Pro-Head-Spot

More documents

Recommendations

Info

) Editing via the external controller• Call up the first scene in your controller now.• Select “SC01” by pressing [UP] or [DN].• Press [MODE/ENTER], the display shows “SC01”.• Press [MODE/ENTER], the display shows “C-01”.• Select "CNIN" by pressing [UP] or [DN].• Press [MODE/ENTER], the display shows "OFF".• Press [UP], the display shows "ON".• Press [MODE/ENTER], the display shows "SC02". You successfully downloaded the first scene.• Adjust the Step-time as described above.• Call up the second scene in your controller now.• Repeat steps 5-11 until all desired scenes are downloaded.• Press [EXIT] to exit. The number of steps can be defined under “STEP” and the scenes can be called upunder “RUN”Error MessagesWhen you turn on the fixture, it will make a reset first. The display may show “XXEr” while there areproblems with one or more channels. “XX” stands for the channels equipped with a testing sensor.For example, when the display shows “04Er”, it means there is some error in channel 4. If there aresome errors on channel 1, channel 2, channel 4 at the same time, you may see the error message“01Er”, “02Er”,”4Err” flash repeatly for 5 times, and then the fixture will generate a reset signal, allthe stepper motors will reset. If the error messages maintain after performing reset more than 3times, it will detect whether the fixture has more than 3 errors. If the fixture has more than 3 errors(including 3 errors), all the channels can not work properly; but if the fixture has less than 3 errors,only the channels which have errors can not work properly, others can work as usual.01Er:(PAN-yoke movement error) This message will appear after the reset of the fixture if the yoke’s magneticindexingcircuit malfunction (sensor failed or magnet missing) or the stepping-motor is defective (or its drivingIC on the main PCB). The yoke is not located in the default position after the reset.02Er:(TILT-head movement error) This message will appear after the reset of the fixture if the head’s magneticindexingcircuit malfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or itsdriving IC on the main PCB). The head is not located in the default position after the reset.04Er:(Color-wheel error 1) This message will appear after the reset of the fixture if the magnetic-indexing circuitmalfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or its drive circuit on themain PCB). The color wheel is not located in the default position after the reset.05Er:(Color-wheel error 2) This message will appear after the reset of the fixture if the magnetic-indexing circuitmalfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or its drive circuit on themain PCB). The color wheel is not located in the default position after the reset.06Er:(Rotating gobo-wheel error) This message will appear after the reset of the fixture if the magnetic-indexingcircuit malfunctions(sensor failed or magnet missing) or the stepping-motor is defective (or its drive circuit onthe main PCB). The rotating gobo-wheel is not located in the default position after the reset.07Er:(Rotating gobo indexing error) This message will appear after the reset of the fixture and if the magneticindexingcircuit malfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or its drivercircuit on the main PCB). The rotating gobo is not located in the default position after the reset.08Er:(Static gobo-wheel error 2) This message will appear after the reset of the fixture if the magnetic-indexingcircuit malfunctions(sensor failed or magnet missing) or the stepping-motor is defective (or its drive circuit onthe main PCB). The rotating gobo-wheel is not located in the default position after the reset.54/11351838326_V_1_2.DOC
09Er:(Prism-wheel error) This message will appear after the reset of the fixture and if the magnetic-indexing circuitmalfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or its driver circuit on themain PCB). The prism-wheel is not located in the default position after the reset.10Er:(focus error)11Er:(Iris error)CLEANING AND MAINTENANCEThe operator has to make sure that safety-relating and machine-technical installations are inspected by anexpert after every four years in the course of an acceptance test.The operator has to make sure that safety-relating and machine-technical installations are inspected by askilled person once a year.The following points have to be considered during the inspection:1) All screws used for installing the devices or parts of the device have to be tighly connected and must notbe corroded.2) There must not be any deformations on housings, fixations and installation spots (ceiling, suspension,trussing).3) Mechanically moved parts like axles, eyes and others must not show any traces of wearing (e.g. materialabrading or damages) and must not rotate with unbalances.4) The electric power supply cables must not show any damages, material fatigue (e.g. porous cables) orsediments. Further instructions depending on the installation spot and usage have to be adhered by askilled installer and any safety problems have to be removed.5)DANGER TO LIFE!Disconnect from mains before starting maintenance operation!We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol orsolvents!CAUTION!The lens has to be replaced when it is obviously damaged,so that its function is impaired, e. g. due to cracks or deep scratches!The objective lens will require weekly cleaning as smoke-fluid tends to building up residues, reducing thelight-output very quickly. The cooling-fans should be cleaned monthly.The PHS-710 is equipped with two dust protection filters inside the projector head. These must be cleaned insix month intervals in order to guarantee perfect air circulation.<strong>Pro</strong>cedure:Step 1: Unscrew the fixation screws of the housing cover.Step 2: Remove the housing cover.Step 3: Remove the dust protection filters and clean them.Step 4: Replace the dust protection filters in the housing and tighten the fixationscrews.Step 5: Replace the housing cover and tighten the fixation screws.55/11351838326_V_1_2.DOC
Page 1 and 2:
BEDIENUNGSANLEITUNGUSER MANUALMODE
Page 3 and 4: INTRODUCTION ......................
Page 6 and 7: Bei der ersten Inbetriebnahme kann
Page 8 and 9: Geräteübersicht1234(1) Projektork
Page 10 and 11: LampenjustierungDer Lampenhalter de
Page 12 and 13: Das Gerät kann direkt auf den Bode
Page 14 and 15: Anschluss an den DMX-512 Controller
Page 16 and 17: Die Meldung erscheint-wenn kein 3-p
Page 18 and 19: Steuerkanal 8 - Statisches Goborad,
Page 20 and 21: Control BoardDas Control Board biet
Page 22 and 23: Run - Programm aufrufen, Master-Ein
Page 24 and 25: pan - PAN-UmkehrungMit dieser Funkt
Page 26 and 27: - Betriebsstunden LampeMit dieser F
Page 28 and 29: 06Er:Fehler am rotierenden Goborad.
Page 30 and 31: TECHNISCHE DATENSpannungsversorgung
Page 32 and 33: If the device has been exposed to d
Page 34 and 35: The lamp must never be ignited if t
Page 36 and 37: INSTALLATIONInstalling/Replacing th
Page 38 and 39: RiggingDANGER TO LIFE!Please consid
Page 40 and 41: (1) Omega-holders(2) Clamp(3) Safet
Page 42 and 43: The occupation of the connection-ca
Page 44 and 45: Control-channel 6 - Rotating gobo-w
Page 46 and 47: Control-channel 14 - FrostDecimal H
Page 48 and 49: Main functions- Main menu 0• Pres
Page 50 and 51: Lamp - Main menu 1• Press [MODE/E
Page 52 and 53: - Main menu 3• Press [MODE/ENTER]
Page 56 and 57: Do not operate this device with ope
Page 58 and 59: MODE D'EMPLOIPHS-710Pro-Head-SpotAT
Page 60 and 61: séparer du secteur avec tous les p
Page 62 and 63: Aperçue des parties12345(1) Tête
Page 64 and 65: Ajustage de la lampeLe porte-lampe
Page 66 and 67: L'appareil peut être mis directeme
Page 68 and 69: Connexions au contrôleur DMX-512 /
Page 70 and 71: Attention:L'appareil indique les mo
Page 72 and 73: Canal de contrôle 6 - Roue de gobo
Page 74 and 75: Canal de contrôle 13 - Inténsité
Page 76 and 77: Fonctions principales- Menu princip
Page 78 and 79: Lamp - Menu principal 1• Pressez
Page 80 and 81: - Menu principal 3• Pressez la to
Page 82 and 83: • Pressez la touche Exit pour qui
Page 84 and 85: Procédure:Pas 1: Dévissez les vis
Page 86 and 87: MANUAL DEL USUARIOPHS-710Pro-Head-S
Page 88 and 89: INSTRUCCIONES DE MANEJOEste aparato
Page 90 and 91: Descripción de las partes123456(1)
Page 92 and 93: Ajuste de la lámparaEl sistema de
Page 94 and 95: El aparato puede ser colocadodirect
Page 96 and 97: Conexión al controlador DMX / cone
Page 98 and 99: Note:El aparato indica los modos de
Page 100 and 101: Canal de control 6 - Rueda de gobos
Page 102 and 103: Canal de control 13 - Intensidad de
Page 104 and 105:
Funciones principales- Menu princip
Page 106 and 107:
Lamp - Menu principal 1• Pulse la
Page 108 and 109:
- Menu principal 3• Pulse la tecl
Page 110 and 111:
) Editar mediante el controlador ex
Page 112 and 113:
¡No maneje este aparato con la caj
show all

Pro-Head-Spot

Create successful ePaper yourself

Delete template?

Save as template?