).In funzionam
- Page 55 and 56: 1 Versione software R 2 Riservato
- Page 57 and 58: 2021 2022 2023 2024 2025 2026 2027
- Page 59 and 60: 44 SUPERVISIONE CON ATR121 / 141 Es
- Page 61 and 62: Protezione set. Filtro software. 10
- Page 63 and 64: 48 DONNEES TECHNIQUES Caractéristi
- Page 65: 49 RACCORDS ÉLECTRIQUES Bien que c
22 CONFIGURATION MEMORANDUM<br />
Date:<br />
Model <strong>ATR121</strong>/141:<br />
Installer:<br />
Plant:<br />
Notes:<br />
Par. Description Default Prom.<br />
Select type of command output<br />
Sensor Type<br />
Visualization of decimal point<br />
Lower limit of setpoint 0<br />
Upper limit of setpoint<br />
31<br />
<strong>ATR121</strong><br />
<strong>ATR141</strong><br />
999<br />
1750<br />
Lower limit only for V/I V/mA 0<br />
Upper limit only for V/I V/mA 999<br />
Latch On Function<br />
Offset calibration 0.0<br />
Gain calibration 0<br />
Type of action<br />
Type of contact for control output in<br />
case of anomaly<br />
Select state of OUT1<br />
Hysteresis dead/band 0<br />
Proportional band 0<br />
Integral time 0<br />
Derivative time 0<br />
Proportional cycle time 10<br />
Type of alarm<br />
Contact alarm OUT<br />
State of contact for alarm output in case<br />
of anomaly<br />
State of the LED<br />
Alarms hysteresis 0