PURE POLYUREA - Tecnopol

PROTETTIVO E IMPERMEABILE MEMBRANA LIQUIDA | LIQUID MEMBRANE, WATERPROOF AND PROTECTIVE
DESCRIPTION
DESMOPOL ADY-2C is a polyurethane varnish aliphatic liquid,
high gloss, which encapsulates the substrate with an elastic film
very resistant to corrosion. Color and brightness stable to
ultraviolet radiation. Ceramic finish, without joints. Approved by
the Ministry of Health, according to tests 1991 to be in contact
with foodstuffs.
APPLICATION
In most cases, no primer is needed.
Can be applied with airless spray, roller or brush.
The minimum recommended film for UV protection of other
materials is approximately 300 microns (0.3 mm) equivalent
to 300 grams. product.
Do not apply a second coat until the first non-is dry for good
adhesion.
For indoor application is recommended use respiratory
protection.
In vitrified surfaces should use primer. For more information
contact department technical.
DESMOPOL - ADY.2C comes in two packages separate premeasured.
For your application thoroughly remove the
contents of container component "A" by adding the contents
of the pack Component "B", stirring the mixture until a
homogeneous product.
Brush: Just to touch up. If necessary, add antifoaming, by
mechanical agitation, in a dose between 1 and 2.5%. Avoid
combed regularly.
Roller: Not very advisable. If necessary, add antifoaming, by
mechanical agitation, in a dose between 1 and 2.5%, and use
a rolling glazed wool, hair short.
Spray guns: Only for industrial use.
Airless spray: dilute with 5 to 10% of Desmopol solvent,
according to power the equipment.
- Nozzle 0.007 "to 0.011".
- Pressure at nozzle tip, 180 to 200 kg/cm2.
- Diluted 10% VOC: 440 gr / lt.
Like all coatings and paints, application is performed on firm
substrates dried at a temperature of the upper bearing at 3 º
C the dew point, air temperature above 10 º C and H.R. less
than 80%.
Do not allow more than 48 hours between coats.
Recoat time is approximately 4-24h.
RECOMMENDED USES
All kinds of machinery, equipment, facilities, vehicles, vessels,
structures, walls, doors, pipes, valves, and in general, which
should conjugated resistance, aesthetics and economy
produced for its long duration. Its excellent flexibility and
adhesion allows the coating and protection of flexible funds
nature Thick Epoxy, Polyurea and Polyurethane.
DESMOPOL ADY-2C
Data Sheet
ADVANTAGES
Easy to apply.
No yellow abroad.
High chemical resistance.
Quick drying.
Thixotropic.
Excellent mechanical properties, high resistance
abrasion.
Very good grip, does not need a primer on
most cases.
Prevents corrosion on metal surfaces.
Resistant to high and low temperatures.
It contains no aromatic amines
SUPPORTS
As a finishing coat for TECNOCOAT and DESMOPOL.
CONSUMPTION
Approx. 0.300 kg/m2 and layer
PRESENTATION
In metal containers with 2 total joint components 15 kg.
Component A (5 kg). Component B (10 kg)
TECHNICAL SPECIFICATIONS
Presentation: Two components
Color: All solid colors of our range.
Finish: Satin 60% ± 5 (*)
Specific Gravity: 1.34 gr / cm ³ ± 0.05
Volume Solids: 60% ± 1
Tack Time: 4 hours, at 20 º C and 60% HR.
Recoatable: Min 12 hours, max. 48 hours at 20 ° C 60% RH.
Mixing ratio: A: B = 3: 1 parts by weight with ADY
DESMOPOL 2C "COMP. B ".
Pot-life: 2 hours at 20 º C.
Application: Preferably a gun.
Supply VOC: 375 g / l.
Thinner indicated: Desmopol solvent
PURE POLYUREA
37