F/FS 22-120 X/XS22-43

Open the washer door as follows and unload the linen:„A“ MACHINES: By turning the door handle down„B“ MACHINES: By pulling the handle towards you„C“ MACHINES: By holding the lock releasing key and pushing the door handle to the right from the lock4.8.2. FULL CONTROL MICROPROCESSOR MCB FC, MCG FC! WHEN THE POWER SUPPLY HAS BEEN CUT, THE DOOR WILL BE AUTOMATICALLY BLOCKEDAGAINST OPENING. AFTER COOLING DOWN THE WASHING BATH, THE DOOR CAN BE OPENEDACCORDING TO THE MACHINE MAINTENANCE INSTRUCTIONS.At the end of the wash cycle, when the remaining program time reaches 0, PROGRAM END is displayed.When UNLOAD appears on the display, open the door by the door handle and take out the garments of thewasher/extractor.„D“ MACHINESEnd of washing cycle is indicated with green pilot light on the programmer panel (fig. 3.B. pos.7).Unloading the linen is executed manually.„E“ MACHINESEnd of washing cycle is indicated with green pilot light on the programmer panel (fig. 3.B. pos.7).Opening the drum door – see chapter 4.2. „E“ MACHINES.TILTING THE MACHINE FORWARDS TO A POSITION SUITABLE FOR UNLOADING THE LINENYou can tilt the machine forward to any position, extreme position for tilting forwards is 15° from the basicposition. If it is sufficient for you, it is not necessary to tilt the machine up to extreme position. Press thebutton for tilting the machine (fig. 3.B. pos.3) and the button for door opening (6) on the controller at thesame time to tilt the machine. After cca 10s the machine starts tilting. Tilting can be interrupted if yourelease any of the pressed buttons (fig. 3.B. 3, 6). When the extreme position is reached, tilting isstopped. Pressing of other buttons will not influence the machine any more.Tilting forwards is possible only with open drum door.UNLOADING THE LINEN! WARNINGDURING UNLOADING WHILE THE DRUM IS ROTATING, NOBODY MUST STAND IN FRONT OF THEMACHINE. THE LINEN COMES OUT OF THE MACHINE BY ITSELF. DO NOT PULL THE LINEN OUTWHILE THE DRUM IS ROTATING.To make the unloading of the linen easier it is possible to use the functions of drum rotating.For drum rotating in tilted position press and hold the button of drum rotating in required direction (fig.3.B. pos.1)or (2) and the button for the door opening (6) on the controller at the same time. It will make automaticunloading of the linen easier.It is possible to unload the linen into a few steps, it means tilt the machine to certain position and unloadsome linen using the function of the drum rotating. Then tilt the machine more and repeat the process again.TILTING THE MACHINE TO THE BASIC POSITIONAfter unloading the linen, tilt the machine back to basic position, press and hold the button of tilting (fig.3.B. pos.4) and the button of the door opening (6) on the controller at the same time. If you release any ofthe pressed buttons (fig. 3.B. pos.4, 6) you will interrupt the machine tilting. When the basic position is reached,the green pilot light (fig. 3.B. pos.7) lights up on the programmer panel. Release the pressed buttons.Luminous green pilot light (fig. 3.B. pos.7) indicates the basic position of the machine when thedoor is open. When the door is closed, it indicates that opening the door is possible (as far as theother failure does not occur).When the power supply is interrupted during tilting, the machine remains secured in its actualposition as well as after the power supply restart.4.9. HOW TO OPEN DOOR WHEN FAILURE OCCURS! WARNING!1. THIS HANDLING SHOULD ONLY BE DONE BY QUALIFIED TECHNICIANS!2. MAKE SURE THAT THE DRUM HAS COMPLETELY STOPPED AND DRAINED BEFORE OPENING THE DOOR!3. OPENING THE DOOR WHILE THERE IS STILL HOT WATER IN THE DRUM CAN CAUSE SERIOUSBURNS! MAKE SURE THAT THE REMAINING WATER IS COMPLETELY COOLED DOWN BEFOREYOU OPEN THE DOOR!14 USER´S MANUAL PUBLICATION DATE 05/05 507 329