Passerelle in filo d'acciaio. Wire cable tray. - Electricalservices-co.com
Passerelle in filo d'acciaio. Wire cable tray. - Electricalservices-co.com
Passerelle in filo d'acciaio. Wire cable tray. - Electricalservices-co.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Dati tecnici.<br />
Technical data.<br />
Curve / Bends<br />
Come per le variazioni di piano, per poter eseguire le curve basta tagliare<br />
alcuni fili d’acciaio, piegare la passerella e fissare tra loro gli elementi <strong>co</strong>n<br />
l’apposito elemento per giunzioni curve (FCPGC6M).<br />
Same as for the changes of level, when your <strong>tray</strong> needs to make a bend,<br />
you just need to cut a few wires and then bend the other ones and fasten<br />
them with the bend-jo<strong>in</strong><strong>in</strong>g fitt<strong>in</strong>g (FCPGC6M).<br />
Dati tecnici.<br />
Technical data.<br />
Base Lunghezza / Length A<br />
100 1100 3<br />
150 1100 4<br />
200 1100 4<br />
300 1500 6<br />
400 1900 8<br />
500 2100 9<br />
600 2500 11<br />
Curve piane a 90° raggiate<br />
90° Radius bend<br />
1) Effettuare i tagli <strong>co</strong>me da disegno seguendo i dati riportati <strong>in</strong> tabella.<br />
2) Piegare la passerella <strong>co</strong>me da esempio e giuntarla mediante l’utilizzo<br />
delle apposite piastr<strong>in</strong>e.<br />
1) Cut ac<strong>co</strong>rd<strong>in</strong>g to draw<strong>in</strong>g and follow the data as per chart aside.<br />
2) Bend the <strong>tray</strong> as shown and fasten it by the specific Jo<strong>in</strong>t for bend FCPGC6M.<br />
FCPGC6M<br />
1<br />
Base Lunghezza / Length A<br />
100 700 100<br />
150 700 100<br />
200 1000 100<br />
300 1200 200<br />
400 1400 300<br />
500 1600 400<br />
600 1800 500<br />
1<br />
Curve piane a 90° non raggiate<br />
90° Bends<br />
1) Effettuare i tagli <strong>co</strong>me da disegno seguendo i dati riportati <strong>in</strong> tabella.<br />
2) Piegare la passerella <strong>co</strong>me da esempio.<br />
3) Unire la passerella <strong>co</strong>me da esempio.<br />
4) Giuntarla mediante l’utilizzo delle apposite piastr<strong>in</strong>e.<br />
1) Cut ac<strong>co</strong>rd<strong>in</strong>g to draw<strong>in</strong>g and follow the data as per chart aside.<br />
2) Bend the <strong>tray</strong> as shown.<br />
3) Jo<strong>in</strong> the <strong>tray</strong> as shown.<br />
4) Fasten the specific Jo<strong>in</strong>ts<br />
3<br />
for bend FCPGC6M.<br />
L<br />
A<br />
Base<br />
2<br />
5<br />
2<br />
A<br />
100<br />
100<br />
L 200<br />
A<br />
Base<br />
4<br />
FCPGC6M<br />
PASSERELLE IN FILO D’ACCIAIO / WIRE CABLE TRAY<br />
5.1.14<br />
www.canalplast.it - <strong>in</strong>fo@canalplast.it<br />
INSTALLAZIONE ACCIAIO / STEEL INSTALLATION<br />
5.1.15