SEP 40

More documents

Recommendations

Info

BUFFER OPERATIONS - View/edit, find/replace - Fill/copy, move, byte swap, word/dword split - Checksum (byte, word) - Print - File load/save - No download time because programmer is PC controlled - Automatic file type identification SUPPORTED FILE FORMATS grifo ® ITALIAN TECHNOLOGY - Unformatted (raw) binary - HEX: Intel, Intel EXT, Motorola S-record, MOS, Exormax, Tektronix, ASCII-space-HEX PACKAGE INCLUDED - Programmer - Cable with two 25 pin, D-type connectors for connecting the programmer to the PC - External power supply (suitable for respective programmer) - Diagnostic POD for selftest of programmer - Cap for ZIF socket (anti-dust cover) - Mini-CD with the control program, this User’s manual and additional files - Shipping case Page 64 SEP 40 Rel. 3.10
ITALIAN TECHNOLOGY grifo ® ISP (IN-SYSTEM PROGRAMMING) In-system programming allows programming and reprogramming of device positioned inside the end system. Using a simple interface, the ISP programmer communicates serially with the device, reprogramming nonvolatile memories on the chip. In-system programming eliminates the physical removal of chips from the system. This will save time, and money, both during development in the lab, and when updating the software or parameters in the field. Target device is the device (microcontroller, PLD, etc…), which is to be in-system programmed. Target system is the physical Printed Circuit Board (PCB) which contains the device to be in-system programmed. GENERAL RULES FOR IN-SYSTEM PROGRAMMING Please refer to figure 5. We recommend respect following rules to avoid damages to PC, ISP programmer, target device or target system: - Ensure common earth point for target system, ISP programmer and PC. - For laptop or other PC which is not connected to common earth point: make hard - wired connection from laptop to common earth point (for example use LPT or COM port D – connector). Any devices connected to target system must be connected to common earth point too. During in-system programming you connect two electrical devices – ISP programmer and target system. Unqualified connection can damage these devices. NOTE: When you don’t keep below directions and you damage programmer during in-system programming, it is damage of programmer by unqualified manipulation and is out of warranty. 1. Turn off both devices – ISP programmer and target device. 2. Assign same GND potential for all devices, e.g. connect GND of all devices by wire. 3. Insert one connector of ISP cable to ISP programmer, turn on programmer and control program. 4. In control program select target device and operation options. 5. Start action on target device (read, program). 6. After direction of control program, connect other ISP cable connector to target system and turn on it. 7. After direction of control program, disconnect other ISP cable connector from target system and turn off it. 8. If you need another action on target device, you continue with step 5. NOTE: If target system use signals needed for ISP programming, it’s necessary separate them from target device by appropriate resistors. SEP 40 Rel. 3.10 Page 65
Page 1:
Via dell' Artigiano, 8/6 40016 San
Page 4 and 5:
DOCUMENTATION COPYRIGHT BY grifo ®
Page 6 and 7:
grifo ® ITALIAN TECHNOLOGY LISTA D
Page 8 and 9:
grifo ® ITALIAN TECHNOLOGY GENERAL
Page 10 and 11:
grifo ® ITALIAN TECHNOLOGY FIGURES
Page 12 and 13:
INFORMAZIONI PRELIMINARI grifo ® I
Page 14 and 15:
grifo ® ITALIAN TECHNOLOGY SEP 40
Page 16 and 17:
CARATTERISTICHE TECNICHE ELEMENTI D
Page 18 and 19:
TEMPI DI PROGRAMMAZIONE grifo ® IT
Page 20 and 21:
OPERAZIONI SUL BUFFER grifo ® ITAL
Page 22 and 23:
STRUTTURA CONSIGLIATA DEL CONNETTOR
Page 24 and 25: INSTALLAZIONE CONNESSIONE DI SEP 40
Page 26 and 27: SELFTEST E CALIBRAZIONE grifo ® IT
Page 28 and 29: AVVIO RAPIDO grifo ® ITALIAN TECHN
Page 30 and 31: INSTALLAZIONE SOFTWARE grifo ® ITA
Page 32 and 33: grifo ® ITALIAN TECHNOLOGY La sele
Page 34 and 35: grifo ® ITALIAN TECHNOLOGY Le info
Page 36 and 37: grifo ® ITALIAN TECHNOLOGY Device
Page 38 and 39: grifo ® ITALIAN TECHNOLOGY del dis
Page 42 and 43: grifo ® ITALIAN TECHNOLOGY addr -
Page 46 and 47: grifo ® ITALIAN TECHNOLOGY F7 stri
Page 48 and 49: Buffer / Erase Riempie il buffer co
Page 50 and 51: grifo ® ITALIAN TECHNOLOGY La seco
Page 52 and 53: grifo ® ITALIAN TECHNOLOGY Port -
Page 54 and 55: grifo ® ITALIAN TECHNOLOGY Per tor
Page 56 and 57: grifo ® ITALIAN TECHNOLOGY About F
Page 58 and 59: RISOLUZIONE DEI PROBLEMI grifo ® I
Page 60 and 61: ARTICOLI AGGIUNTIVI grifo ® ITALIA
Page 62 and 63: G GARANZIA 45 GOOD LED 13 H HANDLER
Page 64 and 65: grifo ® ITALIAN TECHNOLOGY Pagina
Page 66 and 67: PRELIMINARY INFORMATION grifo ® IT
Page 68 and 69: grifo ® ITALIAN TECHNOLOGY The ric
Page 70 and 71: TECHNICAL FEATURES SEP 40 ELEMENTS
Page 72 and 73: PROGRAMMING SPEED grifo ® ITALIAN
Page 76 and 77: grifo ® ITALIAN TECHNOLOGY THE REC
Page 78 and 79: INSTALLATION CONNECTING SEP 40 TO T
Page 80 and 81: SELFTEST AND CALIBRATION grifo ® I
Page 82 and 83: QUICKSTART grifo ® ITALIAN TECHNOL
Page 84 and 85: SOFTWARE INSTALLATION grifo ® ITAL
Page 86 and 87: grifo ® ITALIAN TECHNOLOGY Menu se
Page 88 and 89: grifo ® ITALIAN TECHNOLOGY project
Page 92 and 93: grifo ® ITALIAN TECHNOLOGY the dev
Page 94 and 95: grifo ® ITALIAN TECHNOLOGY The Inc
Page 96 and 97: grifo ® ITALIAN TECHNOLOGY addr -
Page 98 and 99: grifo ® ITALIAN TECHNOLOGY Reload
Page 100 and 101: grifo ® ITALIAN TECHNOLOGY F6 prin
Page 102 and 103: grifo ® ITALIAN TECHNOLOGY by topi
Page 104 and 105: grifo ® ITALIAN TECHNOLOGY is read
Page 106 and 107: grifo ® ITALIAN TECHNOLOGY the pro
Page 108 and 109: grifo ® ITALIAN TECHNOLOGY Protect
Page 110 and 111: grifo ® ITALIAN TECHNOLOGY Help /
Page 112 and 113: TROUBLESHOOTING grifo ® ITALIAN TE
Page 114 and 115: ADDITIONAL TOOLS grifo ® ITALIAN T
Page 116 and 117: H HANDLER 42 HELP 45 HEX 2, 10 HOT
Page 118: grifo ® ITALIAN TECHNOLOGY Page 10
show all

SEP 40

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?