STIGA TITAN

5. Clean the inside of the cup (14:H).
6. Check that the O-ring (14:G) is intact and reinstall
the components with new filter in reverse
order.
7. Open the tap.
8. Bleed the fuel system. See “5.13”.
6.6 Tyre pressure
Set the tyre pressures to their default pressures.
Pressure front and rear: 0.9 bar.
See pressures in the manual for relevant implement.
6.7 Changing engine oil, filter
The engine oil may be very hot if it is
drained off directly after the engine is
shut off. So allow the engine to cool a
few minutes before draining the oil.
Change engine oil and filter as follows:
1. Place the machine on a level surface and run the
engine to operating temperature.
2. Stop the engine and remove the oil filler cap
(10:J).
3. Place a container under the oil drain plug
(11:N), remove the plug and let the oil run out
into a container.
4. Dispose of the oil according to local regulations.
5. Clean the area around the oil filter (11:M) and
remove the filter. Use an oil filter wrench.
6. Lubricate the gasket on the new filter and screw
this in until the gasket touches the surface of the
engine. Then tighten the filter a further turn using
an oil filter wrench.
7. Install the oil drain plug. Tighten to 60 Nm.
8. Fill with new oil according to “5.3”.
9. After filling the oil, start the engine and run at
idle speed for 30 seconds.
10.Check to see if there is any oil leakage.
11.Stop the engine. Wait for 30 seconds and then
check the oil level. See “5.3”.
6.8 Changing hydraulic oil, filter
No contaminants must enter the hydraulic
system. This causes serious
damage to components of the systems.
Change hydraulic oil and filter as follows:
1. Place the machine on a level surface.
2. Clean the area around the filter (16:A) thoroughly
on the upper part of the hydraulic tank
and remove the filter.
3. Place a container under the oil drain plug
(16:C), remove the plug and let the oil run out
into a container. The container must have a capacity
of 20 litres.
ENGLISH GB
4. Dispose of the oil according to local regulations.
5. Install the oil drain plug. Tighten to 40 Nm.
6. Fill with new oil through the filter opening at
the top.
Oil: See “2.1”.
Oil quantity when changing: See “2.1”.
7. Reinstall the filter with the following components:
17:D Cover
17:G Gasket. Check that the washer is intact.
17:F New filter. The filter must always be replaced
when changing the oil.
17:E Spring
8. After filling the oil, start the engine and run the
machine for a few minutes and check for oil
leakage.
9. Check the oil level. See “3.5.8”.
6.9 Changing the oil in the wheel
motors
Change the oil in the gear housing of the wheel
motors as follows:
1. Place the machine on a level surface.
2. Clean carefully around the
oil plugs (18:X, Y).
3. Place a container under the oil drain plug
(18:X), remove the plug and let the oil run out
into a container.
4. Remove the filler plug (18:Y).
5. Install the oil drain plug.
6. Dispose of the oil according to local regulations.
7. Fill with new oil via the filler plug hole. Pump
in the oil with help of an oil can. Fill until the
level reach the the filler plug hole.
Regarding type and volume of oil, see the table
in “2.1”.
8. Install the filler plug.
9. Tighten the plugs to 30 Nm.
6.10Belt transmissions
After 5 hours of operation check that all belts are
intact and not damaged.
6.11Cleaning the cooling system
After the engine is run, the coolant becomes contaminated
by rust and deposits. This deteriorates
the coolant’s capacity to draw heat from the engine.
Therefore, the coolant must be changed regularly.
Change the coolant as follows:
1. Check that the engine is completely cold.
2. Remove the front engine cover and unscrew the
radiator cap (13:C).
85