90528012 BDMS200 miter saw

ADDITIONAL SAFETY RULES FOR THE LASERFor your convenience and safety thefollowing labels are on your tool.WARNINGAVOID EXPOSURE:Laser radiation is emited from this aperture.ADVERTENCIAEVITE LA EXPOSICI”N:Por esta abertura se emite radiaciÛn l·ser.AVERTISSEMENT…VITEZ TOUTE EXPOSITION:Rayonnement laser Èmis decette ouverture.CLASS 2LASERRADIATION WHENOPEN DO NOT STAREINTO THE BEAM. L¡ SER CLASE2 EMITE RADIACI” N CUANDO EST¡ABIERTO. NO FIJE LA VISTA EN EL HAZ.MISE EN GARDE : RAYONNEMENT LASERCLASSE 2 UNE FOIS L'OUTIL ALLUM…, NE PASFIXER DU REGARD LE FAISCEAU.CAUTION/ATENCI”N/ATTENTIONLASER RADIATION DO NOT STARE INTO BEAM. CLASS 2 LASERPRODUCT PER EN60825-1:11994+AII+A2 Pmax-1.0mW, =633-670nmRADIACI” N L¡ SER. NO MIRE FIJAMENTE HACIA EL RAYO.PRODUCTO L¡ SER DE CLASE 2.RAYONNEMENT LASER. NE PAS FIXER LE FAISCEAU DUREGARD. PRODUIT LASER DE CLASSE 2.Properly secure cover.Tighten screw before use.Sujete correctamente la tapa. Ajuste eltornillo antes de usar la herramienta.Fixer solidement et correctement lecouvercle. Serrer la vis avant utilisation.COMPLIES WITH 21CFR PARTS 1040.10 AND1040.11 EXCEPT FOR DEVIATIONS PURSUANT TOLASER NOTICE NO.50, DATED JULY 26,2001.CUMPLE CON LAS NORMAS DEL C” DIGO DEREGULACIONES FEDERALES 21CFR 1040.10 Y1040.11, CON LA EXCEPCI” N DE LOSAPARTADOS CONFORMES AL AVISO L¡ SER N∫50, DE FECHA 26 DE JULIO DE 2001.CONFORME AUX SECTIONS 1040.10 ET 1040.11DU CHAP. 21 DU CFR HORMIS LESD…ROGATIONS CONFORM…MENT ¿ LíAVIS N∞50SUR LE LASER, DAT…DU 26 JUILLET 2001.Fig. BFOR LASER SAFETY OBSERVE THE FOLLOWINGCAUTIONS:• LASER LIGHT - DO NOT STARE INTO BEAM, APERTURE, or into a reflectionfrom a mirror-like surface Fig. A & B.• AVOID EXPOSURE - LASER LIGHT IS EMITTED FROM FRONT GUARDAPERTURE. Use of controls or adjustments, or performance of procedures otherthan those specified herein may result in hazardous laser light exposure.• DO NOT DISASSEMBLE LASER MODULE. The laser is a CLASS II LASERPRODUCT that can emit laser power up to 1 mW MAX at 650 nm, which could resultin exposure with the module disassembled. The laser unit complies with 21 CFR1040.10 and 1040.11.• USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OFPROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT INHAZARDOUS RADIATION EXPOSURE.• THE USE OF OPTICAL INSTRUMENTS with this product will increase eyehazard.• LASER RADIATION, avoid direct eye exposure, serious eye injury can result.• DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES, such as in the presence offlammable liquids, gases, or dust.• USE ONLY WITH THE SPECIFICALLY DESIGNATED BATTERIES. Use of any otherbatteries may create a risk of fire.• USE ONLY ACCESSORIES that are recommended by the manufacturer for your model.• ACCESSORIES THAT MAY BE SUITABLE FOR ONE LASER, may create a risk ofinjury when used on another laser.• REPAIRS AND SERVICING MUST be performed by a qualified repair facility. Repairsperformed by unqualified personnel could result in serious injury.• DO NOT REMOVE OR DEFACE WARNING LABELS. Removing labels increases therisk of exposure to radiation.• THIS PRODUCT IS INTENDED for use in a temperature range of 41°F(5°C) -104°F(40°C).7