MS-245.4 U/MS-245.4 UE/MS-245.4 C/MS-245.4 CE GB Petrol ...
MS-245.4 U/MS-245.4 UE/MS-245.4 C/MS-245.4 CE GB Petrol ... MS-245.4 U/MS-245.4 UE/MS-245.4 C/MS-245.4 CE GB Petrol ...
DESIGNATION OF PARTS MS-245.4 U MS-245.4 UE ⑮ ⑪ ⑬ ④ ⑯ ⑰ ⑳ ③ ⑲ ⑫ ⑭ ⑨ ⑤ ② ⑩ ⑦ 10 MS-245.4 C MS-245.4 CE ⑥ ① ⑮ 21 22 ⑬ ⑱ ⑨ ⑩ ⑭ ④ ⑫ ⑤ ⑪ ⑧ GB DESIGNATION OF PARTS 1 Fuel tank 2 Rewind starter 3 Air cleaner 4 I-O switch (on/off) 5 Spark plug 6 Exhaust muffler 7 Clutch case 8 Rear grip 9 Hanger 10 Handle 11 Control lever 12 Control cable 13 Shaft 14 Protector 15 Gear Case/Head case 16 Handle holder 17 Cutter blade 18 Nylon cutting head 19 Fuel filler cap 20 Starter knob 21 Exhaust pipe 22 Oil gauge ⑦
MOUNTING OF HANDLE CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves! CAUTION: Start the Petrol Brushcutter only after having assembled it completely. For machines with bike handle models – Loosen knob (1). – Place handle (4) between handle clamp (2) and handle holder (3). – Adjust handle (4) to an angle that provides a comfortable working position and then secure by firmly hand-tightening knob (1). CAUTION: Do not forget to mount spring (5). For machines with loop handle – Fix a barrier to the left side of the machine together with the handle for operator protection. – Do not adjust position of the loop handle too close to the control grip. Keep not less than 250 mm distance between the handle and the grip. (a distance collar is provided for this purpose.) 11 Engine (4) Engine (3) (1) (2) (5)
- Page 1 and 2: MS-245.4 U/MS-245.4 UE/MS-245.4 C/M
- Page 3 and 4: Thank you very much for purchasing
- Page 5 and 6: Start the Petrol Brushcutter only i
- Page 7 and 8: Never straighten or weld damaged cu
- Page 9: TECHNICAL DATA MS-245.4 UE, MS-245.
- Page 13 and 14: MOUNTING OF CUTTER BLADE OR NYLON C
- Page 15 and 16: Point 2 in Replacement of oil: “I
- Page 17 and 18: 2) Set the I-O switch (1) to OPERAT
- Page 19 and 20: NYLON CUTTING HEAD The nylon cuttin
- Page 21 and 22: 3) Place waste or paper near the oi
- Page 23 and 24: STORAGE Fault location WARNING: Whe
- Page 25 and 26: TROUBLESHOOTING Before making a req
- Page 27 and 28: CONSIGNES DE SÉCURITÉ Instruction
- Page 29 and 30: Mode d’emploi - N’utilisez la d
- Page 31 and 32: DONNÉES TECHNIQUES MS-245.4 U, MS-
- Page 33 and 34: NOMENCLATURE DES PIÈCES MS-245.4 U
- Page 35 and 36: MONTAGE DU DISPOSITIF DE PROTECTION
- Page 37 and 38: AVANT DE COMMENCER Inspection et re
- Page 39 and 40: MANIEMENT CORRECT DE LA MACHINE Att
- Page 41 and 42: B : Démarrage après avoir fait ch
- Page 43 and 44: - Alignez la protubérance du desso
- Page 45 and 46: VÉRIFICATION DE LA BOUGIE - N’ut
- Page 47 and 48: Élément Huile du moteur Serrage d
- Page 49 and 50: Herzlichen Glückwunsch, dass Sie s
- Page 51 and 52: Starten Sie die Motorsense nur gem
- Page 53 and 54: Begradigen oder schweißen Sie niem
- Page 55 and 56: TECHNISCHE DATEN MS-245.4 UE, MS-24
- Page 57 and 58: MONTIEREN DES GRIFFS ACHTUNG: Stopp
- Page 59 and 60: MONTIEREN DER SCHNEIDKLINGE / DES N
DESIGNATION OF PARTS<br />
<strong>MS</strong>-<strong>245.4</strong> U<br />
<strong>MS</strong>-<strong>245.4</strong> <strong>UE</strong><br />
⑮<br />
⑪<br />
⑬<br />
④<br />
⑯<br />
⑰<br />
⑳<br />
③<br />
⑲<br />
⑫<br />
⑭<br />
⑨<br />
⑤<br />
②<br />
⑩<br />
⑦<br />
10<br />
<strong>MS</strong>-<strong>245.4</strong> C<br />
<strong>MS</strong>-<strong>245.4</strong> <strong>CE</strong><br />
⑥<br />
①<br />
⑮<br />
21<br />
22<br />
⑬<br />
⑱<br />
⑨<br />
⑩<br />
⑭<br />
④<br />
⑫<br />
⑤<br />
⑪<br />
⑧<br />
<strong>GB</strong> DESIGNATION OF PARTS<br />
1 Fuel tank<br />
2 Rewind starter<br />
3 Air cleaner<br />
4 I-O switch (on/off)<br />
5 Spark plug<br />
6 Exhaust muffler<br />
7 Clutch case<br />
8 Rear grip<br />
9 Hanger<br />
10 Handle<br />
11 Control lever<br />
12 Control cable<br />
13 Shaft<br />
14 Protector<br />
15 Gear Case/Head case<br />
16 Handle holder<br />
17 Cutter blade<br />
18 Nylon cutting head<br />
19 Fuel filler cap<br />
20 Starter knob<br />
21 Exhaust pipe<br />
22 Oil gauge<br />
⑦