Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Táblatartók<br />
Sign Holder<br />
ConFix2<br />
ConFix2<br />
Olyan esetekben amikor a táblát annak megfúrása<br />
nélkül szükséges felszerelni, kiváló<br />
megoldást nyújtanak a soha el nem avuló<br />
ConFix2 családunk elemei.<br />
A 15 mm fejátmérőjű változat szerelési<br />
menete: a tartó alapját a falhoz csavarozzuk,<br />
a táblát a tartó hornyába csúsztatjuk és egy<br />
belső hernyócsavarral a tartóba szorítjuk,<br />
majd a tartót a táblával együtt az alapra illesztjük<br />
és oldalról egy hernyócsavarral<br />
rögzítjük. Egy másik oldalsó hernyócsavar<br />
segítségével a magasság inom állítására is<br />
lehetőség van.<br />
A 25 mm fejátmérőjű változat esetén a<br />
táblát a már falra szerelt tartóba csúsztatjuk<br />
és egy hernyócsavarral rögzítjük.<br />
A szokatlan kivitelezésű „Design“ verziónk<br />
belsejében két darab furatot igénylő<br />
csap található, így ezzel a változattal lehetséges<br />
akár nagyobb táblákat is pusztán egy<br />
tartóval megfogatni.<br />
Termék jellemzők<br />
Átmérő: 15 és 25mm (Duo-tartó csak<br />
25mm),<br />
„Design“ verzió 35mm<br />
Faltávolság: 15mm,<br />
„Design“ verzió 20mm<br />
Befogási tartományok:<br />
15 mm átmérőjű mono tartó: 1-8 mm<br />
25 mm átmérőjű mono tartó: ix 8, vagy<br />
10, vagy 12 mm<br />
25 mm átmérőjű duo tartó: ix 8 mm<br />
„Design“ verzió: 5-8 mm<br />
Két elemből (alap és tartó) áll<br />
Rögzítés belső és oldalsó hernyócsavarokkal<br />
The timeless sign holders of the ConFix2<br />
series are always used when a sign without<br />
holes in the sign material is desired.<br />
To mount the Ø 15mm holder, the core<br />
is screwed to the wall, the shaft with the<br />
clamped and secured (by the rear grub<br />
screw) sign material pushed over it and<br />
then secured with a lateral grub screw. Another<br />
lateral grub screw also allows especially<br />
for larger formats with multiple holders<br />
an additional ine adjustment in height.<br />
With the Ø 25mm holders, the sign material<br />
can be inserted after mounting the<br />
holder and adjusted in height by a grub<br />
screw.<br />
The exceptional mono holder in the „Design“<br />
version requires two holes in the sign<br />
material. This allows larger exhibits to be<br />
stably ixed with only one holder.<br />
Product features<br />
Diameter: 15 and 25mm (duo holder only<br />
25mm);<br />
35mm „Design“ version<br />
Wall clearances: 15mm ( 20mm „Design“<br />
version)<br />
Clamping ranges:<br />
1-4 and 5-8mm respect. (15mm Ø version)<br />
8, 10 or 12mm (Ø 25mm version; duo<br />
holder only 8mm)<br />
5-8mm („Design“ version)<br />
Two-part construction (core and shaft<br />
with clamping guide)<br />
Secured by lateral and inset grub screws<br />
128