BR 60/95 RS Bp BR 60/95 RS Bp Pack BD 60/95 RS Bp ... - Kärcher
BR 60/95 RS Bp BR 60/95 RS Bp Pack BD 60/95 RS Bp ... - Kärcher
BR 60/95 RS Bp BR 60/95 RS Bp Pack BD 60/95 RS Bp ... - Kärcher
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>BR</strong><br />
Set the drive direction<br />
using<br />
the drive direction<br />
button at<br />
the operator<br />
console.<br />
Select speed<br />
range using the<br />
speed button (3<br />
stages).<br />
<strong>BD</strong><br />
Observe the<br />
display and wait<br />
till the controls<br />
are initialized.<br />
Set the drive direction<br />
using<br />
the drive direction<br />
button at<br />
the operator<br />
console.<br />
Select speed<br />
range using the<br />
speed button (3<br />
stages).<br />
Press the unlocking key.<br />
Press the accelerator carefully to drive.<br />
<br />
Note<br />
The drive direction can also be changed<br />
during the drive. You can thus clean very<br />
dirty surfaces by driving back and forth a<br />
couple of times.<br />
Overload<br />
In case of overloading, the drive motor automatically<br />
switches off after a certain period.<br />
Allow machine to cool down at least for<br />
15 minutes.<br />
Press again the drive fuse on the operating<br />
panel.<br />
Cleaning<br />
<strong>BR</strong><br />
Press downward<br />
the lever<br />
for lowering the<br />
vacuum bar.<br />
The varuum bar<br />
is lowered and<br />
the suction is<br />
activated.<br />
Lower the<br />
cleaning head<br />
by pressing the<br />
button for brush<br />
contact pressure.<br />
Note<br />
The detergent supply and brush drive are<br />
interrupted till further movement if the device<br />
stands at one place for more than 2<br />
seconds.<br />
Press accelerator pedal and drive to the<br />
surface to be cleaned.<br />
<strong>BR</strong><br />
Adjust the detergent<br />
flow using<br />
the water<br />
regulation<br />
knob.<br />
<strong>BD</strong><br />
Press Cleaning<br />
operations key.<br />
The brush drive<br />
is activated.<br />
The cleaning<br />
head is lowered<br />
(slight brush<br />
contact pressure)<br />
and the<br />
detergent liquid<br />
is supplied.<br />
The varuum bar<br />
is lowered and<br />
the suction is<br />
activated.<br />
<strong>BD</strong><br />
Adjust the detergent<br />
flow using<br />
the Dosing<br />
Liquid Detergent<br />
switch (4<br />
stages).<br />
Adjust brush contact pressure using the<br />
Brush Contact Pressure switch (4 stages).<br />
<strong>BR</strong><br />
Select speed<br />
range using the<br />
speed button (3<br />
stages).<br />
In cleaning mode, the highest speed is limited<br />
to Stage II.<br />
Note<br />
Very dirty floors can be cleaned in two<br />
rounds. In the first work step, the detergent<br />
liquid is applied and brushed in. The vacuum<br />
bar is raised by pressing the Raise/Lower<br />
Vacuum Bar switch. In the <strong>BD</strong> model,<br />
the rear spray guard (Aqua-Mizer) also<br />
needs to be removed. The surface is<br />
cleaned normally in the second step after<br />
the detergent has worked normally.<br />
Complete cleaning<br />
<strong>BR</strong><br />
Raise the<br />
cleaning head<br />
by pressing the<br />
Brush Contact<br />
Pressure<br />
switch.<br />
Pull the vacuum<br />
bar lowering lever<br />
upward; the<br />
vacuum bar is<br />
raised and the<br />
suction is<br />
switched off.<br />
<strong>BD</strong><br />
Select speed<br />
range using the<br />
speed button (3<br />
stages).<br />
Note<br />
After raising the cleaning head, drive further<br />
approx. 5 m so that the remaining water is<br />
sucked off.<br />
Shutting down<br />
Park the machine on an even surface.<br />
Turn key to "0" and remove it.<br />
Empty tanks.<br />
Drain off dirt water<br />
<strong>BD</strong><br />
Press Cleaning<br />
operations key.<br />
The brush drive<br />
is switched off<br />
and the cleaning<br />
head is<br />
raised.<br />
The vacuum<br />
bar is raised after<br />
15 seconds.<br />
The suction is<br />
switched off after<br />
30 seconds.<br />
Note<br />
Overflow dirt water tank. The suction flow is<br />
interrupted by the swimmer when the dirt water<br />
tank is full. Empty the dirt water reservoir.<br />
Warning<br />
Please observe the local provisions regarding<br />
the wastewater treatment.<br />
Take the dirt water discharge hose from<br />
the support and lower above a suited<br />
collection device.<br />
Let off dirt water by opening the screw<br />
lid at the discharge hose.<br />
Rinse the dirt water tank with clear water.<br />
Clean the swimmer and check the<br />
movement of the swimmer ball.<br />
Rinse the dirt water tank with clear water.<br />
Drain off clean water<br />
Pull out the drain hose for fresh water<br />
(located behind the drain hose for dirt<br />
water) and lower it into a suitable collection<br />
system.<br />
Let off detergent by opening the screw<br />
lid at the discharge hose.<br />
Emptying waste container<br />
(only <strong>BR</strong> model)<br />
Lift the cleaning head.<br />
Turn key to "0" and remove it.<br />
Loosen the cross-handle of the spray<br />
guard and tilt the spray guard to the<br />
side.<br />
Remove the waste container.<br />
Empty the waste container and rinse<br />
with water.<br />
Danger<br />
Risk of injury! When loading or unloading<br />
the machine, it may only be operated on<br />
gradients of max. 2%. Drive slowly.<br />
Remove vacuum bar, brushes and<br />
spray guard from the device.<br />
If you want to transport the machine on<br />
a vehicle secure it from slipping using<br />
belts/ ropes.<br />
1 Fastening points<br />
Transport<br />
Maintenance and care<br />
Danger<br />
Risk of injury! Before carrying out any tasks<br />
on the machine, set the main key to "0" and<br />
remove it. Pull out the battery plug.<br />
English 19
Change language