13. DRILLING THE HOLES FOR THE HANDLE AND KEY• Lastly, with the help of template UT16I supplied with the machine,you can carry out the drilling necessary to attach the lock,such as the holes for the handle, the chain lock, the key cylin<strong>de</strong>r,etc.AASSEMBLING THE TOOL FOR THE UC16ITEMPLATEB"c"centro caja cerradura "c""c"• Introduce a removable height bar from theequipment insi<strong>de</strong> the holes “A” and sli<strong>de</strong> thetool until the reference mark “0” is over thecentre “c” of the box for the lock (Fig. 19).• Fix using knob B while at the same time levellingthe insi<strong>de</strong> face C of the reference plateon the edge of the door. (Fig. 19).CA(Figure 19)centro caja cerraduraGH "c""c"POSITIONING THE TOOL AND DRILLING• Slacken bushing gui<strong>de</strong> “G” and sli<strong>de</strong> it in ahorizontal direction, placing in<strong>de</strong>x "H" at measurement"D", and retighten it. (Fig. 20).• Using the centre of the mortise as a reference,sli<strong>de</strong> the tool vertically, to position it atmeasurement “E” or “F”, as <strong>de</strong>sired. (Fig. 20).• Once the hole position has been chosen, drillusing a bit Ø 11 mm.• The second hole nee<strong>de</strong>d for the lock can bema<strong>de</strong> by using again the centre "c" of the mortiseas a reference.centro caja cerradura "c"(Figure 20)24 - FC116U / Operating instructions1640148 1640149OPTIONAL DRILLING TOOLS1640148 Enlargement bit D.18 f/gui<strong>de</strong> 111640149 Enlargement bit D.23 f/gui<strong>de</strong> 11
A214. TRIMMING THE LOCKS FOR SEVERAL DOORSU1(Figure 21)S1T1A1• Should you wish to trim several doors and position the locksat the same height, we recommend you use the height bar "A1"(Fig. 21) to simplify this operation.To do this, having <strong>de</strong>termined the height of the lock on the firstdoor, and placed the machine in the trimming position, mount thefour height bars "A1" (Fig. 21) and insert them in the clamp viseapertures "X" (Fig. 22), so that the end limiter disc "A2" (Fig. 21)has its limit at the upper edge of the door, and then fix the heightbar "A1" (Figs. 21 and 22) in this position with the knobs "B1" (Fig.22). For the following door, simply put the machine in place, withthe limiter disc“A2” (Fig. 21) of the height bar “A1” resting on theupper edge of the door, fix the clamp vises in this position andmark the upper reference mark “rs” on this new door for later useso that all the locks remain at the same height.The height bar "A1" (Fig. 21) without the limiter disc "A2" (Fig.21) may also be used, if <strong>de</strong>sired, as a height reference relativeto the floor.JXA1B1XF15. HORIZONTAL MORTISING• To work with the FC116U horizontally, for example to mortisedoors before hanging them, it is advisable to disconnect the damper"T1" (Fig. 21) to leave the movement of carriage "U1" free ofits pressure.To do this, loosen nut "P" (Fig. 23) with key "F" and by moving thescrew knob "R", advance the length indicator "S" towards the endof stroke limiter "A2".Remove knob "S1" (Fig. 21) that fastens silencer "T1" so that thisis disconnected. Keep knob "S1" in a safe place for later use. Finally,adjust the length of the mortising required, as <strong>de</strong>scribed insection 9, before starting work with the machine, as it must neveroperate at the end of stroke, over the maximum length.Q(Figure 22)A216. CORRECTIONS FOR OVERLAPPING DOORSFor mortise trimming of doors with overlap, the centring of themachine and the <strong>de</strong>pth of the edge trimming should be changed,as follows:PCheck that the trimmer is disconnected from themains.F(Figure 23)SR• To centre the machine over the section of the door withoutoverlap, loosen the screws "Q", which lock the clamp vises "X",with key "F" (Fig. 22), and move the plates "J" to the overlapsi<strong>de</strong>, half the width of this in mm, and fix the screws "Q" againin this position.• When the trimming <strong>de</strong>pth is adjusted, as explained in section10, the limiter ring "A" (Fig. 8) must be positioned at a height onthe scale "U" (Fig. 8) which is the sum of the <strong>de</strong>pth necessary forthe lock, plus the height of the door overlap, since the machinewill be supported on this overlap.FC116U / Operating instructions - 25