You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
CAUTION: The engine must have completely<br />
cooled down before storing the lawnmower.<br />
NOTE:<br />
- When storing any type of power equipment in an<br />
unventilated or material storage shed,<br />
- Care should be taken to rust-proof the equipment.<br />
Using a light oil or silicone, coat the equipment,<br />
especially cables and all moving parts.<br />
13. TROUBLE SHOOTING<br />
- Be careful not to bend or kink cables.<br />
- If the starter rope becomes disconnected from rope<br />
guide on handle, disconnect and ground the spark plug<br />
wire. Depress the blade control handle and pull the<br />
starter rope out from engine slowly. Slip the starter<br />
rope into the rope guide bolt on handle.<br />
Transport<br />
Turn the engine off. Ensure not to bend or damage the<br />
cutter when pushing the lawnmower over obstacles.<br />
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION<br />
Throttle chock not in the correct<br />
position for the prevailing conditions.<br />
Move throttle chock to correct position.<br />
Fuel tank is empty.<br />
Fill tank with fuel: refer to ENGINE OWNERS<br />
MANUAL.<br />
Air cleaner element is dirty.<br />
Clean air cleaner element: refer to ENGINE<br />
OWNERS MANUAL.<br />
Spark plug loose. Tighten spark plug to 25 - 30 Nm.<br />
Engine does not start.<br />
Spark plug wire loose or disconnected<br />
from plug.<br />
Install spark plug wire on spark plug.<br />
Spark plug gap is incorrect. Set gap between electrodes at 0.7 to 0.8 mm.<br />
Spark plug is defective.<br />
Install new, correctly gapped plug: refer to ENGINE<br />
OWNERS MANUAL.<br />
Remove air cleaner element and pull starter rope<br />
Carburetor is flooded with fuel. continuously until carburetor clears itself and install<br />
air cleaner element.<br />
Faulty ignition module. Contact Dolmar authorised service centre.<br />
Engine difficult to start or<br />
Dirt, water, or stale fuel tank.<br />
Drain fuel and clean tank. Fill tank with clean, fresh<br />
fuel.<br />
loses power.<br />
Vent hole in fuel tank cap is plugged. Clean or replace fuel tank cap.<br />
Air cleaner element is duty. Clean air cleaner element.<br />
Spark plug is detective.<br />
Install new, correctly gapped plug: refer to ENGINE<br />
OWNERS MANUAL.<br />
Engine operates<br />
erratically.<br />
Spark plug gap is incorrect. Set gap between electrodes at 0.7 to 0.8 mm.<br />
Air cleaner element is dirty.<br />
Clean air cleaner element: refer to ENGINE<br />
OWNERS MANUAL.<br />
Air cleaner element is dirty.<br />
Clean air cleaner element: refer to ENGINE<br />
OWNERS MANUAL.<br />
Engine idles poorly. Air slots in engine shroud are blocked. Remove debris from shots.<br />
Cooling fins and air passages under<br />
engine blower housing are blocked.<br />
Remove debris from cooling fins and air passages.<br />
Engine skips at high<br />
speed.<br />
Gap between electrodes of spark plug<br />
is too close.<br />
Set gap between electrodes at 0.7 to 0.8 mm.<br />
Engine overheats.<br />
Cooling air flow is restricted.<br />
Incorrect spark plug.<br />
Remover any debris from slots in shroud, blower<br />
housing, air passages.<br />
Install RJ19LMC spark plug and cooling fins on<br />
engine.<br />
Mower vibrates<br />
Cutting assembly is loose. Tighten blade.<br />
abnormally.<br />
Cutting assembly is unbalanced. Balance blade.<br />
13