PC-7612V PC-7614V
PC-7612V PC-7614V PC-7612V PC-7614V
V-belt SERVICE 1. Adjusting V-belt tension • If the cutting disc halts in mid operation easily, the V-belt has slackened. If this is the case, adjust tension using the following procedure. (1) Loosen belt cover tightening nuts. (2) Turn the tension adjustment screw to the right (clockwise) until the indicator nut reaches the marked position in order to increase the tension of the V-belt. (3) Once V-belt tensioning is complete, firmly retighten the belt cover tightening nuts. • If the cutting disc stops easily even though the tension of the V-belt has been adjusted, or the V-belt breaks, replace with a new V-belt. 2. Changing the V-belt (1) Loosen tightening nut, and turn tension adjustment screw to the left until the end of the screw is visible. (2) Remove tightening nuts, and then remove belt cover. (3) Next, remove the three mounting screws, and remove the clutch cover. (4) Remove the old V-belt, and fit on a new V-belt. Now, remount the clutch cover followed by belt cover. (5) Adjust tension as shown in the Adjusting V-belt tension section. Cleaning the protection hood Over time, the inside of the protection hood can become caked with material residue (especially from wet cutting), which if allowed to accumulate can hinder the free rotation of the cutting disc. For this reason the hood must be cleaned out from time to time. Take off the cutting wheel and remove the accumulated material from inside the hood with a strip of wood or similar implement. Clean the shaft and all disassembled parts with a cloth. NOTE: To install the cutting wheel see “Mounting the cutting disc”. 18 IMPORTANT: Because many of the parts and assemblies not mentioned in this Instruction Manual are vital to the safety of the unit, and because all parts are subject to a certain amount of wear and tear, it is important for your own safety that you have the unit checked and maintained regularly by a DOLMAR service center. IMPORTANT: Indication nut If the cutting wheel breaks during cutting, the Power Cutter must be repaired by a DOLMAR service centre before being used again! Clutch cover Hex. nut Mark Hex. nut Belt cover Tensioning screw Belt cover Tensioning screw End of screw
Cover lock Prefilter Filter cover Star-shaped screws Inner filter Air filter Loosen Top cover Top cover Star-shaped screws Dust bag filter 19 Cleaning/changing the air filter • If the air filter becomes clogged, it may cause poor engine performance. Therefore, every time after using the Power Cutter, be sure to clean the air filter in the following way. • Turn the cover lock to the left and remove it. • Remove the top cover after blowing off dust from it. • Next, remove the prefilter. • Remove the four star-shaped screws. • Remove the filter cover. • Remove the air filter. • Remove the dust bag filter from the filter cover and gently tap and blow on it to clean. • Gently tap and blow on the inner filter to remove dirt and dust. Also, periodically wash the inner filter in soapy water and dry thoroughly. • To clean the air filter tap it gently. If an air compressor is to be used, blow the compressed air onto the inside of the air filter. Do not wash the air filter. • Blow off dust from around the filters. • Reassemble the air filter to filter cover once cleaning is finished. • Tighten the cover lock firmly.
- Page 1 and 2: Original Instruction Manual Instruc
- Page 3 and 4: Delivery inventory Symbols 2 3 4 5
- Page 5 and 6: - Always wear safety shoes or boots
- Page 7 and 8: Kickback and lock-in - When working
- Page 9 and 10: In wet cutting, the disc is wetted
- Page 11 and 12: Technical data Item Model Engine Di
- Page 13 and 14: 2 8 4 5 6 7 Schematic drawing 6 1 1
- Page 15 and 16: Oil tank cap Fuel tank cap Level Fu
- Page 17: Adjusting the carburetor NOTE: This
- Page 21 and 22: Cleaning the starter When the start
- Page 23 and 24: SPECIAL ACCESSORIES Diamond cutting
- Page 25 and 26: Troubleshooting Before making a req
- Page 27 and 28: Français (Instructions d’origine
- Page 29 and 30: PRÉCAUTIONS DE SÉCURITÉ Précaut
- Page 31 and 32: Disques de coupe - Le capot de prot
- Page 33 and 34: Découpe de métal IMPORTANT ! Port
- Page 35 and 36: Maintenance - Avant de procéder au
- Page 37 and 38: Désignation des pièces 1. Poigné
- Page 39 and 40: Serrage de la courroie trapézoïda
- Page 41 and 42: Fonctionnement Démarrage AVERTISSE
- Page 43 and 44: Courroie trapézoïdale ENTRETIEN 1
- Page 45 and 46: Entretien de la bougie (1) Desserre
- Page 47 and 48: Extrémité de la vis Pince coupant
- Page 49 and 50: Tableau d’entretien • Élément
- Page 51 and 52: Entreposage AVERTISSEMENT : Lors de
- Page 53 and 54: Lieferumfang Symbole 2 3 4 5 1. Tre
- Page 55 and 56: - Tragen Sie stets Arbeitsschutzsch
- Page 57 and 58: Rückschlag und Einrasten - Wenn Si
- Page 59 and 60: Beim Nassschnitt wird die Scheibe z
- Page 61 and 62: Technische Daten Position Modell Mo
- Page 63 and 64: 2 8 4 5 6 7 Schematische Darstellun
- Page 65 and 66: Öltankdeckel Kraftstoff- Tankdecke
- Page 67 and 68: Einstellen des Vergasers HINWEIS: D
Cover lock<br />
Prefilter<br />
Filter cover<br />
Star-shaped<br />
screws<br />
Inner filter<br />
Air filter<br />
Loosen<br />
Top cover<br />
Top cover<br />
Star-shaped<br />
screws<br />
Dust bag filter<br />
19<br />
Cleaning/changing the air filter<br />
• If the air filter becomes clogged, it may cause poor engine<br />
performance. Therefore, every time after using the Power<br />
Cutter, be sure to clean the air filter in the following way.<br />
• Turn the cover lock to the left and remove it.<br />
• Remove the top cover after blowing off dust from it.<br />
• Next, remove the prefilter.<br />
• Remove the four star-shaped screws.<br />
• Remove the filter cover.<br />
• Remove the air filter.<br />
• Remove the dust bag filter from the filter cover and gently tap<br />
and blow on it to clean.<br />
• Gently tap and blow on the inner filter to remove dirt and dust.<br />
Also, periodically wash the inner filter in soapy water and dry<br />
thoroughly.<br />
• To clean the air filter tap it gently. If an air compressor is to be<br />
used, blow the compressed air onto the inside of the air filter.<br />
Do not wash the air filter.<br />
• Blow off dust from around the filters.<br />
• Reassemble the air filter to filter cover once cleaning is<br />
finished.<br />
• Tighten the cover lock firmly.