Manuale utente_Owner's manual_Manuel d ... - Husqvarna
Manuale utente_Owner's manual_Manuel d ... - Husqvarna Manuale utente_Owner's manual_Manuel d ... - Husqvarna
ENGINE STARTING (TC) With cold engine, i.e., after the motorcycle has not been used for a while or in low ambient temperatures, operate in the following manner: 1) pull clutch lever (1); 2) pull starter knob (2); 3) shift gear pedal (3) to neutral position; 4) Press starter button (4). Take starter knob (2) back to its initial position as soon as engine stays idle. When starting with an already warmed up engine DO NOT USE the starter. When a cold engine has just been started, do not increase revs, to ensure an adequate oil warm-up and circulation. Note*: A safety switch is set on the clutch lever support. This switch allows you to ONLY start the engine with the gearbox idle, or with the gear engaged and the clutch lever pulled. IMPORTANT NEVER START ENGINE WITH BATTERY DIS- CONNECTED FROM CIRCUIT. 1 2 4 IMPORTANT NOTE IN CASE OF COLD START AT LOW TEM- PERATURES It is recommended to briefly warm up the engine at idle until, after having turned off the starting device, the engine response when opening the throttle is normal. This allows oil reaching all points that need lubricating and coolant to warm up to regular operating temperature. Avoid warming up the engine for too long. N 3 EN - 22
STOPPING THE MOTORCYCLE AND THE ENGINE - Close the throttle (1) completely in order to slow down the motorcycle. - Apply both front (2) and rear (3) brakes while downshifting (for fast deceleration, press firmly on both brake pedal and lever). - When stopped, pull the clutch lever (4) and shift gear lever (5) into the neutral position. TE 4 TE - To stop the engine, turn key (6) to OFF (key removal position). 6 EN 1 TC TC - TXC - To turn vehicle off, press push-button (7). 2 4 TC 7 TXC 3 5 7 EN - 23
- Page 28 and 29: CONTROLLO LIVELLO LIQUIDO DI RAFFRE
- Page 30 and 31: REGOLAZIONE CAVO COMANDO GAS Per ve
- Page 32 and 33: Per rimuovere la candela agire come
- Page 34 and 35: - allargare le due linguette di fer
- Page 36 and 37: REGISTRAZIONE POSIZIONE PEDALE FREN
- Page 38 and 39: SOSPENSIONI Le indicazioni che segu
- Page 40 and 41: LIVELLO OLIO FORCELLA Per il regola
- Page 42 and 43: REGISTRAZIONE FRENO IDRAULICO AMMOR
- Page 44 and 45: Lavaggio catena senza anelli OR (TC
- Page 46 and 47: RIMONTAGGIO RUOTA ANTERIORE - Monta
- Page 48 and 49: SMONTAGGIO PASTIGLIE FRENO - Rimuov
- Page 50 and 51: SOSTITUZIONE LAMPADINE PROIETTORE (
- Page 52 and 53: SOSTITUZIONE LAMPADA LUCE TARGA (TE
- Page 54 and 55: ❏ Freni / Frizione Controllo circ
- Page 57 and 58: ENGLISH EN EN - 1
- Page 59 and 60: PRESENTATION Welcome to the Husqvar
- Page 61 and 62: IDENTIFICATION DATA The engine iden
- Page 63 and 64: FRONT BRAKE Fixed disc type .......
- Page 65 and 66: LEGEND 1. Front wheel 2. Front brak
- Page 67 and 68: LEGEND 1. Front wheel 2. Front brak
- Page 69 and 70: SIDE STAND A side stand (1) is supp
- Page 71 and 72: 2- SPEED / CLOCK (figure 2) - SPEED
- Page 73 and 74: STEERING LOCK (TE) The motorcycle i
- Page 75 and 76: GEAR SHIFT CONTROL The lever (1) is
- Page 77: ENGINE STARTING (TE-TXC) With cold
- Page 81 and 82: ENGINE OIL REPLACEMENT AND MESH FIL
- Page 83 and 84: - Pour the necessary quantity of co
- Page 85 and 86: IDLE ADJUSTMENT Adjust the carburet
- Page 87 and 88: AIR FILTER CHECK - Turn pin (1) cou
- Page 89 and 90: ADJUSTMENT OF THE CONTROL LEVER AND
- Page 91 and 92: REAR BRAKE FLUID LEVEL CHECK Fluid
- Page 93 and 94: ADJUSTING THE FRONT FORK a) COMPRES
- Page 95 and 96: ADJUSTING THE SHOCK ABSORBER SPRING
- Page 97 and 98: If it is not, proceed as follows: -
- Page 99 and 100: REMOVING THE FRONT WHEEL Set a stan
- Page 101 and 102: TYRES BRAKES Care should be taken t
- Page 103 and 104: BATTERY The sealed battery does not
- Page 105 and 106: To replace the parking light bulb (
- Page 107 and 108: APPENDIX LONG PERIOD OF INACTIVITY
- Page 109: ALPHABETICAL INDEX Page A ADJUSTING
- Page 112 and 113: SOMMAIRE Page PRÉSENTATION........
- Page 114 and 115: IMPORTANT Pour maintenir la « Gara
- Page 116 and 117: FR - 6 DONNÉES TECHNIQUES MOTEUR T
- Page 118 and 119: VUE GÉNÉRALE DE LA MOTO - TE 16 1
- Page 120 and 121: VUE GÉNÉRALE DE LA MOTO - TC - TX
- Page 122 and 123: ROBINETS CARBURANT COMMANDES Les de
- Page 124 and 125: AFFICHEUR NUMÉRIQUE, VOYANTS (TE)
- Page 126 and 127: POIGNÉE DES GAZ La poignée (1) de
ENGINE STARTING (TC)<br />
With cold engine, i.e., after the motorcycle has not<br />
been used for a while or in low ambient temperatures,<br />
operate in the following manner:<br />
1) pull clutch lever (1);<br />
2) pull starter knob (2);<br />
3) shift gear pedal (3) to neutral position;<br />
4) Press starter button (4).<br />
Take starter knob (2) back to its initial position as<br />
soon as engine stays idle. When starting with an<br />
already warmed up engine DO NOT USE the starter.<br />
When a cold engine has just been started, do not<br />
increase revs, to ensure an adequate oil warm-up<br />
and circulation.<br />
Note*:<br />
A safety switch is set on the clutch lever support. This<br />
switch allows you to ONLY start the engine with the<br />
gearbox idle, or with the gear engaged and the clutch<br />
lever pulled.<br />
IMPORTANT<br />
NEVER START ENGINE WITH BATTERY DIS-<br />
CONNECTED FROM CIRCUIT.<br />
1<br />
2<br />
4<br />
IMPORTANT NOTE IN CASE OF COLD START AT LOW TEM-<br />
PERATURES<br />
It is recommended to briefly warm up the engine at idle<br />
until, after having turned off the starting device, the engine<br />
response when opening the throttle is normal.<br />
This allows oil reaching all points that need lubricating and<br />
coolant to warm up to regular operating temperature.<br />
Avoid warming up the engine for too long.<br />
N<br />
3<br />
EN - 22