CARSON CE-10T Brushless - Tamiya

More documents

Recommendations

Info

GBg. How to Control your Model• Raise the tyres off the ground.• Turn the steering wheel to the right and left as far as it willgo. The wheels are to follow the steering direction.• If the wheels operate in the opposite direction, operate theservo Reverse switch (ST in position REV).NeutralLeftLeft RightRight• For regulating the driving speed operate the gas/brake- lever to the rear (driving forward, to give speed)- and/or forward (braking, reverse movement)driving forward,to give speedbraking, reversemovement10CARSON CE-10T Brushless
h. How to Change FrequenciesTransmitterA rapid change of frequencies is possible simply by unpluggingan interchangeable plug in crystal on the back of thetransmitter and thenplugging in another one Crystalof a different frequency.Crystals for both thetransmitter and receivermust be matched witheach other.Make sure that thecrystal is fully insertedin the transmitter andreceiver, not partially.ReceiverPlug in an interchangeable crystal into the receiver for a rapidchange of frequencies.CrystalGBTXBAND2i. TroubleshootingProblem Cause CorrectionModel doesn´t move Transmitter or chassis power switch is not ”ON“ Switch power onPolarity or battery type is wrongCheck polarity and typeBatteries have run downChange batteries or charge themLoss of control Batteries have run down Change batteries or charge themAntenna is missing or not attached properly Attach antenna and extend transmitterantenna to full lengthR/C model using same band (frequency) is Run model in different area or change crystalnearbyDoesn´t run straight Steering trim is not adjusted correctly Make adjustmentFront and rear wheel nuts are too loseTighten wheel nutsDoesn´t stop Throttle trim is not adjusted correctly Make adjustmentDoesn´t reverse Throttle trim is not adjusted correctly Make adjustmentWrong actionControl properlyRunning too slowly Batteries have run down Change batteries or charge themMotor has lost powerChange to spare motorRear wheel nuts are too looseTighten wheel nutsDust or foreign objects are inside gearsTurn the power switch ”OFF“ and clean outgearsCARSON CE-10T Brushless11
Page 1 and 2: CE-10 TBrushlessInstruction Manual
Page 3 and 4: ContentsPreface ...................
Page 5 and 6: FinallyPlease read the instructions
Page 9: CAUTION!Always turn the transmitter
Page 13 and 14: InhaltVorwort .....................
Page 15 and 16: Zum SchlussBitte lesen Sie diese Be
Page 17 and 18: . Abnehmen der Karosserie• Ziehen
Page 19 and 20: ACHTUNG!Immer zuerst den Sender ein
Page 21 and 22: h. Wechseln der SendefrequenzSender
Page 23 and 24: Préface ..........................
Page 25 and 26: Derniers conseils :Lire attentiveme
Page 27 and 28: . Retrait de la carrosserie• Reti
Page 29 and 30: ATTENTION !Toujours allumer l’ém
Page 31 and 32: h. Changer les fréquencesEmetteurU
Page 33 and 34: Indice decontenidosPrólogo .......
Page 35 and 36: Por finDespués de cada uso, todas
Page 37 and 38: . Cuitar la Carrocería• Quite lo
Page 39 and 40: PRECAUCION¡Conecte siempre primero
Page 41 and 42: h. Cómo cambiar frecuenciasEmisora
Page 43 and 44: ContenutoPrefazione ...............
Page 45 and 46: A Fine UtilizzoDopo ogni utilizzo,
Page 47 and 48: . Rimuovere la carrozzeria• Sfila
Page 49 and 50: ATTENZIONE!Accendere sempre prima i
Page 51 and 52: h. Come cambiare la frequenzaTrasme
Page 53 and 54: 50 010 5149 10x5x4 mm3Suspension as
Page 55 and 56: 50 010 5191 M3x350 010 51845Front a
Page 57 and 58: 50 010 5149 10x5x4 mm7Rear suspensi
Page 59 and 60: 50 010 51509Servosaver complete •
Page 61 and 62:
50 010 5190 ISO3x850 010 5190 TPF3x
Page 63 and 64:
50 010 519013Mounting of the comple
Page 65 and 66:
MontageCARSON CE-10T Brushless65
Page 67 and 68:
Spare Parts • Ersatzteile • Pi
Page 69 and 70:
NotizenCARSON CE-10T Brushless69
Page 71 and 72:
NotizenCARSON CE-10T Brushless71
show all

CARSON CE-10T Brushless - Tamiya

Create successful ePaper yourself

Delete template?

Save as template?