Programma TaeguTMill

κ = 90°
Fig.1
Spot Face
κ = 90°
Fig.2
Drill Mill
TSF - - / TDM - -
Descrizione
TSF-112-W16-06
Inserto
Dimensioni (mm)
D d L l
Fig.
Max. Prof. di
foratura, Cd
prof.
frsatura, ap
1 12 16 80 27 x 1 18 5.6
TSF-216-W20-06 XOMT 060204
2 16 20 90 27 x 1 18 5.6
TSF-320-W20-06 3 20 20 100 25 x 1 18 5.6
TSF -222-W25-09
SPMG 090408-EM 2 22 25 100 40 x 1 28 9
TSF-225-W25-09 SPMT 090408-EM 2 25 25 100 40 x 1 28 9
TSF-332-W32-11
SPMG 110408-EM 3 32 32 115 50 x 1 39 10.7
TSF-440-W32-11 SPMT 110408-EM 4 40 32 125 55 x 1 39 10.7
TSF-445-W32-14
SPMG 140508-EM 4 45 32 130 70 x 1 50 13.4
TSF-450-W32-14 SPMT 140508-EM 4 50 32 140 80 x 1 60 13.4
TDM-112-W16-06
1 12 16 80 20 2 12 5.6
TDM-216-W20-06 2 16 20 90 25 2 16 5.6
TDM -218-W20-06 XOMT 060204
2 18 20 90 25 2 16 5.6
TDM-220-W25-06 2 20 25 100 40 2 20 5.6
TDM -222-W25-06 2 22 25 110 47 2 25 5.6
TDM-225-W25-09
SPMG 090408-EM 2 25 25 110 50 2 30 9
TDM-228-W32-09 SPMT 090408-EM 2 28 32 125 60 2 38 9
TDM-232-W32-11
SPMG 110408-EM 2 32 32 125 60 2 38 10.7
TDM-240-W32-11 SPMT 110408-EM 2 40 32 125 60 2 38 10.7
TDM-245-W32-14
SPMG 110408-EM 2 45 32 130 66 2 40 13.4
TDM-250-W32-14 SPMT 110408-EM 2 50 32 150 66 2 40 13.4
• Per i parametri di taglio vedere a pagina E185
Inserto
Forma
Grado Principale
XOMT SPMG SPMT
Acciaio
TT9080
TT8020
TT7080
Ghisa TT6080
Max.
ap
Max.
Cd
• Per gli inserti vedere a pagina E42
Ricambi
Inserto Vite Chiave
Misura
TSF-D12, TDM-D12 XOMT 060204 TS 22046I TD7
TSF-D16~20, TDM-D16~20 XOMT 060204 TS 22052I/HG TD7
TSF-D22~25, TDM-D22~25 SPMG/T 090408-EM TS 35088I TD10
TSF-D32~40, TDM-D32~40 SPMG/T 110408-EM TS 40093I TD15
TSF-D45~50, TDM-D45~50 SPMG/T 140508-EM TS 50A121I/HG TD20
E 75