HEME GEO 30 - Tequipment.net

More documents

Recommendations

Info

Description of InstrumentDisplay Function Digits OhmDisplay of current selected function or current recordnumberDisplay value from 0 to 9999 with decimal point.Symbol will be shown in Ω and alarm functions mA NOISE: Jaw Open Low Battery NO. REC1APDisplay ground leakage current in mA or AThis symbol is displayed if the rotary switch is in the alarmpositionNoise present in ground electrode or ground rod.If the jaw is not properly closed during measurement, thissymbol and the word ”OPEN” will be shown on the LCD.When the battery voltage is lower than required,this symbol will be shown in LCD. Replace thebattery.Indicate the READ functionIndicates data logging is in progressIndicate Autopower off will operate in 4 to 6 minutes8 HEME GEO 30SO8130Z Rev. B
Ground Loop Measurements3 Ground Loop Measurements Open the jaws and make sure the jaw mating surfaces are clean and free of dust,dirt or any foreign substances. Snap (open and close) the jaws a few times to ensure the jaws mate properly. Turn the power on, and set the rotary switch to the Ω position.Do not clamp on to any conductor or open the jaws at this moment orduring self-calibration. At powering on, the clamp-on ground tester will self-calibrate for better accuracy.Users should wait for the self-calibration to finish before making measurements.During the self-calibration, the LCD will show CAL7, CAL6,..., CAL2, CAL1. When the ground tester is ready, a beep sound will be heard. Clamp on to the electrode or ground rod to be measured. Read the value of R g (ground loop resistance) from LCD.Note: For better measurement:Snap (open and close) the jaws a few times before powering on.Do not clamp on to any conductor at the moment of powering on.Note: If self-calibration does not stop:This is because the self-calibration is not complete. The ground tester willcontinue the process until a proper self-calibration is complete.Check the jaw mating surfaces. If there is any dirt, dust, or any foreignsubstance, clean the surface and power up again.Note: Noise present in the electrode or ground rod:If there exists over 3A current or 30V in ground rod, the symbol ”NOISE” will beshown in LCD. Under the presence of noise, the reading is no longer accurate.Note: If the jaw assembly is open during measurement, a symbol and the word”OPEN” will be displayed on LCD.HEME GEO 30 9SO8130Z Rev. B
Page 5: Safety Regulations1 Safety Regulati
Page 11 and 12: Continuity Loop Test4 Continuity Lo
Page 13: Memory and Alarm Functions6 Memory
Page 16 and 17: Memory and Alarm Functions6.4 Read
Page 18: Principle of OperationFig. 1: Typic
Page 21 and 22: SpecificationBattery ReplacementWhe
Page 23 and 24: Other Products10 Other productsLEM
Page 25 and 26: InhaltsverzeichnisInhaltsverzeichni
Page 27 and 28: Sicherheitsbestimmungen1 Sicherheit
Page 29: Mit dieser Taste werden Werte erhö
Page 34 and 35: Messung des Erdleckstroms5 Messung
Page 36 and 37: HOLDOFFSpeicher- und Alarmfunktione
Page 38 and 39: Speicher- und Alarmfunktionen6.4 Au
Page 40 and 41: ArbeitsprinzipBild 1: Typische geer
Page 42 and 43: KennwerteErdschleifenwiderstand (Au
Page 44: Wartung, Instandhaltung9 Wartung, I
Page 47 and 48: SommaireSommaire1 Règlements de s
Page 49 and 50: Règlements de sécurité1 Règleme
Page 51 and 52: Pour diminuer la valeur, appuyer su
Page 53 and 54: Mesures de résistance de terre3 Me
Page 55 and 56: Essai de continuité en boucle4 Ess
Page 57 and 58: 6 Fonctions de mémoire et d’alar
Page 59 and 60:
Fonctions de mémoire et d’alarme
Page 61 and 62:
Principe de fonctionnement7 Princip
Page 63 and 64:
Spécification8 SpécificationSpéc
Page 65 and 66:
SpécificationRemplacement de la pi
Page 67 and 68:
Autres produits10 Autres produitsLE
Page 69 and 70:
IndiceIndice1 Prescrizioni di sicur
Page 71 and 72:
Prescrizioni di sicurezza1 Prescriz
Page 73 and 74:
Pulsante REC:Descrizionequando una
Page 75 and 76:
Misurazioni su circuiti di terra3 M
Page 77 and 78:
4 Verifica della continuità nei ci
Page 79 and 80:
Funzioni di memoria e allarme6 Funz
Page 81 and 82:
6.2 Impostazione dell’intervallo
Page 83 and 84:
Principio di funzionamento7 Princip
Page 85 and 86:
Caratteristiche8 CaratteristicheCar
Page 87 and 88:
CaratteristicheSostituzione della b
Page 89 and 90:
Altri prodotti10 Altri prodottiIl g
Page 91 and 92:
ÍndiceÍndice de materias1 Normas
Page 93 and 94:
Normas de seguridad1 Normas de segu
Page 95 and 96:
Descripción del instrumento& botó
Page 97 and 98:
3 Mediciones de resistencia de tier
Page 99 and 100:
4 Prueba de continuidad con buclePr
Page 101 and 102:
6 Funciones de alarma y memoria6.1
Page 103 and 104:
Funciones de alarma y memoria6.2 Co
Page 105 and 106:
Principio de funcionamiento7 Princi
Page 107 and 108:
Valores específicos8 Valores espec
Page 109 and 110:
Valores específicosSustitución de
Page 111 and 112:
Otro productos10 Otro productosLEM
Page 113 and 114:
EC-Certificate of conformityEG-Konf
show all

HEME GEO 30 - Tequipment.net

Create successful ePaper yourself

Delete template?

Save as template?